SLAU847E October   2022  â€“ May 2025 MSPM0L1105 , MSPM0L1106 , MSPM0L1116 , MSPM0L1117 , MSPM0L1227 , MSPM0L1227-Q1 , MSPM0L1228 , MSPM0L1228-Q1 , MSPM0L1303 , MSPM0L1304 , MSPM0L1304-Q1 , MSPM0L1305 , MSPM0L1305-Q1 , MSPM0L1306 , MSPM0L1306-Q1 , MSPM0L1343 , MSPM0L1344 , MSPM0L1345 , MSPM0L1346 , MSPM0L2227 , MSPM0L2227-Q1 , MSPM0L2228 , MSPM0L2228-Q1

 

  1.   1
  2.   Read This First
    1.     About This Manual
    2.     Notational Conventions
    3.     Glossary
    4.     Related Documentation
    5.     Support Resources
    6.     Trademarks
  3. 1 Architecture
    1. 1.1 Architecture Overview
    2. 1.2 Bus Organization
    3. 1.3 Platform Memory Map
      1. 1.3.1 Code Region
      2. 1.3.2 SRAM Region
      3. 1.3.3 Peripheral Region
      4. 1.3.4 Subsystem Region
      5. 1.3.5 System PPB Region
    4. 1.4 Boot Configuration
      1. 1.4.1 Configuration Memory (NONMAIN)
        1. 1.4.1.1 CRC-Backed Configuration Data
        2. 1.4.1.2 16-bit Pattern Match for Critical Fields
      2. 1.4.2 Boot Configuration Routine (BCR)
        1. 1.4.2.1 Serial Wire Debug Related Policies
          1. 1.4.2.1.1 SWD Security Level 0
          2. 1.4.2.1.2 SWD Security Level 1
          3. 1.4.2.1.3 SWD Security Level 2
        2. 1.4.2.2 SWD Mass Erase and Factory Reset Commands
        3. 1.4.2.3 Flash Memory Protection and Integrity Related Policies
          1. 1.4.2.3.1 Locking the Application (MAIN) Flash Memory
          2. 1.4.2.3.2 Locking the Configuration (NONMAIN) Flash Memory
          3. 1.4.2.3.3 Static Write Protection NONMAIN Fields
        4. 1.4.2.4 Application CRC Verification
        5. 1.4.2.5 Fast Boot
        6. 1.4.2.6 Bootstrap Loader (BSL) Enable/Disable Policy
          1. 1.4.2.6.1 BSL Enable
      3. 1.4.3 Bootstrap Loader (BSL)
        1. 1.4.3.1 GPIO Invoke
        2. 1.4.3.2 Bootstrap Loader (BSL) Security Policies
          1. 1.4.3.2.1 BSL Access Password
          2. 1.4.3.2.2 BSL Read-out Policy
          3. 1.4.3.2.3 BSL Security Alert Policy
        3. 1.4.3.3 Application Version
        4. 1.4.3.4 BSL Triggered Mass Erase and Factory Reset
      4. 1.4.4 NONMAIN Layout Types
      5. 1.4.5 NONMAIN_TYPEA Registers
      6. 1.4.6 NONMAIN_TYPEC Registers
      7. 1.4.7 NONMAIN_TYPEE Registers
    5. 1.5 Factory Constants
      1. 1.5.1 FACTORYREGION Registers
  4. 2 PMCU
    1. 2.1 PMCU Overview
      1. 2.1.1 Power Domains
      2. 2.1.2 Operating Modes
        1. 2.1.2.1 RUN Mode
        2. 2.1.2.2 SLEEP Mode
        3. 2.1.2.3 STOP Mode
        4. 2.1.2.4 STANDBY Mode
        5. 2.1.2.5 SHUTDOWN Mode
        6. 2.1.2.6 Supported Functionality by Operating Mode
        7. 2.1.2.7 Suspended Low-Power Mode Operation
    2. 2.2 Power Management (PMU)
      1. 2.2.1 Power Supply
      2. 2.2.2 Core Regulator
      3. 2.2.3 Supply Supervisors
        1. 2.2.3.1 Power-on Reset (POR)
        2. 2.2.3.2 Brownout Reset (BOR)
        3. 2.2.3.3 POR and BOR Behavior During Supply Changes
      4. 2.2.4 Bandgap Reference
      5. 2.2.5 VBOOST for Analog Muxes
      6. 2.2.6 Peripheral Enable
        1. 2.2.6.1 Automatic Peripheral Disable in Low Power Modes
    3. 2.3 Clock Module (CKM)
      1. 2.3.1 Oscillators
        1. 2.3.1.1 Internal Low-Frequency Oscillator (LFOSC)
        2. 2.3.1.2 Internal System Oscillator (SYSOSC)
          1. 2.3.1.2.1 SYSOSC Gear Shift
          2. 2.3.1.2.2 SYSOSC Frequency and User Trims
          3. 2.3.1.2.3 SYSOSC Frequency Correction Loop
            1. 2.3.1.2.3.1 SYSOSC FCL in External Resistor Mode (ROSC)
            2. 2.3.1.2.3.2 SYSOSC FCL in Internal Resistor Mode
          4. 2.3.1.2.4 SYSOSC User Trim Procedure
          5. 2.3.1.2.5 Disabling SYSOSC
        3. 2.3.1.3 Low Frequency Crystal Oscillator (LFXT)
        4. 2.3.1.4 LFCLK_IN (Digital Clock)
        5. 2.3.1.5 High Frequency Crystal Oscillator (HFXT)
        6. 2.3.1.6 HFCLK_IN (Digital clock)
      2. 2.3.2 Clocks
        1. 2.3.2.1  MCLK (Main Clock) Tree
        2. 2.3.2.2  CPUCLK (Processor Clock)
        3. 2.3.2.3  ULPCLK (Low-Power Clock)
        4. 2.3.2.4  MFCLK (Middle Frequency Clock)
        5. 2.3.2.5  MFPCLK (Middle Frequency Precision Clock)
        6. 2.3.2.6  LFCLK (Low-Frequency Clock)
        7. 2.3.2.7  HFCLK (High-Frequency External Clock)
        8. 2.3.2.8  HSCLK (High Speed Clock)
        9. 2.3.2.9  ADCCLK (ADC Sample Period Clock)
        10. 2.3.2.10 RTCCLK (RTC Clock)
        11. 2.3.2.11 External Clock Output (CLK_OUT)
        12. 2.3.2.12 Direct Clock Connections for Infrastructure
      3. 2.3.3 Clock Tree
        1. 2.3.3.1 Peripheral Clock Source Selection
      4. 2.3.4 Clock Monitors
        1. 2.3.4.1 LFCLK Monitor
        2. 2.3.4.2 MCLK Monitor
        3. 2.3.4.3 Startup Monitors
          1. 2.3.4.3.1 LFOSC Startup Monitor
          2. 2.3.4.3.2 LFXT Startup Monitor
          3. 2.3.4.3.3 HFCLK Startup Monitor
          4. 2.3.4.3.4 HSCLK Status
      5. 2.3.5 Frequency Clock Counter (FCC)
        1. 2.3.5.1 Using the FCC
        2. 2.3.5.2 FCC Frequency Computation and Accuracy
    4. 2.4 System Controller (SYSCTL)
      1. 2.4.1  Resets and Device Initialization
        1. 2.4.1.1 Reset Levels
          1. 2.4.1.1.1 Power-on Reset (POR) Reset Level
          2. 2.4.1.1.2 Brownout Reset (BOR) Reset Level
          3. 2.4.1.1.3 Boot Reset (BOOTRST) Reset Level
          4. 2.4.1.1.4 System Reset (SYSRST) Reset Level
          5. 2.4.1.1.5 CPU-only Reset (CPURST) Reset Level
        2. 2.4.1.2 Initial Conditions After POR
        3. 2.4.1.3 NRST Pin
        4. 2.4.1.4 SWD Pins
        5. 2.4.1.5 Generating Resets in Software
        6. 2.4.1.6 Reset Cause
        7. 2.4.1.7 Peripheral Reset Control
        8. 2.4.1.8 Boot Fail Handling
      2. 2.4.2  Operating Mode Selection
      3. 2.4.3  Asynchronous Fast Clock Requests
      4. 2.4.4  SRAM Write Protection
      5. 2.4.5  Flash Wait States
      6. 2.4.6  Flash Bank Address Swap
      7. 2.4.7  Shutdown Mode Handling (if present)
      8. 2.4.8  Configuration Lockout
      9. 2.4.9  System Status
      10. 2.4.10 Error Handling
      11. 2.4.11 SYSCTL Events
        1. 2.4.11.1 CPU Interrupt Event (CPU_INT)
        2. 2.4.11.2 Nonmaskable Interrupt Event (NMI)
    5. 2.5 Quick Start Reference
      1. 2.5.1 Default Device Configuration
      2. 2.5.2 Leveraging MFCLK
      3. 2.5.3 Optimizing Power Consumption in STOP Mode
      4. 2.5.4 Optimizing Power Consumption in STANDBY Mode
      5. 2.5.5 Increasing MCLK and ULPCLK Precision
      6. 2.5.6 High Speed Clock (SYSPLL, HFCLK) Handling in Low-Power Modes
      7. 2.5.7 Optimizing for Lowest Wakeup Latency
      8. 2.5.8 Optimizing for Lowest Peak Current in RUN/SLEEP Mode
    6. 2.6 SYSCTL Layout Types
    7. 2.7 SYSCTL_TYPEA Registers
    8. 2.8 SYSCTL_TYPEB Registers
    9. 2.9 SYSCTL_TYPEC Registers
  5. 3 CPU
    1. 3.1 Overview
    2. 3.2 Arm Cortex-M0+ CPU
      1. 3.2.1 CPU Register File
      2. 3.2.2 Stack Behavior
      3. 3.2.3 Execution Modes and Privilege Levels
      4. 3.2.4 Address Space and Supported Data Sizes
    3. 3.3 Interrupts and Exceptions
      1. 3.3.1 Peripheral Interrupts (IRQs)
        1. 3.3.1.1 Nested Vectored Interrupt Controller (NVIC)
        2. 3.3.1.2 Interrupt Groups
        3. 3.3.1.3 Wake Up Controller (WUC)
      2. 3.3.2 Interrupt and Exception Table
      3. 3.3.3 Processor Lockup Scenario
    4. 3.4 CPU Peripherals
      1. 3.4.1 System Control Block (SCB)
      2. 3.4.2 System Tick Timer (SysTick)
    5. 3.5 Read-Only Memory (ROM)
    6. 3.6 CPUSS Registers
    7. 3.7 WUC Registers
  6. 4 SECURITY
    1. 4.1 Overview
      1. 4.1.1 Secure Boot
      2. 4.1.2 Customer Secure Code (CSC)
    2. 4.2 Boot and Startup Sequence
      1. 4.2.1 CSC Programming Overview
    3. 4.3 Secure Key Storage
    4. 4.4 Flash Memory Protection
      1. 4.4.1 Bank Swapping
      2. 4.4.2 Write Protection
      3. 4.4.3 Read-Execute Protection
      4. 4.4.4 IP Protection
      5. 4.4.5 Data Bank Protection
      6. 4.4.6 Hardware Monotonic Counter
    5. 4.5 SRAM Protection
    6. 4.6 SECURITY Registers
  7. 5 DMA
    1. 5.1 DMA Overview
    2. 5.2 DMA Operation
      1. 5.2.1  Addressing Modes
      2. 5.2.2  Channel Types
      3. 5.2.3  Transfer Modes
        1. 5.2.3.1 Single Transfer
        2. 5.2.3.2 Block Transfer
        3. 5.2.3.3 Repeated Single Transfer
        4. 5.2.3.4 Repeated Block Transfer
        5. 5.2.3.5 Stride Mode
      4. 5.2.4  Extended Modes
        1. 5.2.4.1 Fill Mode
        2. 5.2.4.2 Table Mode
      5. 5.2.5  Initiating DMA Transfers
      6. 5.2.6  Stopping DMA Transfers
      7. 5.2.7  Channel Priorities
      8. 5.2.8  Burst Block Mode
      9. 5.2.9  Using DMA with System Interrupts
      10. 5.2.10 DMA Controller Interrupts
      11. 5.2.11 DMA Trigger Event Status
      12. 5.2.12 DMA Operating Mode Support
        1. 5.2.12.1 Transfer in RUN Mode
        2. 5.2.12.2 Transfer in SLEEP Mode
        3. 5.2.12.3 Transfer in STOP Mode
        4. 5.2.12.4 Transfers in STANDBY Mode
      13. 5.2.13 DMA Address and Data Errors
      14. 5.2.14 Interrupt and Event Support
    3. 5.3 DMA Registers
  8. 6 NVM (Flash)
    1. 6.1 NVM Overview
      1. 6.1.1 Key Features
      2. 6.1.2 System Components
      3. 6.1.3 Terminology
    2. 6.2 Flash Memory Bank Organization
      1. 6.2.1 Banks
      2. 6.2.2 Flash Memory Regions
      3. 6.2.3 Addressing
        1. 6.2.3.1 Flash Memory Map
      4. 6.2.4 Memory Organization Examples
    3. 6.3 Flash Controller
      1. 6.3.1 Overview of Flash Controller Commands
      2. 6.3.2 NOOP Command
      3. 6.3.3 PROGRAM Command
        1. 6.3.3.1 Program Bit Masking Behavior
        2. 6.3.3.2 Programming Less Than One Flash Word
        3. 6.3.3.3 Target Data Alignment (Devices with Single Flash Word Programming Only)
        4. 6.3.3.4 Target Data Alignment (Devices With Multiword Programming)
        5. 6.3.3.5 Executing a PROGRAM Operation
      4. 6.3.4 ERASE Command
        1. 6.3.4.1 Erase Sector Masking Behavior
        2. 6.3.4.2 Executing an ERASE Operation
      5. 6.3.5 READVERIFY Command
        1. 6.3.5.1 Executing a READVERIFY Operation
      6. 6.3.6 BLANKVERIFY Command
        1. 6.3.6.1 Executing a BLANKVERIFY Operation
      7. 6.3.7 Command Diagnostics
        1. 6.3.7.1 Command Status
        2. 6.3.7.2 Address Translation
        3. 6.3.7.3 Pulse Counts
