SLVSHO1A March   2025  – December 2025 TPS1689

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Device Comparison
  6. 5 Pin Configuration and Functions
  7. 6 Specifications
    1. 6.1  Absolute Maximum Ratings
    2. 6.2  ESD Ratings
    3. 6.3  Recommended Operating Conditions
    4. 6.4  Thermal Information
    5. 6.5  Electrical Characteristics
    6. 6.6  Telemetry
    7. 6.7  PMBus and GPIO DC Characteristics
    8. 6.8  Logic Interface
    9. 6.9  Timing Requirements
    10. 6.10 Switching Characteristics
    11. 6.11 Typical Characteristics
  8. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1  Undervoltage Protection
      2. 7.3.2  Insertion Delay
      3. 7.3.3  Overvoltage Protection
      4. 7.3.4  Inrush Current, Overcurrent, and Short-Circuit Protection
        1. 7.3.4.1 Slew rate (dVdt) and Inrush Current Control
          1. 7.3.4.1.1 Start-Up Timeout
        2. 7.3.4.2 Steady-State Overcurrent Protection (Circuit-Breaker)
        3. 7.3.4.3 Active Current Limiting During Start-Up
        4. 7.3.4.4 Short-Circuit Protection
      5. 7.3.5  Analog Load Current Monitor (IMON)
      6. 7.3.6  Overtemperature Protection
      7. 7.3.7  Analog Junction Temperature Monitor (TEMP)
      8. 7.3.8  FET Health Monitoring
      9. 7.3.9  Single Point Failure Mitigation
        1. 7.3.9.1 IMON Pin Single Point Failure
        2. 7.3.9.2 IREF Pin Single Point Failure
      10. 7.3.10 General Purpose Digital Input/Output Pins
        1. 7.3.10.1 Fault Response and Indication (FLT)
        2. 7.3.10.2 Power Good Indication (PG)
        3. 7.3.10.3 Parallel Device Synchronization (SWEN)
      11. 7.3.11 Stacking Multiple eFuses for Unlimited Scalability
        1. 7.3.11.1 Current Balancing During Start-Up
      12. 7.3.12 Quick Output Discharge(QOD)
      13. 7.3.13 Write Protect Feature(WP#)
      14. 7.3.14 PMBus® Digital Interface
        1. 7.3.14.1  PMBus® Device Addressing
        2. 7.3.14.2  SMBus Protocol
        3. 7.3.14.3  SMBus™ Message Formats
        4. 7.3.14.4  Packet Error Checking
        5. 7.3.14.5  Group Commands
        6. 7.3.14.6  SMBus™ Alert Response Address (ARA)
        7. 7.3.14.7  PMBus® Commands
          1. 7.3.14.7.1 Detailed Descriptions of PMBus® Commands
            1. 7.3.14.7.1.1  OPERATION (01h, Read/Write Byte)
            2. 7.3.14.7.1.2  CLEAR_FAULTS (03h, Send Byte)
            3. 7.3.14.7.1.3  RESTORE_FACTORY_DEFAULTS (12h, Send Byte)
            4. 7.3.14.7.1.4  STORE_USER_ALL (15h, Send Byte)
            5. 7.3.14.7.1.5  RESTORE_USER_ALL (16h, Send Byte)
            6. 7.3.14.7.1.6  BB_ERASE (F5h, Send Byte)
            7. 7.3.14.7.1.7  FETCH_BB_EEPROM (F6h, Send Byte)
            8. 7.3.14.7.1.8  CLEAR_BB_RAM (FCh, Send Byte)
            9. 7.3.14.7.1.9  POWER_CYCLE (D9h, Send Byte)
            10. 7.3.14.7.1.10 MFR_WRITE_PROTECT (F8h, Read/Write Byte)
            11. 7.3.14.7.1.11 CAPABILITY (19h, Read Byte)
            12. 7.3.14.7.1.12 STATUS_BYTE (78h, Read Byte)
            13. 7.3.14.7.1.13 STATUS_WORD (79h, Read Word)
            14. 7.3.14.7.1.14 STATUS_OUT (7Ah, Read Byte)
            15. 7.3.14.7.1.15 STATUS_IOUT (7Bh, Read Byte)
            16. 7.3.14.7.1.16 STATUS_INPUT (7Ch, Read Byte)
            17. 7.3.14.7.1.17 STATUS_TEMP (7Dh, Read Byte)
            18. 7.3.14.7.1.18 STATUS_CML (7Eh, Read Byte)
            19. 7.3.14.7.1.19 STATUS_MFR_SPECIFIC (80h, Read Byte)
            20. 7.3.14.7.1.20 STATUS_MFR_SPECIFIC_2 (F3h, Read Word)
            21. 7.3.14.7.1.21 PMBUS_REVISION (98h, Read Byte)
            22. 7.3.14.7.1.22 MFR_ID (99h, Block Read)
            23. 7.3.14.7.1.23 MFR_MODEL (9Ah, Block Read)
            24. 7.3.14.7.1.24 MFR_REVISION (9Bh, Block Read)
            25. 7.3.14.7.1.25 READ_VIN (88h, Read Word)
            26. 7.3.14.7.1.26 READ_VOUT (8Bh, Read Word)
            27. 7.3.14.7.1.27 READ_IIN (89h, Read Word)
            28. 7.3.14.7.1.28 READ_TEMPERATURE_1 (8Dh, Read Word)
            29. 7.3.14.7.1.29 READ_VAUX (D0h, Read Word)
            30. 7.3.14.7.1.30 READ_PIN (97h, Read Word)
            31. 7.3.14.7.1.31 READ_EIN (86h, Block Read)
