首頁 介面 I2C、I3C 與 SPI IC I2C 與 I3C 位準移位器、緩衝器與集線器
首頁
介面
I2C、I3C 與 SPI IC
I2C 與 I3C 位準移位器、緩衝器與集線器

TCA39306-Q1

現行

車用 FM+ I²C 匯流排和 SMBus 電壓轉換器

立即訂購
產品規格表

TCA39306-Q1

現行
產品規格表 立即訂購

產品詳細資料

Features Enable pin Protocols I2C, I3C Frequency (max) (MHz) 12.5 VCCA (min) (V) 0.85 VCCA (max) (V) 5.5 VCCB (min) (V) 1.65 VCCB (max) (V) 5.5 Supply restrictions VCCA <= VCCB Rating Automotive TI functional safety category Functional Safety-Capable Operating temperature range (°C) -40 to 125
Features Enable pin Protocols I2C, I3C Frequency (max) (MHz) 12.5 VCCA (min) (V) 0.85 VCCA (max) (V) 5.5 VCCB (min) (V) 1.65 VCCB (max) (V) 5.5 Supply restrictions VCCA <= VCCB Rating Automotive TI functional safety category Functional Safety-Capable Operating temperature range (°C) -40 to 125
VSSOP (DCU) 8 6.2 mm² 2 x 3.1
  • AEC-Q100 Qualified for automotive applications
  • Functional Safety-Capable
  • 2-Bit bidirectional translator for SDA and SCL lines in mixed-mode I 2C applications
  • Standard-mode, fast-mode, and fast-mode plus I 2C and SMBus compatible
  • I 3C compatible (12.5 MHz supported)
  • Allows voltage-level translation between
    • 0.9-V V REF1 and 1.8-V, 2.5-V, 3.3-V, or 5-V V REF2
    • 1.2-V V REF1 and 1.8-V, 2.5-V, 3.3-V, or 5-V V REF2
    • 1.8-V V REF1 and 2.5-V, 3.3-V, or 5-V V REF2
    • 2.5-V V REF1 and 3.3-V or 5-V V REF2
    • 3.3-V V REF1 and 5-V V REF2
  • Provides bidirectional voltage translation with no direction Pin
  • Low ON-state resistance between input and output ports provides less signal distortion
  • Open-drain I 2C I/O ports (SCL1, SDA1, SCL2, and SDA2)
  • 5-V Tolerant I 2C I/O ports to support mixed-mode signal operation
  • High-impedance SCL1, SDA1, SCL2, and SDA2 pins for EN = Low
  • Lockup-free operation for isolation when EN = Low
  • Flow-through pinout for ease of printed-circuit-board trace routing
  • ESD Protection Exceeds JESD 22
    • 2000-V human-body model (A114-A)
    • 1000-V charged-device model (C101)
  • AEC-Q100 Qualified for automotive applications
  • Functional Safety-Capable
  • 2-Bit bidirectional translator for SDA and SCL lines in mixed-mode I 2C applications
  • Standard-mode, fast-mode, and fast-mode plus I 2C and SMBus compatible
  • I 3C compatible (12.5 MHz supported)
  • Allows voltage-level translation between
    • 0.9-V V REF1 and 1.8-V, 2.5-V, 3.3-V, or 5-V V REF2
    • 1.2-V V REF1 and 1.8-V, 2.5-V, 3.3-V, or 5-V V REF2
    • 1.8-V V REF1 and 2.5-V, 3.3-V, or 5-V V REF2
    • 2.5-V V REF1 and 3.3-V or 5-V V REF2
    • 3.3-V V REF1 and 5-V V REF2
  • Provides bidirectional voltage translation with no direction Pin
  • Low ON-state resistance between input and output ports provides less signal distortion
  • Open-drain I 2C I/O ports (SCL1, SDA1, SCL2, and SDA2)
  • 5-V Tolerant I 2C I/O ports to support mixed-mode signal operation
  • High-impedance SCL1, SDA1, SCL2, and SDA2 pins for EN = Low
  • Lockup-free operation for isolation when EN = Low
  • Flow-through pinout for ease of printed-circuit-board trace routing
  • ESD Protection Exceeds JESD 22
    • 2000-V human-body model (A114-A)
    • 1000-V charged-device model (C101)

The TCA39306-Q1 is a dual bidirectional voltage-level translator compatible with I 2C, SMBus, and I 3C with an enable (EN) input, and is operational from 0.9-V to 3.3-V V REF1 and 1.8-V to 5.5-V V REF2.

The device allows bidirectional voltage translations between 0.85 V and 5 V, without the use of a direction pin. The low ON-state resistance (R ON) of the switch allows connections to be made with minimal propagation delay. When EN is high, the translator switch is ON, and the SCL1 and SDA1 I/O are connected to the SCL2 and SDA2 I/O, respectively, allowing bidirectional data flow between ports. When EN is low, the translator switch is off, and a high-impedance state exists between ports.