      8. 6.3.8 Overriding the System Address With a Bank ID, Region ID, and Bank Address
      9. 6.3.9 FLASHCTL Events
        1. 6.3.9.1 CPU Interrupt Event Publisher
    4. 6.4 Write Protection
      1. 6.4.1 Write Protection Resolution
      2. 6.4.2 Static Write Protection
      3. 6.4.3 Dynamic Write Protection
        1. 6.4.3.1 Configuring Protection for the MAIN Region
        2. 6.4.3.2 Configuring Protection for the NONMAIN Region
    5. 6.5 Read Interface
      1. 6.5.1 Bank Address Swapping
    6. 6.6 FLASHCTL Registers
  9. 7 Events
    1. 7.1 Events Overview
      1. 7.1.1 Event Publisher
      2. 7.1.2 Event Subscriber
      3. 7.1.3 Event Fabric Routing
        1. 7.1.3.1 CPU Interrupt Event Route (CPU_INT)
        2. 7.1.3.2 DMA Trigger Event Route (DMA_TRIGx)
        3. 7.1.3.3 Generic Event Route (GEN_EVENTx)
      4. 7.1.4 Event Routing Map
      5. 7.1.5 Event Propagation Latency
    2. 7.2 Events Operation
      1. 7.2.1 CPU Interrupt
      2. 7.2.2 DMA Trigger
      3. 7.2.3 Peripheral to Peripheral Event
      4. 7.2.4 Extended Module Description Register
      5. 7.2.5 Using Event Registers
        1. 7.2.5.1 Event Registers
        2. 7.2.5.2 Configuring Events
        3. 7.2.5.3 Responding to CPU Interrupts in Application Software
        4. 7.2.5.4 Hardware Event Handling
  10. 8 IOMUX
    1. 8.1 IOMUX Overview
      1. 8.1.1 IO Types and Analog Sharing
    2. 8.2 IOMUX Operation
      1. 8.2.1 Peripheral Function (PF) Assignment
      2. 8.2.2 Logic High to Hi-Z Conversion
      3. 8.2.3 Logic Inversion
      4. 8.2.4 SHUTDOWN Mode Wakeup Logic
      5. 8.2.5 Pullup/Pulldown Resistors
      6. 8.2.6 Drive Strength Control
      7. 8.2.7 Hysteresis and Logic Level Control
    3. 8.3 IOMUX Registers
  11. 9 GPIO
    1. 9.1 GPIO Overview
    2. 9.2 GPIO Operation
      1. 9.2.1 GPIO Ports
      2. 9.2.2 GPIO Read/Write Interface
      3. 9.2.3 GPIO Input Glitch Filtering and Synchronization
      4. 9.2.4 GPIO Fast Wake
      5. 9.2.5 GPIO DMA Interface
      6. 9.2.6 Event Publishers and Subscribers
    3. 9.3 GPIO Registers
  12. 10AESADV
    1. 10.1 AESADV Overview
      1. 10.1.1 AESADV Performance
    2. 10.2 AESADV Operation
      1. 10.2.1 Loading the Key
      2. 10.2.2 Writing Input Data
      3. 10.2.3 Reading Output Data
      4. 10.2.4 Operation Descriptions
        1. 10.2.4.1 Single Block Operation
        2. 10.2.4.2 Electronic Codebook (ECB) Mode
          1. 10.2.4.2.1 ECB Encryption
          2. 10.2.4.2.2 ECB Decryption
        3. 10.2.4.3 Cipher Block Chaining (CBC) Mode
          1. 10.2.4.3.1 CBC Encryption
          2. 10.2.4.3.2 CBC Decryption
        4. 10.2.4.4 Output Feedback (OFB) Mode
          1. 10.2.4.4.1 OFB Encryption
          2. 10.2.4.4.2 OFB Decryption
        5. 10.2.4.5 Cipher Feedback (CFB) Mode
          1. 10.2.4.5.1 CFB Encryption
          2. 10.2.4.5.2 CFB Decryption
        6. 10.2.4.6 Counter (CTR) Mode
          1. 10.2.4.6.1 CTR Encryption
          2. 10.2.4.6.2 CTR Decryption
        7. 10.2.4.7 Galois Counter (GCM) Mode
          1. 10.2.4.7.1 GHASH Operation
          2. 10.2.4.7.2 GCM Operating Modes
            1. 10.2.4.7.2.1 Autonomous GCM Operation
              1. 10.2.4.7.2.1.1 GMAC
            2. 10.2.4.7.2.2 GCM With Pre-Calculations
            3. 10.2.4.7.2.3 GCM Operation With Precalculated H- and Y0-Encrypted Forced to Zero
        8. 10.2.4.8 Counter With Cipher Block Chaining Message Authentication Code (CCM)
          1. 10.2.4.8.1 CCM Operation
      5. 10.2.5 AES Events
        1. 10.2.5.1 CPU Interrupt Event Publisher (CPU_EVENT)
        2. 10.2.5.2 DMA Trigger Event Publisher (DMA_TRIG_DATAIN)
        3. 10.2.5.3 DMA Trigger Event Publisher (DMA_TRIG_DATAOUT)
    3. 10.3 AESADV Registers
  13. 11CRC
    1. 11.1 CRC Overview
      1. 11.1.1 CRC16-CCITT
      2. 11.1.2 CRC32-ISO3309
    2. 11.2 CRC Operation
      1. 11.2.1 CRC Generator Implementation
      2. 11.2.2 Configuration
        1. 11.2.2.1 Polynomial Selection
        2. 11.2.2.2 Bit Order
        3. 11.2.2.3 Byte Swap
        4. 11.2.2.4 Byte Order
        5. 11.2.2.5 CRC C Library Compatibility
    3. 11.3 CRCP0 Registers
  14. 12Keystore
    1. 12.1 Overview
    2. 12.2 Detailed Description
    3. 12.3 KEYSTORECTL Registers
  15. 13TRNG
    1. 13.1 TRNG Overview
    2. 13.2 TRNG Operation
      1. 13.2.1 TRNG Generation Data Path
      2. 13.2.2 Clock Configuration and Output Rate
      3. 13.2.3 Behavior in Low Power Modes
      4. 13.2.4 Health Tests
        1. 13.2.4.1 Digital Block Startup Self-Test
        2. 13.2.4.2 Analog Block Startup Self-Test
        3. 13.2.4.3 Runtime Health Test
          1. 13.2.4.3.1 Repetition Count Test
          2. 13.2.4.3.2 Adaptive Proportion Test
          3. 13.2.4.3.3 Handling Runtime Health Test Failures
      5. 13.2.5 Configuration
        1. 13.2.5.1 TRNG State Machine
          1. 13.2.5.1.1 Changing TRNG States
        2. 13.2.5.2 Using the TRNG
        3. 13.2.5.3 TRNG Events
          1. 13.2.5.3.1 CPU Interrupt Event Publisher (CPU_INT)
    3. 13.3 TRNG Registers
  16. 14Temperature Sensor
  17. 15ADC
    1. 15.1 ADC Overview
    2. 15.2 ADC Operation
      1. 15.2.1  ADC Core
      2. 15.2.2  Voltage Reference Options
      3. 15.2.3  Generic Resolution Modes
      4. 15.2.4  Hardware Averaging
      5. 15.2.5  ADC Clocking
      6. 15.2.6  Common ADC Use Cases
      7. 15.2.7  Power Down Behavior
      8. 15.2.8  Sampling Trigger Sources and Sampling Modes
        1. 15.2.8.1 AUTO Sampling Mode
        2. 15.2.8.2 MANUAL Sampling Mode
      9. 15.2.9  Sampling Period
      10. 15.2.10 Conversion Modes
      11. 15.2.11 Data Format
      12. 15.2.12 Advanced Features
        1. 15.2.12.1 Window Comparator
        2. 15.2.12.2 DMA and FIFO Operation
        3. 15.2.12.3 Analog Peripheral Interconnection
      13. 15.2.13 Status Register
      14. 15.2.14 ADC Events
        1. 15.2.14.1 CPU Interrupt Event Publisher (CPU_INT)
        2. 15.2.14.2 Generic Event Publisher (GEN_EVENT)
        3. 15.2.14.3 DMA Trigger Event Publisher (DMA_TRIG)
        4. 15.2.14.4 Generic Event Subscriber (FSUB_0)
    3. 15.3 ADC12 Registers
  18. 16COMP
    1. 16.1 Comparator Overview
    2. 16.2 Comparator Operation
      1. 16.2.1  Comparator Configuration
      2. 16.2.2  Comparator Channels Selection
      3. 16.2.3  Comparator Output
      4. 16.2.4  Output Filter
      5. 16.2.5  Sampled Output Mode
      6. 16.2.6  Blanking Mode
      7. 16.2.7  Reference Voltage Generator
      8. 16.2.8  Comparator Hysteresis
      9. 16.2.9  Input SHORT Switch
      10. 16.2.10 Interrupt and Events Support
        1. 16.2.10.1 CPU Interrupt Event Publisher (CPU_INT)
        2. 16.2.10.2 Generic Event Publisher (GEN_EVENT)
        3. 16.2.10.3 Generic Event Subscribers
    3. 16.3 COMP Registers
  19. 17OPA
    1. 17.1 OPA Overview
    2. 17.2 OPA Operation
      1. 17.2.1 Analog Core
      2. 17.2.2 Power Up Behavior
      3. 17.2.3 Inputs
      4. 17.2.4 Output
      5. 17.2.5 Clock Requirements
      6. 17.2.6 Chopping
      7. 17.2.7 OPA Amplifier Modes
        1. 17.2.7.1 General-Purpose Mode
        2. 17.2.7.2 Buffer Mode
        3. 17.2.7.3 OPA PGA Mode
          1. 17.2.7.3.1 Inverting PGA Mode
          2. 17.2.7.3.2 Non-inverting PGA Mode
        4. 17.2.7.4 Difference Amplifier Mode
        5. 17.2.7.5 Cascade Amplifier Mode
      8. 17.2.8 OPA Configuration Selection
      9. 17.2.9 Burnout Current Source
    3. 17.3 OA Registers
  20. 18GPAMP
    1. 18.1 GPAMP Overview
    2. 18.2 GPAMP Operation
      1. 18.2.1 Analog Core
      2. 18.2.2 Power Up Behavior
      3. 18.2.3 Inputs
      4. 18.2.4 Output
      5. 18.2.5 GPAMP Amplifier Modes
        1. 18.2.5.1 General-Purpose Mode
        2. 18.2.5.2 ADC Buffer Mode
        3. 18.2.5.3 Unity Gain Mode
      6. 18.2.6 Chopping
    3. 18.3 GPAMP Registers
  21. 19VREF
    1. 19.1 VREF Overview
    2. 19.2 VREF Operation
      1. 19.2.1 Internal Reference Generation
      2. 19.2.2 External Reference Input
      3. 19.2.3 Analog Peripheral Interface
    3. 19.3 VREF Registers
  22. 20LCD
    1. 20.1 LCD Introduction
      1. 20.1.1 LCD Operating Principle
      2. 20.1.2 Static Mode
      3. 20.1.3 2-Mux Mode
      4. 20.1.4 3-Mux Mode
      5. 20.1.5 4-Mux Mode
      6. 20.1.6 6-Mux Mode
      7. 20.1.7 8-Mux Mode
      8. 20.1.8 Introduction
      9. 20.1.9 LCD Waveforms
    2. 20.2 LCD Clocking
    3. 20.3 Voltage Generation
      1. 20.3.1  Mode 0 - Voltage Generation from external reference and external resistor divider
      2. 20.3.2  Mode 1 - Voltage Generation from AVDD and external resistor divider
      3. 20.3.3  Mode 2 - Voltage Generation from external reference and internal resistor divider
      4. 20.3.4  Mode 3 - Voltage Generation From AVDD and Internal Resistor Ladder
      5. 20.3.5  Mode 4 - Voltage Generation from charge pump with external supply
      6. 20.3.6  Mode 5 - Voltage Generation From Charge Pump With AVDD
      7. 20.3.7  Mode 6 - Voltage Generation From Charge Pump With External Reference on R13
      8. 20.3.8  Mode 7 - Voltage Generation From Charge Pump With Internal Reference on R13
      9. 20.3.9  Charge pump
      10. 20.3.10 Internal Reference Generation
    4. 20.4 Analog Mux
      1. 20.4.1 Static Mode
      2. 20.4.2 Non-Static 1/3 bias mode
      3. 20.4.3 Non-Static 1/4 bias mode
      4. 20.4.4 Low power mode switch controls
    5. 20.5 LCD Memory and output drive
      1. 20.5.1 LCD Memory organization
        1. 20.5.1.1 Memory Organization in Mux-1 to Mux-4 Modes
        2. 20.5.1.2 Memory Organization in Mux-5 to Mux-8 Modes
        3. 20.5.1.3 Configuring memory
        4. 20.5.1.4 Accessing memory and output drive
        5. 20.5.1.5 Blinking Override
    6. 20.6 IO Muxing
    7. 20.7 Interrupt Generation
    8. 20.8 Power Domains and Power Modes
    9. 20.9 LCD Registers
  23. 21UART
    1. 21.1 UART Overview
      1. 21.1.1 Purpose of the Peripheral
      2. 21.1.2 Features
      3. 21.1.3 Functional Block Diagram
    2. 21.2 UART Operation
      1. 21.2.1 Clock Control
      2. 21.2.2 Signal Descriptions
      3. 21.2.3 General Architecture and Protocol
        1. 21.2.3.1  Transmit Receive Logic
        2. 21.2.3.2  Bit Sampling
        3. 21.2.3.3  Majority Voting Feature
        4. 21.2.3.4  Baud Rate Generation
        5. 21.2.3.5  Data Transmission