            32. 7.3.14.7.1.32 READ_VIN_AVG (DCh, Read Word)
            33. 7.3.14.7.1.33 READ_VIN_MIN (D1h, Read Word)
            34. 7.3.14.7.1.34 READ_VIN_PEAK (D2h, Read Word)
            35. 7.3.14.7.1.35 READ_VOUT_AVG (DDh, Read Word)
            36. 7.3.14.7.1.36 READ_VOUT_MIN (DAh, Read Word)
            37. 7.3.14.7.1.37 READ_IIN_AVG (DEh, Read Word)
            38. 7.3.14.7.1.38 READ_IIN_PEAK (D4h, Read Word)
            39. 7.3.14.7.1.39 READ_TEMP_AVG (D6h, Read Word)
            40. 7.3.14.7.1.40 READ_TEMP_PEAK (D7h, Read Word)
            41. 7.3.14.7.1.41 READ_PIN_AVG (DFh, Read Word)
            42. 7.3.14.7.1.42 READ_PIN_PEAK (D5h, Read Word)
            43. 7.3.14.7.1.43 READ_SAMPLE_BUF (D8h, Block Read)
            44. 7.3.14.7.1.44 READ_BB_RAM (FDh, Block Read)
            45. 7.3.14.7.1.45 READ_BB_EEPROM (F4h, Block Read)
            46. 7.3.14.7.1.46 BB_TIMER (FAh, Read Byte)
            47. 7.3.14.7.1.47 PMBUS_ADDR (FBh, Read/Write Byte)
            48. 7.3.14.7.1.48 VIN_UV_WARN (58h, Read/Write Word)
            49. 7.3.14.7.1.49 VIN_UV_FLT (59h, Read/Write Word)
            50. 7.3.14.7.1.50 VIN_OV_WARN (57h, Read/Write Word)
            51. 7.3.14.7.1.51 VIN_OV_FLT (55h, Read/Write Word)
            52. 7.3.14.7.1.52 VOUT_UV_WARN (43h, Read/Write Word)
            53. 7.3.14.7.1.53 VOUT_PGTH (5Fh, Read/Write Word)
            54. 7.3.14.7.1.54 OT_WARN (51h, Read/Write Word)
            55. 7.3.14.7.1.55 OT_FLT (4Fh, Read/Write Word)
            56. 7.3.14.7.1.56 PIN_OP_WARN (6Bh, Read/Write Word)
            57. 7.3.14.7.1.57 IIN_OC_WARN (5Dh, Read/Write Word)
            58. 7.3.14.7.1.58 ALERT_MASK (DBh, Read/Write Word)
            59. 7.3.14.7.1.59 VIREF (E0h, Read/Write Byte)
            60. 7.3.14.7.1.60 AUX/TEMP/EEDATA/EECLK/GPIOx (E1h, Read/Write Byte)
            61. 7.3.14.7.1.61 SMBA_FLT_CONFIG (E2h, Read/Write Byte)
            62. 7.3.14.7.1.62 FAULT_MASK (E3h, Read/Write Word)
            63. 7.3.14.7.1.63 DEVICE_CONFIG (E4h, Read/Write Word)
            64. 7.3.14.7.1.64 BB_CONFIG (E5h, Read/Write Byte)
            65. 7.3.14.7.1.65 OC_TIMER (E6h, Read/Write Byte)
            66. 7.3.14.7.1.66 RETRY_CONFIG (E7h, Read/Write Byte)
            67. 7.3.14.7.1.67 ADC_CONFIG_1 (E8h, Read/Write Byte)
            68. 7.3.14.7.1.68 ADC_CONFIG_2 (E9h, Read/Write Byte)
            69. 7.3.14.7.1.69 PK_MIN_AVG (EAh, Read/Write Byte)
            70. 7.3.14.7.1.70 PSU_VOLTAGE (ECh, Read/Write Byte)
            71. 7.3.14.7.1.71 CABLE_DROP (EDh, Read/Write Byte)
            72. 7.3.14.7.1.72 IMON OFFSET CALIBRATION (F2h, Read/Write Byte)
            73. 7.3.14.7.1.73 INS_DLY (F9h, Read/Write Byte)
        8. 7.3.14.8  Analog-to-Digital Converter
        9. 7.3.14.9  Digital-to-Analog Converters
        10. 7.3.14.10 DIRECT Format Conversion
        11. 7.3.14.11 Blackbox Fault Recording
    4. 7.4 Device Functional Modes
  9. 8 Application and Implementation
    1. 8.1 Application Information
      1. 8.1.1 Single Device, Standalone Operation
      2. 8.1.2 Single TPS1689x and Multiple TPS1685 Devices, Parallel Connection
      3. 8.1.3 Multiple TPS1689x Devices: Parallel Connection With Individual Telemetry
      4. 8.1.4 Multiple Devices, Independent Operation (Multi-zone)
    2. 8.2 Typical Application: 54V, 2kW Power Path Protection with PMBus® Interface in Datacenter Servers
      1. 8.2.1 Design Requirements
      2. 8.2.2 Detailed Design Procedure
      3. 8.2.3 Application Performance Plots
    3. 8.3 Power Supply Recommendations
      1. 8.3.1 Transient Protection and Other Design Considerations
      2. 8.3.2 Output Short-Circuit Measurements
    4. 8.4 Layout
      1. 8.4.1 Layout Guidelines
      2. 8.4.2 Layout Example
  10. 9 Device and Documentation Support
    1. 9.1 Third-Party Products Disclaimer
    2. 9.2 Documentation Support
      1. 9.2.1 Related Documentation
    3. 9.3 Receiving Notification of Documentation Updates
    4. 9.4 Support Resources
    5. 9.5 Trademarks
    6. 9.6 Electrostatic Discharge Caution
    7. 9.7 Glossary
  11. 10Revision History
  12. 11Mechanical, Packaging, and Orderable Information