In addition to voltage translation, the TCA39306-Q1 can be used to isolate a higher speed bus from a lower speed bus by controlling the EN pin to disconnect the slower bus during fast-mode communication.

The TCA39306-Q1 is a dual bidirectional voltage-level translator compatible with I 2C, SMBus, and I 3C with an enable (EN) input, and is operational from 0.9-V to 3.3-V V REF1 and 1.8-V to 5.5-V V REF2.

The device allows bidirectional voltage translations between 0.85 V and 5 V, without the use of a direction pin. The low ON-state resistance (R ON) of the switch allows connections to be made with minimal propagation delay. When EN is high, the translator switch is ON, and the SCL1 and SDA1 I/O are connected to the SCL2 and SDA2 I/O, respectively, allowing bidirectional data flow between ports. When EN is low, the translator switch is off, and a high-impedance state exists between ports.

In addition to voltage translation, the TCA39306-Q1 can be used to isolate a higher speed bus from a lower speed bus by controlling the EN pin to disconnect the slower bus during fast-mode communication.
filter 尋找其它 I2C 與 I3C 位準移位器、緩衝器與集線器
下載 觀看有字幕稿的影片 影片

技術文件

star =TI 所選的此產品重要文件
找不到結果。請清除您的搜尋條件，然後再試一次。
檢視所有 4
類型 標題 日期
* Data sheet TCA39306-Q1Dual BidirectionalI3C,I2C Bus and SMBus Voltage-Level Translator datasheet (Rev. B) PDF | HTML 2023年 10月 30日
Application note Understanding Transient Drive Strength vs. DC Drive Strength in Level-Shifters (Rev. A) PDF | HTML 2024年 7月 3日
Application brief I3C Voltage Translator and Multiplexer Quick Reference PDF | HTML 2024年 1月 4日
Functional safety information TCA39306-Q1 Functional Safety, FIT Rate, Failure Mode Distribution, and Pin FMA PDF | HTML 2021年 3月 31日

設計與開發

如需其他條款或必要資源，請按一下下方的任何標題以檢視詳細頁面 (如有)。

開發板

TCA39306EVM — TCA39306 評估模組低電壓 I²C 電平移位器

此 EVM 透過可調整上拉電阻器和匯流排電容器提供可配置的負載條件，讓設計人員能在其系統中輕鬆測試此裝置的性能。

使用指南: PDF | HTML
TI.com 無法提供
模擬型號

TCA39306 IBIS Model

SCPM048.ZIP (23 KB) - IBIS Model
下載
設計工具

I2C-DESIGNER — I2C 設計工具

使用 I2C 設計工具快速解決 I2C 設計中在定址、電壓位準和頻率方面的衝突。輸入主裝置和從屬裝置的參數，自動產生 I2C 樹狀結構，或輕鬆建置自訂解決方案。此工具將協助設計人員節省時間並符合 I2C 標準，提供關於偵錯缺失確認、選擇上拉電阻以及滿足 I2C 匯流排最大電容負載的指導。 
在雲端評估
模擬工具

PSPICE-FOR-TI — PSpice® for TI 設計與模擬工具

PSpice® for TI 是有助於評估類比電路功能的設計和模擬環境。這款全功能設計和模擬套件使用 Cadence® 的類比分析引擎。PSpice for TI 包括業界最大的模型庫之一，涵蓋我們的類比和電源產品組合，以及特定類比行為模型，且使用無需支付費用。

PSpice for TI 設計和模擬環境可讓您使用其內建函式庫來模擬複雜的混合訊號設計。在進行佈局和製造之前，建立完整的終端設備設計和解決方案原型，進而縮短上市時間並降低開發成本。 

在 PSpice for TI 設計與模擬工具中，您可以搜尋 TI (...)
要求
模擬工具

TINA-TI — 基於 SPICE 的類比模擬程式

TINA-TI provides all the conventional DC, transient and frequency domain analysis of SPICE and much more. TINA has extensive post-processing capability that allows you to format results the way you want them. Virtual instruments allow you to select input waveforms and probe circuit nodes voltages (...)
使用指南: PDF
View Options
封裝 針腳 CAD 符號、佔位空間與 3D 模型
VSSOP (DCU) 8 Ultra Librarian
適用 TI 的評估品項標準條款與條件。

訂購與品質

內含資訊：
  • RoHS
  • REACH
  • 產品標記
  • 鉛塗層/球物料
  • MSL 等級/回焊峰值
  • MTBF/FIT 估算值
  • 材料內容
  • 認證摘要
  • 進行中持續性的可靠性監測
內含資訊：
  • 晶圓廠位置
  • 組裝地點

建議產品可能具有與此 TI 產品相關的參數、評估模組或參考設計。

支援與培訓

內含 TI 工程師技術支援的 TI E2E™ 論壇

以英文檢視所有論壇主題

內容係由 TI 和社群貢獻者依「現狀」提供，且不構成 TI 規範。檢視使用條款。

若有關於品質、封裝或訂購 TI 產品的問題，請參閱 TI 支援。​​​​​​​​​​​​​​

影片