        6. 21.2.3.6  Error and Status
        7. 21.2.3.7  Local Interconnect Network (LIN) Support
          1. 21.2.3.7.1 LIN Responder Transmission Delay
        8. 21.2.3.8  Flow Control
        9. 21.2.3.9  Idle-Line Multiprocessor
        10. 21.2.3.10 9-Bit UART Mode
        11. 21.2.3.11 RS485 Support
        12. 21.2.3.12 DALI Protocol
        13. 21.2.3.13 Manchester Encoding and Decoding
        14. 21.2.3.14 IrDA Encoding and Decoding
        15. 21.2.3.15 ISO7816 Smart Card Support
        16. 21.2.3.16 Address Detection
        17. 21.2.3.17 FIFO Operation
        18. 21.2.3.18 Loopback Operation
        19. 21.2.3.19 Glitch Suppression
      4. 21.2.4 Low Power Operation
      5. 21.2.5 Reset Considerations
      6. 21.2.6 Initialization
      7. 21.2.7 Interrupt and Events Support
        1. 21.2.7.1 CPU Interrupt Event Publisher (CPU_INT)
        2. 21.2.7.2 DMA Trigger Publisher (DMA_TRIG_RX, DMA_TRIG_TX)
      8. 21.2.8 Emulation Modes
    3. 21.3 UART Registers
  24. 22I2C
    1. 22.1 I2C Overview
      1. 22.1.1 Purpose of the Peripheral
      2. 22.1.2 Features
      3. 22.1.3 Functional Block Diagram
      4. 22.1.4 Environment and External Connections
    2. 22.2 I2C Operation
      1. 22.2.1 Clock Control
        1. 22.2.1.1 Clock Select and I2C Speed
        2. 22.2.1.2 Clock Startup
      2. 22.2.2 Signal Descriptions
      3. 22.2.3 General Architecture
        1. 22.2.3.1  I2C Bus Functional Overview
        2. 22.2.3.2  START and STOP Conditions
        3. 22.2.3.3  Data Format with 7-Bit Address
        4. 22.2.3.4  Acknowledge
        5. 22.2.3.5  Repeated Start
        6. 22.2.3.6  SCL Clock Low Timeout
        7. 22.2.3.7  Clock Stretching
        8. 22.2.3.8  Dual Address
        9. 22.2.3.9  Arbitration
        10. 22.2.3.10 Multiple Controller Mode
        11. 22.2.3.11 Glitch Suppression
        12. 22.2.3.12 FIFO operation
          1. 22.2.3.12.1 Flushing Stale Tx Data in Target Mode
        13. 22.2.3.13 Loopback mode
        14. 22.2.3.14 Burst Mode
        15. 22.2.3.15 DMA Operation
        16. 22.2.3.16 Low-Power Operation
      4. 22.2.4 Protocol Descriptions
        1. 22.2.4.1 I2C Controller Mode
          1. 22.2.4.1.1 Controller Configuration
          2. 22.2.4.1.2 Controller Mode Operation
          3. 22.2.4.1.3 Read On TX Empty
        2. 22.2.4.2 I2C Target Mode
          1. 22.2.4.2.1 Target Mode Operation
      5. 22.2.5 Reset Considerations
      6. 22.2.6 Initialization
      7. 22.2.7 Interrupt and Events Support
        1. 22.2.7.1 CPU Interrupt Event Publisher (CPU_INT)
        2. 22.2.7.2 DMA Trigger Publisher (DMA_TRIG1, DMA_TRIG0)
      8. 22.2.8 Emulation Modes
    3. 22.3 I2C Registers
  25. 23SPI
    1. 23.1 SPI Overview
      1. 23.1.1 Purpose of the Peripheral
      2. 23.1.2 Features
      3. 23.1.3 Functional Block Diagram
      4. 23.1.4 External Connections and Signal Descriptions
    2. 23.2 SPI Operation
      1. 23.2.1 Clock Control
      2. 23.2.2 General Architecture
        1. 23.2.2.1 Chip Select and Command Handling
          1. 23.2.2.1.1 Chip Select Control
          2. 23.2.2.1.2 Command Data Control
        2. 23.2.2.2 Data Format
        3. 23.2.2.3 Delayed data sampling
        4. 23.2.2.4 Clock Generation
        5. 23.2.2.5 FIFO Operation
        6. 23.2.2.6 Loopback mode
        7. 23.2.2.7 DMA Operation
        8. 23.2.2.8 Repeat Transfer mode
        9. 23.2.2.9 Low Power Mode
      3. 23.2.3 Protocol Descriptions
        1. 23.2.3.1 Motorola SPI Frame Format
        2. 23.2.3.2 Texas Instruments Synchronous Serial Frame Format
      4. 23.2.4 Reset Considerations
      5. 23.2.5 Initialization
      6. 23.2.6 Interrupt and Events Support
        1. 23.2.6.1 CPU Interrupt Event Publisher (CPU_INT)
        2. 23.2.6.2 DMA Trigger Publisher (DMA_TRIG_RX, DMA_TRIG_TX)
      7. 23.2.7 Emulation Modes
    3. 23.3 SPI Registers
  26. 24Timers (TIMx)
    1. 24.1 TIMx Overview
      1. 24.1.1 TIMG Overview
        1. 24.1.1.1 TIMG Features
        2. 24.1.1.2 Functional Block Diagram
      2. 24.1.2 TIMA Overview
        1. 24.1.2.1 TIMA Features
        2. 24.1.2.2 Functional Block Diagram
      3. 24.1.3 TIMx Instance Configuration
    2. 24.2 TIMx Operation
      1. 24.2.1  Timer Counter
        1. 24.2.1.1 Clock Source Select and Prescaler
          1. 24.2.1.1.1 Internal Clock and Prescaler
          2. 24.2.1.1.2 External Signal Trigger
        2. 24.2.1.2 Repeat Counter (TIMA only)
      2. 24.2.2  Counting Mode Control
        1. 24.2.2.1 One-shot and Periodic Modes
        2. 24.2.2.2 Down Counting Mode
        3. 24.2.2.3 Up/Down Counting Mode
        4. 24.2.2.4 Up Counting Mode
        5. 24.2.2.5 Phase Load (TIMA only)
      3. 24.2.3  Capture/Compare Module
        1. 24.2.3.1 Capture Mode
          1. 24.2.3.1.1 Input Selection, Counter Conditions, and Inversion
            1. 24.2.3.1.1.1 CCP Input Edge Synchronization
            2. 24.2.3.1.1.2 CCP Input Pulse Conditions
            3. 24.2.3.1.1.3 Counter Control Operation
            4. 24.2.3.1.1.4 CCP Input Filtering
            5. 24.2.3.1.1.5 Input Selection
          2. 24.2.3.1.2 Use Cases
            1. 24.2.3.1.2.1 Edge Time Capture
            2. 24.2.3.1.2.2 Period Capture
            3. 24.2.3.1.2.3 Pulse Width Capture
            4. 24.2.3.1.2.4 Combined Pulse Width and Period Time
          3. 24.2.3.1.3 QEI Mode (TIMG with QEI support only)
            1. 24.2.3.1.3.1 QEI With 2-Signal
            2. 24.2.3.1.3.2 QEI With Index Input
            3. 24.2.3.1.3.3 QEI Error Detection
          4. 24.2.3.1.4 Hall Input Mode (TIMG with QEI support only)
        2. 24.2.3.2 Compare Mode
          1. 24.2.3.2.1 Edge Count
      4. 24.2.4  Shadow Load and Shadow Compare
        1. 24.2.4.1 Shadow Load (TIMG4-7, TIMA only)
        2. 24.2.4.2 Shadow Compare (TIMG4-7, TIMG12-13, TIMA only)
      5. 24.2.5  Output Generator
        1. 24.2.5.1 Configuration
        2. 24.2.5.2 Use Cases
          1. 24.2.5.2.1 Edge-Aligned PWM
          2. 24.2.5.2.2 Center-Aligned PWM
          3. 24.2.5.2.3 Asymmetric PWM (TIMA only)
          4. 24.2.5.2.4 Complementary PWM With Deadband Insertion (TIMA only)
        3. 24.2.5.3 Forced Output
      6. 24.2.6  Fault Handler (TIMA only)
        1. 24.2.6.1 Fault Input Conditioning
        2. 24.2.6.2 Fault Input Sources
        3. 24.2.6.3 Counter Behavior With Fault Conditions
        4. 24.2.6.4 Output Behavior With Fault Conditions
      7. 24.2.7  Synchronization With Cross Trigger
        1. 24.2.7.1 Main Timer Cross Trigger Configuration
        2. 24.2.7.2 Secondary Timer Cross Trigger Configuration
      8. 24.2.8  Low Power Operation
      9. 24.2.9  Interrupt and Event Support
        1. 24.2.9.1 CPU Interrupt Event Publisher (CPU_INT)
        2. 24.2.9.2 Generic Event Publisher and Subscriber (GEN_EVENT0 and GEN_EVENT1)
        3. 24.2.9.3 Generic Subscriber Event Example (COMP to TIMx)
      10. 24.2.10 Debug Handler (TIMA Only)
    3. 24.3 TIMx Registers
  27. 25Low Frequency Subsystem (LFSS)
    1. 25.1  Overview
    2. 25.2  Clock System
    3. 25.3  LFSS Reset Using VBAT
    4. 25.4  Power Domains and Supply Detection
      1. 25.4.1 Startup When VBAT Powers on First
      2. 25.4.2 Startup when VDD powers on first
      3. 25.4.3 Behavior When VDD is Lost
      4. 25.4.4 Behavior when VBAT is lost
      5. 25.4.5 Behavior when the device goes into SHUTDOWN mode
      6. 25.4.6 Supercapacitor Charging Circuit
    5. 25.5  Real Time Counter (RTC_x)
    6. 25.6  Independent Watchdog Timer (IWDT)
    7. 25.7  Tamper Input and Output
      1. 25.7.1 IOMUX Mode
      2. 25.7.2 Tamper Mode
        1. 25.7.2.1 Tamper Event Detection
        2. 25.7.2.2 Timestamp Event Output
        3. 25.7.2.3 Heartbeat Generator
        4. 25.7.2.4 RTC Clock Output
    8. 25.8  Scratchpad Memory
    9. 25.9  Lock Function of RTC, TIO, and IWDT
    10. 25.10 LFSS Registers
  28. 26Low Frequency Subsystem (LFSS_B)
    1. 26.1 Overview
    2. 26.2 Clock System
    3. 26.3 LFSS Reset
    4. 26.4 Real Time Counter (RTC_x)
    5. 26.5 Independent Watchdog Timer (IWDT)
    6. 26.6 Lock Function of RTC and IWDT
    7. 26.7 LFSS Registers
  29. 27RTC
    1. 27.1 Overview
      1. 27.1.1 RTC Instances
    2. 27.2 Basic Operation
    3. 27.3 Configuration
      1. 27.3.1  Clocking
      2. 27.3.2  Reading and Writing to RTC Peripheral Registers
      3. 27.3.3  Binary vs. BCD
      4. 27.3.4  Leap Year Handling
      5. 27.3.5  Calendar Alarm Configuration
      6. 27.3.6  Interval Alarm Configuration
      7. 27.3.7  Periodic Alarm Configuration
      8. 27.3.8  Calibration
        1. 27.3.8.1 Crystal Offset Error
          1. 27.3.8.1.1 Offset Error Correction Mechanism
        2. 27.3.8.2 Crystal Temperature Error
          1. 27.3.8.2.1 Temperature Drift Correction Mechanism
      9. 27.3.9  RTC Prescaler Extension
      10. 27.3.10 RTC Timestamp Capture
      11. 27.3.11 RTC Events
        1. 27.3.11.1 CPU Interrupt Event Publisher (CPU_INT)
        2. 27.3.11.2 Generic Event Publisher (GEN_EVENT)
    4. 27.4 RTC Registers
  30. 28IWDT
    1. 28.1 734
    2. 28.2 IWDT Clock Configuration
    3. 28.3 IWDT Period Selection
    4. 28.4 Debug Behavior of the IWDT
    5. 28.5 IWDT Registers
  31. 29WWDT
    1. 29.1 WWDT Overview
      1. 29.1.1 Watchdog Mode
      2. 29.1.2 Interval Timer Mode
    2. 29.2 WWDT Operation
      1. 29.2.1 Mode Selection
      2. 29.2.2 Clock Configuration
      3. 29.2.3 Low-Power Mode Behavior
      4. 29.2.4 Debug Behavior
      5. 29.2.5 WWDT Events
        1. 29.2.5.1 CPU Interrupt Event Publisher (CPU_INT)
    3. 29.3 WWDT Registers
  32. 30Debug
    1. 30.1 DEBUGSS Overview
      1. 30.1.1 Debug Interconnect
      2. 30.1.2 Physical Interface
      3. 30.1.3 Debug Access Ports
    2. 30.2 DEBUGSS Operation
      1. 30.2.1 Debug Features
        1. 30.2.1.1 Processor Debug
          1. 30.2.1.1.1 Breakpoint Unit (BPU)
          2. 30.2.1.1.2 Data Watchpoint and Trace Unit (DWT)
        2. 30.2.1.2 Peripheral Debug
        3. 30.2.1.3 EnergyTrace Technology
      2. 30.2.2 Behavior in Low Power Modes
      3. 30.2.3 Restricting Debug Access
      4. 30.2.4 Mailbox (DSSM)
        1. 30.2.4.1 DSSM Events
          1. 30.2.4.1.1 CPU Interrupt Event (CPU_INT)
        2. 30.2.4.2 Reference
    3. 30.3 DEBUGSS Registers
  33. 31Revision History