7.3.14.1 PMBus® Device Addressing

The TPS1689x uses 7-bit I2C device addressing. Up to 25 different addresses can be generated using different pin-strapping combinations on the ADDR0 and ADDR1 pins as shown in Table 7-5. This allows multiple devices to be connected to the same I2C bus.

Table 7-5 TPS1689x PMBus® Address Decoding
ADDR0 PINADDR1 PINPMBus® DEVICE ADDRESS

Open

Open0x40 (Default). Can be overwritten with a user defined address programmed into PMBUS_ADDR register in the Config NVM space.

Open

GND

0x41

Open

75kΩ to GND

0x42

Open

150kΩ to GND

0x43

Open

267kΩ to GND

0x44

GND

Open

0x45

GND

GND

0x46

GND

75kΩ to GND

0x47

GND

150kΩ to GND

0x48

GND

267kΩ to GND

0x49

75kΩ to GND

Open

0x4A

75kΩ to GNDGND

0x4B

75kΩ to GND75kΩ to GND

0x4C

75kΩ to GND150kΩ to GND

0x4D

75kΩ to GND267kΩ to GND

0x4E

150kΩ to GNDOpen

0x50

150kΩ to GNDGND

0x51

150kΩ to GND75kΩ to GND

0x52

150kΩ to GND150kΩ to GND

0x53

150kΩ to GND267kΩ to GND

0x54

267kΩ to GNDOpen

0x55

267kΩ to GNDGND

0x56

267kΩ to GND75kΩ to GND

0x57

267kΩ to GND150kΩ to GND

0x58

267kΩ to GND267kΩ to GND

0x59

Note:

  1. TI recommends using low tolerance resistors on ADDR0 and ADDR1 to avoid address decoding errors.

  2. TI recommends connecting 10pF capacitors in parallel with resistors on ADDR0 and ADDR1 pins to improve noise immunity for correct address decoding.