2.9 SYSCTL_TYPEC Registers

Table 2-103 lists the memory-mapped registers for the SYSCTL_TYPEC registers. All register offset addresses not listed in Table 2-103 should be considered as reserved locations and the register contents should not be modified.

Table 2-103 SYSCTL_TYPEC Registers
OffsetAcronymRegister NameGroupSection
1020hIIDXSYSCTL interrupt indexGo
1028hIMASKSYSCTL interrupt maskGo
1030hRISSYSCTL raw interrupt statusGo
1038hMISSYSCTL masked interrupt statusGo
1040hISETSYSCTL interrupt setGo
1048hICLRSYSCTL interrupt clearGo
1050hNMIIIDXNMI interrupt indexGo
1060hNMIRISNMI raw interrupt statusGo
1070hNMIISETNMI interrupt setGo
1078hNMIICLRNMI interrupt clearGo
1100hSYSOSCCFGSYSOSC configurationGo
1104hMCLKCFGMain clock (MCLK) configurationGo
1108hHSCLKENHigh-speed clock (HSCLK) source enable/disableGo
1114hLFCLKCFGLow frequency crystal oscillator (LFXT) configurationGo
1138hGENCLKCFGGeneral clock configurationGo
113ChGENCLKENGeneral clock enable controlGo
1140hPMODECFGPower mode configurationGo
1150hFCCFrequency clock counter (FCC) countGo
1170hSYSOSCTRIMUSERSYSOSC user-specified trimGo
1178hSRAMBOUNDARYSRAM Write BoundaryGo
1180hSYSTEMCFGSystem configurationGo
1200hWRITELOCKSYSCTL register write lockoutGo
1204hCLKSTATUSClock module (CKM) statusGo
1208hSYSSTATUSSystem status informationGo
120ChDEDERRADDRMemory DED AddressGo
1220hRSTCAUSEReset causeGo
1300hRESETLEVELReset level for application-triggered reset commandGo
1304hRESETCMDExecute an application-triggered reset commandGo
1308hBORTHRESHOLDBOR threshold selectionGo
130ChBORCLRCMDSet the BOR thresholdGo
1310hSYSOSCFCLCTLSYSOSC frequency correction loop (FCL) ROSC enableGo
1314hLFXTCTLLFXT and LFCLK controlGo
1318hEXLFCTLLFCLK_IN and LFCLK controlGo
131ChSHDNIORELSHUTDOWN IO release controlGo
1320hEXRSTPINDisable the reset function of the NRST pinGo
1324hSYSSTATUSCLRClear sticky bits of SYSSTATUSGo
1328hSWDCFGDisable the SWD function on the SWD pinsGo
132ChFCCCMDFrequency clock counter start captureGo
1400hSHUTDNSTORE0Shutdown storage memory (byte 0)Go
1404hSHUTDNSTORE1Shutdown storage memory (byte 1)Go
1408hSHUTDNSTORE2Shutdown storage memory (byte 2)Go
140ChSHUTDNSTORE3Shutdown storage memory (byte 3)Go

Complex bit access types are encoded to fit into small table cells. Table 2-104 shows the codes that are used for access types in this section.

Table 2-104 SYSCTL_TYPEC Access Type Codes
Access TypeCodeDescription
Read Type
RRRead
RCR
C		Read
to Clear
Write Type
WWWrite
W1CW
1C		Write
1 to clear
W1SW
1S		Write
1 to set
Reset or Default Value
-nValue after reset or the default value

2.9.1 IIDX (Offset = 1020h) [Reset = 00000000h]

IIDX is shown in Figure 2-93 and described in Table 2-105.

Return to the Summary Table.

SYSCTL interrupt index

Figure 2-93 IIDX
31302928272625242322212019181716
RESERVED
R-0h
1514131211109876543210
RESERVEDSTAT
R-0hR-0h
Table 2-105 IIDX Field Descriptions
BitFieldTypeResetDescription
31-3RESERVEDR0h
2-0STATR0hThe SYSCTL interrupt index (IIDX) register generates a value corresponding to the highest priority pending interrupt source. This value may be used as an address offset for fast, deterministic handling in the interrupt service routine. A read of the IIDX register will clear the corresponding interrupt status in the RIS and MIS registers.
  • 0h = No interrupt pending
  • 1h = LFOSCGOOD interrupt pending
  • 2h = 2
  • 3h = 3
  • 4h = 4

2.9.2 IMASK (Offset = 1028h) [Reset = 00000000h]

IMASK is shown in Figure 2-94 and described in Table 2-106.

Return to the Summary Table.

SYSCTL interrupt mask

Figure 2-94 IMASK
3130292827262524
RESERVED
R-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVED
R-0h
76543210
RESERVEDLFXTGOODFLASHSECANACLKERRLFOSCGOOD
R-0hR/W-0hR/W-0hR/W-0hR/W-0h
Table 2-106 IMASK Field Descriptions
BitFieldTypeResetDescription
31-4RESERVEDR0h
3LFXTGOODR/W0hLFXT GOOD
  • 0h = 0
  • 1h = 1
2FLASHSECR/W0hFlash Single Error Correct
  • 0h = 0
  • 1h = 1
1ANACLKERRR/W0hAnalog Clocking Consistency Error
  • 0h = 0
  • 1h = 1
0LFOSCGOODR/W0hEnable or disable the LFOSCGOOD interrupt. LFOSCGOOD indicates that the LFOSC has started successfully.
  • 0h = Interrupt disabled
  • 1h = Interrupt enabled

2.9.3 RIS (Offset = 1030h) [Reset = 00000000h]

RIS is shown in Figure 2-95 and described in Table 2-107.

Return to the Summary Table.

SYSCTL raw interrupt status

Figure 2-95 RIS
3130292827262524
RESERVED
R-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVED
R-0h
76543210
RESERVEDLFXTGOODFLASHSECANACLKERRLFOSCGOOD
R-0hR-0hR-0hR-0hR-0h
Table 2-107 RIS Field Descriptions
BitFieldTypeResetDescription
31-4RESERVEDR0h
3LFXTGOODR0hLFXT GOOD
  • 0h = 0
  • 1h = 1
2FLASHSECR0hFlash Single Error Correct
  • 0h = 0
  • 1h = 1
1ANACLKERRR0hAnalog Clocking Consistency Error
  • 0h = 0
  • 1h = 1
0LFOSCGOODR0hRaw status of the LFOSCGOOD interrupt.
  • 0h = No interrupt pending
  • 1h = Interrupt pending

2.9.4 MIS (Offset = 1038h) [Reset = 00000000h]

MIS is shown in Figure 2-96 and described in Table 2-108.

Return to the Summary Table.

SYSCTL masked interrupt status

Figure 2-96 MIS
3130292827262524
RESERVED
R-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVED
R-0h
76543210
RESERVEDLFXTGOODFLASHSECANACLKERRLFOSCGOOD
R-0hR-0hR-0hR-0hR-0h
Table 2-108 MIS Field Descriptions
BitFieldTypeResetDescription
31-4RESERVEDR0h
3LFXTGOODR0hLFXT GOOD
  • 0h = 0
  • 1h = 1
2FLASHSECR0hFlash Single Error Correct
  • 0h = 0
  • 1h = 1
1ANACLKERRR0hAnalog Clocking Consistency Error
  • 0h = 0
  • 1h = 1
0LFOSCGOODR0hMasked status of the LFOSCGOOD interrupt.
  • 0h = No interrupt pending
  • 1h = Interrupt pending

2.9.5 ISET (Offset = 1040h) [Reset = 00000000h]

ISET is shown in Figure 2-97 and described in Table 2-109.

Return to the Summary Table.

SYSCTL interrupt set

Figure 2-97 ISET
3130292827262524
RESERVED
R-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVED
R-0h
76543210
RESERVEDLFXTGOODFLASHSECANACLKERRLFOSCGOOD
R-0hW1S-0hW1S-0hW1S-0hW1S-0h
Table 2-109 ISET Field Descriptions
BitFieldTypeResetDescription
31-4RESERVEDR0h
3LFXTGOODW1S0hLFXT GOOD
  • 0h = 0
  • 1h = 1
2FLASHSECW1S0hFlash Single Error Correct
  • 0h = 0
  • 1h = 1
1ANACLKERRW1S0hAnalog Clocking Consistency Error
  • 0h = 0
  • 1h = 1
0LFOSCGOODW1S0hSet the LFOSCGOOD interrupt.
  • 0h = Writing 0h hs no effect
  • 1h = Set interrupt

2.9.6 ICLR (Offset = 1048h) [Reset = 00000000h]

ICLR is shown in Figure 2-98 and described in Table 2-110.

Return to the Summary Table.

SYSCTL interrupt clear

Figure 2-98 ICLR
3130292827262524
RESERVED
R-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVED
R-0h
76543210
RESERVEDLFXTGOODFLASHSECANACLKERRLFOSCGOOD
R-0hW1C-0hW1C-0hW1C-0hW1C-0h
Table 2-110 ICLR Field Descriptions
BitFieldTypeResetDescription
31-4RESERVEDR0h
3LFXTGOODW1C0hLFXT GOOD
  • 0h = 0
  • 1h = 1
2FLASHSECW1C0hFlash Single Error Correct
  • 0h = 0
  • 1h = 1
1ANACLKERRW1C0hAnalog Clocking Consistency Error
  • 0h = 0
  • 1h = 1
0LFOSCGOODW1C0hClear the LFOSCGOOD interrupt.
  • 0h = Writing 0h has no effect
  • 1h = Clear interrupt

2.9.7 NMIIIDX (Offset = 1050h) [Reset = 00000000h]

NMIIIDX is shown in Figure 2-99 and described in Table 2-111.

Return to the Summary Table.

NMI interrupt index

Figure 2-99 NMIIIDX
31302928272625242322212019181716
RESERVED
R-0h
1514131211109876543210
RESERVEDSTAT
R-0hR-0h
Table 2-111 NMIIIDX Field Descriptions
BitFieldTypeResetDescription
31-3RESERVEDR0h
2-0STATR0hThe NMI interrupt index (NMIIIDX) register generates a value corresponding to the highest priority pending NMI source. This value may be used as an address offset for fast, deterministic handling in the NMI service routine. A read of the NMIIIDX register will clear the corresponding interrupt status in the NMIRIS register.
  • 0h = No NMI pending
  • 1h = BOR Threshold NMI pending
  • 2h = 2
  • 3h = 3
  • 4h = 4

2.9.8 NMIRIS (Offset = 1060h) [Reset = 00000000h]

NMIRIS is shown in Figure 2-100 and described in Table 2-112.

Return to the Summary Table.

NMI raw interrupt status

Figure 2-100 NMIRIS
3130292827262524
RESERVED
R-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVED
R-0h
76543210
RESERVEDFLASHDEDLFCLKFAILWWDT0BORLVL
R-0hR-0hR-0hR-0hR-0h
Table 2-112 NMIRIS Field Descriptions
BitFieldTypeResetDescription
31-4RESERVEDR0h
3FLASHDEDR0hFlash Double Error Detect
  • 0h = 0
  • 1h = 1
2LFCLKFAILR0hLFXT-EXLF Monitor Fail
  • 0h = 0
  • 1h = 1
1WWDT0R0hWatch Dog 0 Fault
  • 0h = 0
  • 1h = 1
0BORLVLR0hRaw status of the BORLVL NMI
  • 0h = No interrupt pending
  • 1h = Interrupt pending

2.9.9 NMIISET (Offset = 1070h) [Reset = 00000000h]

NMIISET is shown in Figure 2-101 and described in Table 2-113.

Return to the Summary Table.

NMI interrupt set

Figure 2-101 NMIISET
3130292827262524
RESERVED
R-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVED
R-0h
76543210
RESERVEDFLASHDEDLFCLKFAILWWDT0BORLVL
R-0hW1S-0hW1S-0hW1S-0hW1S-0h
Table 2-113 NMIISET Field Descriptions
BitFieldTypeResetDescription
31-4RESERVEDR0h
3FLASHDEDW1S0hFlash Double Error Detect
  • 0h = 0
  • 1h = 1
2LFCLKFAILW1S0hLFXT-EXLF Monitor Fail
  • 0h = 0
  • 1h = 1
1WWDT0W1S0hWatch Dog 0 Fault
  • 0h = 0
  • 1h = 1
0BORLVLW1S0hSet the BORLVL NMI
  • 0h = Writing 0h hs no effect
  • 1h = Set interrupt

2.9.10 NMIICLR (Offset = 1078h) [Reset = 00000000h]

NMIICLR is shown in Figure 2-102 and described in Table 2-114.

Return to the Summary Table.

NMI interrupt clear

Figure 2-102 NMIICLR
3130292827262524
RESERVED
R-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVED
R-0h
76543210
RESERVEDFLASHDEDLFCLKFAILWWDT0BORLVL
R-0hW1C-0hW1C-0hW1C-0hW1C-0h
Table 2-114 NMIICLR Field Descriptions
BitFieldTypeResetDescription
31-4RESERVEDR0h
3FLASHDEDW1C0hFlash Double Error Detect
  • 0h = 0
  • 1h = 1
2LFCLKFAILW1C0hLFXT-EXLF Monitor Fail
  • 0h = 0
  • 1h = 1
1WWDT0W1C0hWatch Dog 0 Fault
  • 0h = 0
  • 1h = 1
0BORLVLW1C0hClr the BORLVL NMI
  • 0h = Writing 0h hs no effect
  • 1h = Clear interrupt

2.9.11 SYSOSCCFG (Offset = 1100h) [Reset = 0002XXXXh]

SYSOSCCFG is shown in Figure 2-103 and described in Table 2-115.

Return to the Summary Table.

SYSOSC configuration

Figure 2-103 SYSOSCCFG
3130292827262524
RESERVED
R-0h
2322212019181716
RESERVEDFASTCPUEVENTBLOCKASYNCALL
R-0hR/W-1hR/W-0h
15141312111098
RESERVEDDISABLEDISABLESTOPUSE4MHZSTOP
R-0hR/W-0hR/W-0hR/W-0h
76543210
RESERVEDFREQ
R-0hR/W-0h
Table 2-115 SYSOSCCFG Field Descriptions
BitFieldTypeResetDescription
31-18RESERVEDR0h
17FASTCPUEVENTR/W1hFASTCPUEVENT may be used to assert a fast clock request when an interrupt is asserted to the CPU, reducing interrupt latency.
  • 0h = An interrupt to the CPU will not assert a fast clock request
  • 1h = An interrupt to the CPU will assert a fast clock request
16BLOCKASYNCALLR/W0hBLOCKASYNCALL may be used to mask block all asynchronous fast clock requests, preventing hardware from dynamically changing the active clock configuration when operating in a given mode.
  • 0h = Asynchronous fast clock requests are controlled by the requesting peripheral
  • 1h = All asynchronous fast clock requests are blocked
15-11RESERVEDR0h
10DISABLER/W0hDISABLE sets the SYSOSC enable/disable policy. SYSOSC may be powered off in RUN, SLEEP, and STOP modes to reduce power consumption. When SYSOSC is disabled, MCLK and ULPCLK are sourced from LFCLK.
  • 0h = Do not disable SYSOSC
  • 1h = Disable SYSOSC immediately and source MCLK and ULPCLK from LFCLK
9DISABLESTOPR/W0hDISABLESTOP sets the SYSOSC stop mode enable/disable policy. When operating in STOP mode, the SYSOSC may be automatically disabled. When set, ULPCLK will run from LFCLK in STOP mode and SYSOSC will be disabled to reduce power consumption.
  • 0h = Do not disable SYSOSC in STOP mode
  • 1h = Disable SYSOSC in STOP mode and source ULPCLK from LFCLK
8USE4MHZSTOPR/W0hUSE4MHZSTOP sets the SYSOSC stop mode frequency policy. When entering STOP mode, the SYSOSC frequency may be automatically switched to 4MHz to reduce SYSOSC power consumption.
  • 0h = Do not gear shift the SYSOSC to 4MHz in STOP mode
  • 1h = Gear shift SYSOSC to 4MHz in STOP mode
7-2RESERVEDR0h
1-0FREQR/W0hTarget operating frequency for the system oscillator (SYSOSC)
  • 0h = Base frequency (32MHz)
  • 1h = Low frequency (4MHz)
  • 2h = User-trimmed frequency (16 or 24 MHz)

2.9.12 MCLKCFG (Offset = 1104h) [Reset = 000XX2X0h]

MCLKCFG is shown in Figure 2-104 and described in Table 2-116.

Return to the Summary Table.

Main clock (MCLK) configuration

Figure 2-104 MCLKCFG
3130292827262524
RESERVED
R-0h
2322212019181716
RESERVEDMCLKDEADCHKSTOPCLKSTBYUSELFCLKRESERVEDUSEHSCLK
R-0hR/W-0hR/W-0hR/W-0hR-0hR/W-0h
15141312111098
RESERVEDUSEMFTICKFLASHWAIT
R-0hR/W-0hR/W-2h
76543210
RESERVEDMDIV
R-0hR/W-0h
Table 2-116 MCLKCFG Field Descriptions
BitFieldTypeResetDescription
31-23RESERVEDR0h
22MCLKDEADCHKR/W0hMCLKDEADCHK enables or disables the continuous MCLK dead check monitor. LFCLK must be running before MCLKDEADCHK is enabled.
  • 0h = The MCLK dead check monitor is disabled
  • 1h = The MCLK dead check monitor is enabled
21STOPCLKSTBYR/W0hSTOPCLKSTBY sets the STANDBY mode policy (STANDBY0 or STANDBY1). When set, ULPCLK and LFCLK are disabled to all peripherals in STANDBY mode, with the exception of TIMG0 and TIMG1 which continue to run. Wake-up is only possible via an asynchronous fast clock request.
  • 0h = ULPCLK/LFCLK runs to all PD0 peripherals in STANDBY mode
  • 1h = ULPCLK/LFCLK is disabled to all peripherals in STANDBY mode except TIMG0 and TIMG1
20USELFCLKR/W0hUSELFCLK sets the MCLK source policy. Set USELFCLK to use LFCLK as the MCLK source. Note that setting USELFCLK does not disable SYSOSC, and SYSOSC remains available for direct use by analog modules.
  • 0h = MCLK will not use the low frequency clock (LFCLK)
  • 1h = MCLK will use the low frequency clock (LFCLK)
19-17RESERVEDR0h
16USEHSCLKR/W0hUSEHSCLK, together with USELFCLK, sets the MCLK source policy. Set USEHSCLK to use HSCLK (HFCLK or SYSPLL) as the MCLK source in RUN and SLEEP modes.
  • 0h = MCLK will not use the high speed clock (HSCLK)
  • 1h = MCLK will use the high speed clock (HSCLK) in RUN and SLEEP mode
15-13RESERVEDR0h
12USEMFTICKR/W0hUSEMFTICK specifies whether the 4MHz constant-rate clock (MFCLK) to peripherals is enabled or disabled. When enabled, MDIV must be disabled (set to 0h=/1).
  • 0h = The 4MHz rate MFCLK to peripherals is enabled
  • 1h = The 4MHz rate MFCLK to peripherals is enabled.
11-8FLASHWAITR/W2hFLASHWAIT specifies the number of flash wait states when MCLK is sourced from HSCLK. FLASHWAIT has no effect when MCLK is sourced from SYSOSC or LFCLK.
  • 0h = No flash wait states are applied
  • 1h = One flash wait state is applied
  • 2h = 2 flash wait states are applied
7-4RESERVEDR0h
3-0MDIVR/W0hMDIV may be used to divide the MCLK frequency when MCLK is sourced from SYSOSC. MDIV=0h corresponds to /1 (no divider). MDIV=1h corresponds to /2 (divide-by-2). MDIV=Fh corresponds to /16 (divide-by-16). MDIV may be set between /1 and /16 on an integer basis.

2.9.13 HSCLKEN (Offset = 1108h) [Reset = 0000XXXXh]

HSCLKEN is shown in Figure 2-105 and described in Table 2-117.

Return to the Summary Table.

High-speed clock (HSCLK) source enable/disable

Figure 2-105 HSCLKEN
3130292827262524
RESERVED
R-0h
2322212019181716
RESERVEDUSEEXTHFCLK
R-0hR/W-0h
15141312111098
RESERVED
R-0h
76543210
RESERVED
R-0h
Table 2-117 HSCLKEN Field Descriptions
BitFieldTypeResetDescription
31-17RESERVEDR0h
16USEEXTHFCLKR/W0hUSEEXTHFCLK selects the HFCLK_IN digital clock input to be the source for HFCLK. When disabled, HFXT is the HFCLK source and HFXTEN may be set. Do not set HFXTEN and USEEXTHFCLK simultaneously.
  • 0h = Use HFXT as the HFCLK source
  • 1h = Use the HFCLK_IN digital clock input as the HFCLK source
15-0RESERVEDR0h

2.9.14 LFCLKCFG (Offset = 1114h) [Reset = 000000XXh]

LFCLKCFG is shown in Figure 2-106 and described in Table 2-118.

Return to the Summary Table.

Low frequency crystal oscillator (LFXT) configuration

Figure 2-106 LFCLKCFG
3130292827262524
RESERVED
R-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVEDLOWCAP
R-0hR/W-0h
76543210
RESERVEDMONITORRESERVEDXT1DRIVE
R-0hR/W-0hR-0hR/W-3h
Table 2-118 LFCLKCFG Field Descriptions
BitFieldTypeResetDescription
31-9RESERVEDR0h
8LOWCAPR/W0hLOWCAP controls the low-power LFXT mode. When the LFXT load capacitance is less than 3pf, LOWCAP may be set for reduced power consumption.
  • 0h = LFXT low capacitance mode is disabled
  • 1h = LFXT low capacitance mode is enabled
7-5RESERVEDR0h
4MONITORR/W0hMONITOR enables or disables the LFCLK monitor, which continuously checks LFXT or LFCLK_IN for a clock stuck fault.
  • 0h = Clock monitor is disabled
  • 1h = Clock monitor is enabled
3-2RESERVEDR0h
1-0XT1DRIVER/W3hXT1DRIVE selects the low frequency crystal oscillator (LFXT) drive strength.
  • 0h = Lowest drive and current
  • 1h = Lower drive and current
  • 2h = Higher drive and current
  • 3h = Highest drive and current

2.9.15 GENCLKCFG (Offset = 1138h) [Reset = 00000X0Xh]

GENCLKCFG is shown in Figure 2-107 and described in Table 2-119.

Return to the Summary Table.

General clock configuration

Figure 2-107 GENCLKCFG
3130292827262524
RESERVEDFCCLFCLKSRCFCCTRIGCNT
R-0hR/W-0hR/W-0h
2322212019181716
ANACPUMPCFGFCCLVLTRIGFCCTRIGSRCFCCSELCLK
R/W-0hR/W-0hR/W-0hR/W-0h
15141312111098
HFCLK4MFPCLKDIVRESERVEDMFPCLKSRCRESERVED
R/W-0hR-0hR/W-0hR-0h
76543210
EXCLKDIVENEXCLKDIVVALRESERVEDEXCLKSRC
R/W-0hR/W-0hR-0hR/W-0h
Table 2-119 GENCLKCFG Field Descriptions
BitFieldTypeResetDescription
31-30RESERVEDR0h
29FCCLFCLKSRCR/W0hFCCLFCLKSRC selects between SYSTEM LFCLK and EXTERNAL SOURCED LFCLK.
28-24FCCTRIGCNTR/W0hFCCTRIGCNT specifies the number of trigger clock periods in the trigger window. FCCTRIGCNT=0h (one trigger clock period) up to 1Fh (32 trigger clock periods) may be specified.
23-22ANACPUMPCFGR/W0hANACPUMPCFG selects the analog mux charge pump (VBOOST) enable method.
  • 0h = VBOOST is enabled on request from a COMP, GPAMP, or OPA
  • 1h = VBOOST is enabled when the device is in RUN or SLEEP mode, or when a COMP/GPAMP/OPA is enabled
  • 2h = VBOOST is always enabled
21FCCLVLTRIGR/W0hFCCLVLTRIG selects the frequency clock counter (FCC) trigger mode.
  • 0h = Rising edge to rising edge triggered
  • 1h = Level triggered
20FCCTRIGSRCR/W0hFCCTRIGSRC selects the frequency clock counter (FCC) trigger source.
  • 0h = FCC trigger is the external pin
  • 1h = FCC trigger is the LFCLK
19-16FCCSELCLKR/W0hFCCSELCLK selectes the frequency clock counter (FCC) clock source.
  • 0h = FCC clock is MCLK
  • 1h = FCC clock is SYSOSC
  • 2h = FCC clock is HFCLK
  • 3h = FCC clock is the CLK_OUT selection
  • 7h = FCC clock is the FCCIN external input
15-12HFCLK4MFPCLKDIVR/W0hHFCLK4MFPCLKDIV selects the divider applied to HFCLK when HFCLK is used as the MFPCLK source. Integer dividers from /1 to /16 may be selected.
  • 0h = HFCLK is not divided before being used for MFPCLK
  • 1h = HFCLK is divided by 2 before being used for MFPCLK
  • 2h = HFCLK is divided by 3 before being used for MFPCLK
  • 3h = HFCLK is divided by 4 before being used for MFPCLK
  • 4h = HFCLK is divided by 5 before being used for MFPCLK
  • 5h = HFCLK is divided by 6 before being used for MFPCLK
  • 6h = HFCLK is divided by 7 before being used for MFPCLK
  • 7h = HFCLK is divided by 8 before being used for MFPCLK
  • 8h = HFCLK is divided by 9 before being used for MFPCLK
  • 9h = HFCLK is divided by 10 before being used for MFPCLK
  • Ah = HFCLK is divided by 11 before being used for MFPCLK
  • Bh = HFCLK is divided by 12 before being used for MFPCLK
  • Ch = HFCLK is divided by 13 before being used for MFPCLK
  • Dh = HFCLK is divided by 14 before being used for MFPCLK
  • Eh = HFCLK is divided by 15 before being used for MFPCLK
  • Fh = HFCLK is divided by 16 before being used for MFPCLK
11-10RESERVEDR0h
9MFPCLKSRCR/W0hMFPCLKSRC selects the MFPCLK (middle frequency precision clock) source.
  • 0h = MFPCLK is sourced from SYSOSC
  • 1h = MFPCLK is sourced from HFCLK
8RESERVEDR0h
7EXCLKDIVENR/W0hEXCLKDIVEN enables or disables the divider function of the CLK_OUT external clock output block.
  • 0h = CLock divider is disabled (passthrough, EXCLKDIVVAL is not applied)
  • 1h = Clock divider is enabled (EXCLKDIVVAL is applied)
6-4EXCLKDIVVALR/W0hEXCLKDIVVAL selects the divider value for the divider in the CLK_OUT external clock output block.
  • 0h = CLK_OUT source is divided by 2
  • 1h = CLK_OUT source is divided by 4
  • 2h = CLK_OUT source is divided by 6
  • 3h = CLK_OUT source is divided by 8
  • 4h = CLK_OUT source is divided by 10
  • 5h = CLK_OUT source is divided by 12
  • 6h = CLK_OUT source is divided by 14
  • 7h = CLK_OUT source is divided by 16
3RESERVEDR0h
2-0EXCLKSRCR/W0hEXCLKSRC selects the source for the CLK_OUT external clock output block. ULPCLK and MFPCLK require the CLK_OUT divider (EXCLKDIVEN) to be enabled
  • 0h = CLK_OUT is SYSOSC
  • 1h = CLK_OUT is ULPCLK (EXCLKDIVEN must be enabled)
  • 2h = CLK_OUT is LFCLK
  • 3h = CLK_OUT is MFPCLK (EXCLKDIVEN must be enabled)
  • 4h = CLK_OUT is HFCLK

2.9.16 GENCLKEN (Offset = 113Ch) [Reset = 0000000Xh]

GENCLKEN is shown in Figure 2-108 and described in Table 2-120.

Return to the Summary Table.

General clock enable control

Figure 2-108 GENCLKEN
3130292827262524
RESERVED
R-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVED
R-0h
76543210
RESERVEDMFPCLKENRESERVEDEXCLKEN
R-0hR/W-0hR-0hR/W-0h
Table 2-120 GENCLKEN Field Descriptions
BitFieldTypeResetDescription
31-5RESERVEDR0h
4MFPCLKENR/W0hMFPCLKEN enables the middle frequency precision clock (MFPCLK).
  • 0h = MFPCLK is disabled
  • 1h = MFPCLK is enabled
3-1RESERVEDR0h
0EXCLKENR/W0hEXCLKEN enables the CLK_OUT external clock output block.
  • 0h = CLK_OUT block is disabled
  • 1h = CLK_OUT block is enabled

2.9.17 PMODECFG (Offset = 1140h) [Reset = 00000000h]

PMODECFG is shown in Figure 2-109 and described in Table 2-121.

Return to the Summary Table.

Power mode configuration

Figure 2-109 PMODECFG
31302928272625242322212019181716
RESERVED
R-0h
1514131211109876543210
RESERVEDDSLEEP
R-0hR/W-0h
Table 2-121 PMODECFG Field Descriptions
BitFieldTypeResetDescription
31-2RESERVEDR0h
1-0DSLEEPR/W0hDSLEEP selects the operating mode to enter upon a DEEPSLEEP request from the CPU.
  • 0h = STOP mode is entered
  • 1h = STANDBY mode is entered
  • 2h = SHUTDOWN mode is entered
  • 3h = Reserved

2.9.18 FCC (Offset = 1150h) [Reset = 00000000h]

FCC is shown in Figure 2-110 and described in Table 2-122.

Return to the Summary Table.

Frequency clock counter (FCC) count

Figure 2-110 FCC
313029282726252423222120191817161514131211109876543210
RESERVEDDATA
R-0hR-0h
Table 2-122 FCC Field Descriptions
BitFieldTypeResetDescription
31-22RESERVEDR0h
21-0DATAR0hFrequency clock counter (FCC) count value.

2.9.19 SYSOSCTRIMUSER (Offset = 1170h) [Reset = 0000X0XXh]

SYSOSCTRIMUSER is shown in Figure 2-111 and described in Table 2-123.

Return to the Summary Table.

SYSOSC user-specified trim

Figure 2-111 SYSOSCTRIMUSER
3130292827262524
RESERVEDRDIV
R-0hR/W-0h
2322212019181716
RDIVRESFINE
R/W-0hR/W-0h
15141312111098
RESERVEDRESCOARSE
R-0hR/W-0h
76543210
RESERVEDCAPRESERVEDFREQ
R-0hR/W-0hR-0hR/W-0h
Table 2-123 SYSOSCTRIMUSER Field Descriptions
BitFieldTypeResetDescription
31-29RESERVEDR0h
28-20RDIVR/W0hRDIV specifies the frequency correction loop (FCL) resistor trim. This value changes with the target frequency.
19-16RESFINER/W0hRESFINE specifies the resister fine trim. This value changes with the target frequency.
15-14RESERVEDR0h
13-8RESCOARSER/W0hRESCOARSE specifies the resister coarse trim. This value changes with the target frequency.
7RESERVEDR0h
6-4CAPR/W0hCAP specifies the SYSOSC capacitor trim. This value changes with the target frequency.
3-2RESERVEDR0h
1-0FREQR/W0hFREQ specifies the target user-trimmed frequency for SYSOSC.
  • 0h = Reserved
  • 1h = 16MHz user frequency
  • 2h = 24MHz user frequency
  • 3h = Reserved

2.9.20 SRAMBOUNDARY (Offset = 1178h) [Reset = 000000XXh]

SRAMBOUNDARY is shown in Figure 2-112 and described in Table 2-124.

Return to the Summary Table.

SRAM Write Boundary

Figure 2-112 SRAMBOUNDARY
313029282726252423222120191817161514131211109876543210
RESERVEDADDRRESERVED
R-0hR/W-0hR-0h
Table 2-124 SRAMBOUNDARY Field Descriptions
BitFieldTypeResetDescription
31-20RESERVEDR0h
19-5ADDRR/W0hSRAM boundary configuration. The value configured into this acts such that: SRAM accesses to addresses less than or equal value will be RW only. SRAM accesses to addresses greater than value will be RX only. Value of 0 is not valid (system will have no stack). If set to 0, the system acts as if the entire SRAM is RWX. Any non-zero value can be configured, including a value = SRAM size.
4-0RESERVEDR0h

2.9.21 SYSTEMCFG (Offset = 1180h) [Reset = 00XXXXXXh]

SYSTEMCFG is shown in Figure 2-113 and described in Table 2-125.

Return to the Summary Table.

System configuration

Figure 2-113 SYSTEMCFG
3130292827262524
KEY
W-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVED
R-0h
76543210
RESERVEDFLASHECCRSTDISRESERVEDWWDTLP0RSTDIS
R-0hR/W-1hR-0hR/W-0h
Table 2-125 SYSTEMCFG Field Descriptions
BitFieldTypeResetDescription
31-24KEYW0hThe key value of 1Bh (27) must be written to KEY together with contents to be updated. Reads as 0
  • 1Bh = Issue write
23-3RESERVEDR0h
2FLASHECCRSTDISR/W1hFLASHECCRSTDIS specifies whether a flash ECC double error detect (DED) will trigger a SYSRST or an NMI.
  • 0h = Flash ECC DED will trigger a SYSRST
  • 1h = Flash ECC DED will trigger a NMI
1RESERVEDR0h
0WWDTLP0RSTDISR/W0hWWDTLP0RSTDIS specifies whether a WWDT Error Event will trigger a BOOTRST or an NMI.
  • 0h = WWDTLP0 Error Event will trigger a BOOTRST
  • 1h = WWDTLP0 Error Event will trigger an NMI

2.9.22 WRITELOCK (Offset = 1200h) [Reset = 00000000h]

WRITELOCK is shown in Figure 2-114 and described in Table 2-126.

Return to the Summary Table.

SYSCTL register write lockout

Figure 2-114 WRITELOCK
3130292827262524
RESERVED
R-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVED
R-0h
76543210
RESERVEDACTIVE
R-0hR/W-0h
Table 2-126 WRITELOCK Field Descriptions
BitFieldTypeResetDescription
31-1RESERVEDR0h
0ACTIVER/W0hACTIVE controls whether critical SYSCTL registers are write protected or not.
  • 0h = Allow writes to lockable registers
  • 1h = Disallow writes to lockable registers

2.9.23 CLKSTATUS (Offset = 1204h) [Reset = XXXXXXXXh]

CLKSTATUS is shown in Figure 2-115 and described in Table 2-127.

Return to the Summary Table.

Clock module (CKM) status

Figure 2-115 CLKSTATUS
3130292827262524
ANACLKERRRESERVEDFCCDONEFCLMODE
R-0hR-0hR-0hR-0h
2322212019181716
LFCLKFAILRESERVEDCURMCLKSELRESERVED
R-0hR-0hR-0hR-0h
15141312111098
RESERVEDLFOSCGOODLFXTGOODRESERVED
R-0hR-0hR-0hR-0h
76543210
LFCLKMUXRESERVEDHSCLKMUXRESERVEDSYSOSCFREQ
R-0hR-0hR-0hR-0hR-0h
Table 2-127 CLKSTATUS Field Descriptions
BitFieldTypeResetDescription
31ANACLKERRR0hANACLKERR is set when the device clock configuration does not support an enabled analog peripheral mode and the analog peripheral may not be functioning as expected.
  • 0h = No analog clock errors detected
  • 1h = Analog clock error detected
30-26RESERVEDR0h
25FCCDONER0hFCCDONE indicates when a frequency clock counter capture is complete.
  • 0h = FCC capture is not done
  • 1h = FCC capture is done
24FCLMODER0hFCLMODE indicates if the SYSOSC frequency correction loop (FCL) is enabled.
  • 0h = SYSOSC FCL is disabled
  • 1h = SYSOSC FCL is enabled
23LFCLKFAILR0hLFCLKFAIL indicates when the continous LFCLK monitor detects a LFXT or LFCLK_IN clock stuck failure.
  • 0h = No LFCLK fault detected
  • 1h = LFCLK stuck fault detected
22-18RESERVEDR0h
17CURMCLKSELR0hCURMCLKSEL indicates if MCLK is currently sourced from LFCLK.
  • 0h = MCLK is not sourced from LFCLK
  • 1h = MCLK is sourced from LFCLK
16-12RESERVEDR0h
11LFOSCGOODR0hLFOSCGOOD indicates when the LFOSC startup has completed and the LFOSC is ready for use.
  • 0h = LFOSC is not ready
  • 1h = LFOSC is ready
10LFXTGOODR0hLFXTGOOD indicates if the LFXT started correctly. When the LFXT is started, LFXTGOOD is cleared by hardware. After the startup settling time has expired, the LFXT status is tested. If the LFXT started successfully the LFXTGOOD bit is set, else it is left cleared.
  • 0h = LFXT did not start correctly
  • 1h = LFXT started correctly
9-8RESERVEDR0h
7-6LFCLKMUXR0hLFCLKMUX indicates if LFCLK is sourced from the internal LFOSC, the low frequency crystal (LFXT), or the LFCLK_IN digital clock input.
  • 0h = LFCLK is sourced from the internal LFOSC
  • 1h = LFCLK is sourced from the LFXT (crystal)
  • 2h = LFCLK is sourced from LFCLK_IN (external digital clock input)
5RESERVEDR0h
4HSCLKMUXR0hHSCLKMUX indicates if MCLK is currently sourced from the high-speed clock (HSCLK).
  • 0h = MCLK is not sourced from HSCLK
  • 1h = MCLK is sourced from HSCLK
3-2RESERVEDR0h
1-0SYSOSCFREQR0hSYSOSCFREQ indicates the current SYSOSC operating frequency.
  • 0h = SYSOSC is at base frequency (32MHz)
  • 1h = SYSOSC is at low frequency (4MHz)
  • 2h = SYSOSC is at the user-trimmed frequency (16 or 24MHz)
  • 3h = Reserved

2.9.24 SYSSTATUS (Offset = 1208h) [Reset = XXXX0XX0h]

SYSSTATUS is shown in Figure 2-116 and described in Table 2-128.

Return to the Summary Table.

System status information

Figure 2-116 SYSSTATUS
3130292827262524
REBOOTATTEMPTSRESERVED
R-0hR-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVEDSHDNIOLOCKSWDCFGDISEXTRSTPINDISRESERVED
R-0hR-0hR-0hR-0hR-0h
76543210
RESERVEDPMUIREFGOODANACPUMPGOODBORLVLBORCURTHRESHOLDFLASHSECFLASHDED
R-0hR-0hR-0hR-0hR-0hR-0hR-0h
Table 2-128 SYSSTATUS Field Descriptions
BitFieldTypeResetDescription
31-30REBOOTATTEMPTSR0hREBOOTATTEMPTS indicates the number of boot attempts taken before the user application starts.
29-15RESERVEDR0h
14SHDNIOLOCKR0hSHDNIOLOCK indicates when IO is locked due to SHUTDOWN
  • 0h = IO IS NOT Locked due to SHUTDOWN
  • 1h = IO IS Locked due to SHUTDOWN
13SWDCFGDISR0hSWDCFGDIS indicates when user has disabled the use of SWD Port
  • 0h = SWD Port Enabled
  • 1h = SWD Port Disabled
12EXTRSTPINDISR0hEXTRSTPINDIS indicates when user has disabled the use of external reset pin
  • 0h = External Reset Pin Enabled
  • 1h = External Reset Pin Disabled
11-7RESERVEDR0h
6PMUIREFGOODR0hPMUIREFGOOD is set by hardware when the PMU current reference is ready.
  • 0h = IREF is not ready
  • 1h = IREF is ready
5ANACPUMPGOODR0hANACPUMPGOOD is set by hardware when the VBOOST analog mux charge pump is ready.
  • 0h = VBOOST is not ready
  • 1h = VBOOST is ready
4BORLVLR0hBORLVL indicates if a BOR event occured and the BOR threshold was switched to BOR0 by hardware.
  • 0h = No BOR violation occured
  • 1h = A BOR violation occured and the BOR threshold was switched to BOR0
3-2BORCURTHRESHOLDR0hBORCURTHRESHOLD indicates the active brown-out reset supply monitor configuration.
  • 0h = Default minimum threshold; a BOR0- violation triggers a BOR
  • 1h = A BOR1- violation generates a BORLVL interrupt
  • 2h = A BOR2- violation generates a BORLVL interrupt
  • 3h = A BOR3- violation generates a BORLVL interrupt
1FLASHSECR0hFLASHSEC indicates if a flash ECC single bit error was detected and corrected (SEC).
  • 0h = No flash ECC single bit error detected
  • 1h = Flash ECC single bit error was detected and corrected
0FLASHDEDR0hFLASHDED indicates if a flash ECC double bit error was detected (DED).
  • 0h = No flash ECC double bit error detected
  • 1h = Flash ECC double bit error detected

2.9.25 DEDERRADDR (Offset = 120Ch) [Reset = 00000000h]

DEDERRADDR is shown in Figure 2-117 and described in Table 2-129.

Return to the Summary Table.

Memory DED Address

Figure 2-117 DEDERRADDR
313029282726252423222120191817161514131211109876543210
ADDR
R-0h
Table 2-129 DEDERRADDR Field Descriptions
BitFieldTypeResetDescription
31-0ADDRR0hAddress of MEMORY DED Error.

2.9.26 RSTCAUSE (Offset = 1220h) [Reset = 00000000h]

RSTCAUSE is shown in Figure 2-118 and described in Table 2-130.

Return to the Summary Table.

Reset cause

Figure 2-118 RSTCAUSE
313029282726252423222120191817161514131211109876543210
RESERVEDID
R-0hRC-0h
Table 2-130 RSTCAUSE Field Descriptions
BitFieldTypeResetDescription
31-5RESERVEDR0h
4-0IDRC0hID is a read-to-clear field which indicates the lowest level reset cause since the last read.
  • 0h = No reset since last read
  • 1h = POR- violation, SHUTDNSTOREx or PMU trim parity fault
  • 2h = NRST triggered POR (>1s hold)
  • 3h = Software triggered POR
  • 4h = BOR0- violation
  • 5h = SHUTDOWN mode exit
  • 8h = Non-PMU trim parity fault
  • 9h = Fatal clock failure
  • Ch = NRST triggered BOOTRST (<1s hold)
  • Dh = Software triggered BOOTRST
  • Eh = WWDT0 violation
  • 10h = BSL exit
  • 11h = BSL entry
  • 13h = WWDT1 violation
  • 14h = Flash uncorrectable ECC error
  • 15h = CPULOCK violation
  • 1Ah = Debug triggered SYSRST
  • 1Bh = Software triggered SYSRST
  • 1Ch = Debug triggered CPURST
  • 1Dh = Software triggered CPURST

2.9.27 RESETLEVEL (Offset = 1300h) [Reset = 00000000h]

RESETLEVEL is shown in Figure 2-119 and described in Table 2-131.

Return to the Summary Table.

Reset level for application-triggered reset command

Figure 2-119 RESETLEVEL
31302928272625242322212019181716
RESERVED
R-0h
1514131211109876543210
RESERVEDLEVEL
R-0hR/W-0h
Table 2-131 RESETLEVEL Field Descriptions
BitFieldTypeResetDescription
31-3RESERVEDR0h
2-0LEVELR/W0hLEVEL is used to specify the type of reset to be issued when RESETCMD is set to generate a software triggered reset.
  • 0h = Issue a SYSRST (CPU plus peripherals only)
  • 1h = Issue a BOOTRST (CPU, peripherals, and boot configuration routine)
  • 2h = Issue a SYSRST and enter the boot strap loader (BSL)
  • 3h = Issue a power-on reset (POR)
  • 4h = Issue a SYSRST and exit the boot strap loader (BSL)

2.9.28 RESETCMD (Offset = 1304h) [Reset = 00XXXXXXh]

RESETCMD is shown in Figure 2-120 and described in Table 2-132.

Return to the Summary Table.

Execute an application-triggered reset command

Figure 2-120 RESETCMD
31302928272625242322212019181716
KEYRESERVED
W-0hR-0h
1514131211109876543210
RESERVEDGO
R-0hW-0h
Table 2-132 RESETCMD Field Descriptions
BitFieldTypeResetDescription
31-24KEYW0hThe key value of E4h (228) must be written to KEY together with GO to trigger the reset.
  • E4h = Issue reset
23-1RESERVEDR0h
0GOW0hExecute the reset specified in RESETLEVEL.LEVEL. Must be written together with the KEY.
  • 1h = Issue reset

2.9.29 BORTHRESHOLD (Offset = 1308h) [Reset = 00000000h]

BORTHRESHOLD is shown in Figure 2-121 and described in Table 2-133.

Return to the Summary Table.

BOR threshold selection

Figure 2-121 BORTHRESHOLD
31302928272625242322212019181716
RESERVED
R-0h
1514131211109876543210
RESERVEDLEVEL
R-0hR/W-0h
Table 2-133 BORTHRESHOLD Field Descriptions
BitFieldTypeResetDescription
31-2RESERVEDR0h
1-0LEVELR/W0hLEVEL specifies the desired BOR threshold and BOR mode.
  • 0h = Default minimum threshold; a BOR0- violation triggers a BOR
  • 1h = A BOR1- violation generates a BORLVL interrupt
  • 2h = A BOR2- violation generates a BORLVL interrupt
  • 3h = A BOR3- violation generates a BORLVL interrupt

2.9.30 BORCLRCMD (Offset = 130Ch) [Reset = 00XXXXXXh]

BORCLRCMD is shown in Figure 2-122 and described in Table 2-134.

Return to the Summary Table.

Set the BOR threshold

Figure 2-122 BORCLRCMD
31302928272625242322212019181716
KEYRESERVED
W-0hR-0h
1514131211109876543210
RESERVEDGO
R-0hW-0h
Table 2-134 BORCLRCMD Field Descriptions
BitFieldTypeResetDescription
31-24KEYW0hThe key value of C7h (199) must be written to KEY together with GO to trigger the clear and BOR threshold change.
  • C7h = Issue clear
23-1RESERVEDR0h
0GOW0hGO clears any prior BOR violation status indications and attempts to change the active BOR mode to that specified in the LEVEL field of the BORTHRESHOLD register.
  • 1h = Issue clear

2.9.31 SYSOSCFCLCTL (Offset = 1310h) [Reset = 00XXXXXXh]

SYSOSCFCLCTL is shown in Figure 2-123 and described in Table 2-135.

Return to the Summary Table.

SYSOSC frequency correction loop (FCL) ROSC enable

Figure 2-123 SYSOSCFCLCTL
3130292827262524
KEY
W-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVED
R-0h
76543210
RESERVEDSETUSEEXRESSETUSEFCL
R-0hW-0hW-0h
Table 2-135 SYSOSCFCLCTL Field Descriptions
BitFieldTypeResetDescription
31-24KEYW0hThe key value of 2Ah (42) must be written to KEY together with SETUSEFCL to enable the FCL.
  • 2Ah = Issue Command
23-2RESERVEDR0h
1SETUSEEXRESW0hSet SETUSEEXRES to specify that an external resistor will be used for the FCL. An appropriate resistor must be populated on the ROSC pin. This state is locked until the next BOOTRST.
  • 1h = Enable the SYSOSC external Resistor
0SETUSEFCLW0hSet SETUSEFCL to enable the frequency correction loop in SYSOSC. Once enabled, this state is locked until the next BOOTRST.
  • 1h = Enable the SYSOSC FCL

2.9.32 LFXTCTL (Offset = 1314h) [Reset = 00XXXXXXh]

LFXTCTL is shown in Figure 2-124 and described in Table 2-136.

Return to the Summary Table.

LFXT and LFCLK control

Figure 2-124 LFXTCTL
3130292827262524
KEY
W-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVED
R-0h
76543210
RESERVEDSETUSELFXTSTARTLFXT
R-0hW-0hW-0h
Table 2-136 LFXTCTL Field Descriptions
BitFieldTypeResetDescription
31-24KEYW0hThe key value of 91h (145) must be written to KEY together with either STARTLFXT or SETUSELFXT to set the corresponding bit.
  • 91h = Issue command
23-2RESERVEDR0h
1SETUSELFXTW0hSet SETUSELFXT to switch LFCLK to LFXT. Once set, SETUSELFXT remains set until the next BOOTRST.
  • 0h = 0
  • 1h = Use LFXT as the LFCLK source
0STARTLFXTW0hSet STARTLFXT to start the low frequency crystal oscillator (LFXT). Once set, STARTLFXT remains set until the next BOOTRST.
  • 0h = LFXT not started
  • 1h = Start LFXT

2.9.33 EXLFCTL (Offset = 1318h) [Reset = 00XXXXXXh]

EXLFCTL is shown in Figure 2-125 and described in Table 2-137.

Return to the Summary Table.

LFCLK_IN and LFCLK control

Figure 2-125 EXLFCTL
3130292827262524
KEY
W-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVED
R-0h
76543210
RESERVEDSETUSEEXLF
R-0hW-0h
Table 2-137 EXLFCTL Field Descriptions
BitFieldTypeResetDescription
31-24KEYW0hThe key value of 36h (54) must be written to KEY together with SETUSEEXLF to set SETUSEEXLF.
  • 36h = Issue command
23-1RESERVEDR0h
0SETUSEEXLFW0hSet SETUSEEXLF to switch LFCLK to the LFCLK_IN digital clock input. Once set, SETUSEEXLF remains set until the next BOOTRST.
  • 1h = Use LFCLK_IN as the LFCLK source

2.9.34 SHDNIOREL (Offset = 131Ch) [Reset = 00XXXXXXh]

SHDNIOREL is shown in Figure 2-126 and described in Table 2-138.

Return to the Summary Table.

SHUTDOWN IO release control

Figure 2-126 SHDNIOREL
3130292827262524
KEY
W-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVED
R-0h
76543210
RESERVEDRELEASE
R-0hW-0h
Table 2-138 SHDNIOREL Field Descriptions
BitFieldTypeResetDescription
31-24KEYW0hThe key value 91h must be written to KEY together with RELEASE to set RELEASE.
  • 91h = Issue command
23-1RESERVEDR0h
0RELEASEW0hSet RELEASE to release the IO after a SHUTDOWN mode exit.
  • 1h = Release IO

2.9.35 EXRSTPIN (Offset = 1320h) [Reset = 00XXXXXXh]

EXRSTPIN is shown in Figure 2-127 and described in Table 2-139.

Return to the Summary Table.

Disable the reset function of the NRST pin

Figure 2-127 EXRSTPIN
3130292827262524
KEY
W-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVED
R-0h
76543210
RESERVEDDISABLE
R-0hW-0h
Table 2-139 EXRSTPIN Field Descriptions
BitFieldTypeResetDescription
31-24KEYW0hThe key value 1Eh must be written together with DISABLE to disable the reset function.
  • 1Eh = Issue command
23-1RESERVEDR0h
0DISABLEW0hSet DISABLE to disable the reset function of the NRST pin. Once set, this configuration is locked until the next POR.
  • 0h = Reset function of NRST pin is enabled
  • 1h = Reset function of NRST pin is disabled

2.9.36 SYSSTATUSCLR (Offset = 1324h) [Reset = 00XXXXXXh]

SYSSTATUSCLR is shown in Figure 2-128 and described in Table 2-140.

Return to the Summary Table.

Clear sticky bits of SYSSTATUS

Figure 2-128 SYSSTATUSCLR
3130292827262524
KEY
W-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVED
R-0h
76543210
RESERVEDALLECC
R-0hW-0h
Table 2-140 SYSSTATUSCLR Field Descriptions
BitFieldTypeResetDescription
31-24KEYW0hThe key value CEh (206) must be written to KEY together with ALLECC to clear the ECC state.
  • CEh = Issue command
23-1RESERVEDR0h
0ALLECCW0hSet ALLECC to clear all ECC related SYSSTATUS indicators.
  • 1h = Clear ECC error state

2.9.37 SWDCFG (Offset = 1328h) [Reset = 00XXXXXXh]

SWDCFG is shown in Figure 2-129 and described in Table 2-141.

Return to the Summary Table.

Disable the SWD function on the SWD pins

Figure 2-129 SWDCFG
3130292827262524
KEY
W-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVED
R-0h
76543210
RESERVEDDISABLE
R-0hW-0h
Table 2-141 SWDCFG Field Descriptions
BitFieldTypeResetDescription
31-24KEYW0hThe key value 62h (98) must be written to KEY together with DISBALE to disable the SWD functions.
  • 62h = Issue command
23-1RESERVEDR0h
0DISABLEW0hSet DISABLE to disable the SWD function on SWD pins, allowing the SWD pins to be used as GPIO.
  • 1h = Disable SWD function on SWD pins

2.9.38 FCCCMD (Offset = 132Ch) [Reset = 00XXXXXXh]

FCCCMD is shown in Figure 2-130 and described in Table 2-142.

Return to the Summary Table.

Frequency clock counter start capture

Figure 2-130 FCCCMD
31302928272625242322212019181716
KEYRESERVED
W-0hR-0h
1514131211109876543210
RESERVEDGO
R-0hW-0h
Table 2-142 FCCCMD Field Descriptions
BitFieldTypeResetDescription
31-24KEYW0hThe key value 0Eh (14) must be written with GO to start a capture.
  • 0Eh = Issue command
23-1RESERVEDR0h
0GOW0hSet GO to start a capture with the frequency clock counter (FCC).
  • 1h = 1

2.9.39 SHUTDNSTORE0 (Offset = 1400h) [Reset = 00000000h]

SHUTDNSTORE0 is shown in Figure 2-131 and described in Table 2-143.

Return to the Summary Table.

Shutdown storage memory (byte 0)

Figure 2-131 SHUTDNSTORE0
3130292827262524
RESERVED
R-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVED
R-0h
76543210
DATA
R/W-0h
Table 2-143 SHUTDNSTORE0 Field Descriptions
BitFieldTypeResetDescription
31-10RESERVEDR0h
7-0DATAR/W0hShutdown storage byte 0

2.9.40 SHUTDNSTORE1 (Offset = 1404h) [Reset = 00000000h]

SHUTDNSTORE1 is shown in Figure 2-132 and described in Table 2-144.

Return to the Summary Table.

Shutdown storage memory (byte 1)

Figure 2-132 SHUTDNSTORE1
3130292827262524
RESERVED
R-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVED
R-0h
76543210
DATA
R/W-0h
Table 2-144 SHUTDNSTORE1 Field Descriptions
BitFieldTypeResetDescription
31-10RESERVEDR0h
7-0DATAR/W0hShutdown storage byte 1

2.9.41 SHUTDNSTORE2 (Offset = 1408h) [Reset = 00000000h]

SHUTDNSTORE2 is shown in Figure 2-133 and described in Table 2-145.

Return to the Summary Table.

Shutdown storage memory (byte 2)

Figure 2-133 SHUTDNSTORE2
3130292827262524
RESERVED
R-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVED
R-0h
76543210
DATA
R/W-0h
Table 2-145 SHUTDNSTORE2 Field Descriptions
BitFieldTypeResetDescription
31-10RESERVEDR0h
7-0DATAR/W0hShutdown storage byte 2

2.9.42 SHUTDNSTORE3 (Offset = 140Ch) [Reset = 00000000h]

SHUTDNSTORE3 is shown in Figure 2-134 and described in Table 2-146.

Return to the Summary Table.

Shutdown storage memory (byte 3)

Figure 2-134 SHUTDNSTORE3
3130292827262524
RESERVED
R-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVED
R-0h
76543210
DATA
R/W-0h
Table 2-146 SHUTDNSTORE3 Field Descriptions
BitFieldTypeResetDescription
31-10RESERVEDR0h
7-0DATAR/W0hShutdown storage byte 3