SWCU194 March   2023 CC1314R10 , CC1354P10 , CC1354R10 , CC2674P10 , CC2674R10

 

  1.   Read This First
    1.     About This Manual
    2.     Devices
    3.     Register, Field, and Bit Calls
    4.     Related Documentation
    5.     Trademarks
  2. 1 Architectural Overview
    1. 1.1 Target Applications
    2. 1.2 Overview
    3. 1.3 Functional Overview
      1. 1.3.1  ArmCortex-M33 with FPU
        1. 1.3.1.1 Processor Core
        2. 1.3.1.2 System Timer (SysTick)
        3. 1.3.1.3 Nested Vector Interrupt Controller (NVIC)
        4. 1.3.1.4 System Control Block (SCB)
      2. 1.3.2  On-Chip Memory
        1. 1.3.2.1 SRAM
        2. 1.3.2.2 Flash Memory
        3. 1.3.2.3 ROM
      3. 1.3.3  Radio
      4. 1.3.4  Security Core
      5. 1.3.5  Runtime Security
      6. 1.3.6  General-Purpose Timers
        1. 1.3.6.1 Watchdog Timer
        2. 1.3.6.2 Always-On Domain
      7. 1.3.7  Direct Memory Access
      8. 1.3.8  System Control and Clock
      9. 1.3.9  Serial Communication Peripherals
        1. 1.3.9.1 UART
        2. 1.3.9.2 I2C
        3. 1.3.9.3 I2S
        4. 1.3.9.4 SPI
      10. 1.3.10 Programmable I/Os
      11. 1.3.11 Sensor Controller
      12. 1.3.12 Random Number Generator
      13. 1.3.13 cJTAG and JTAG
      14. 1.3.14 Power Supply System
        1. 1.3.14.1 Supply System
          1. 1.3.14.1.1 VDDS
          2. 1.3.14.1.2 VDDR
          3. 1.3.14.1.3 Digital Core Supply
          4. 1.3.14.1.4 Other Internal Supplies
        2. 1.3.14.2 DC/DC Converter
  3. 2  Arm Cortex-M33 Processor with FPU
    1. 2.1 Arm Cortex-M33 Processor Introduction
    2. 2.2 Block Diagram
    3. 2.3 Overview
      1. 2.3.1 Integrated Configurable Debug
      2. 2.3.2 Trace Port Interface Unit
      3. 2.3.3 Arm Cortex-M33 System Peripheral Details
        1. 2.3.3.1 Floating Point Unit (FPU)
        2. 2.3.3.2 Memory Protection Unit (MPU)
        3. 2.3.3.3 System Timer (SysTick)
        4. 2.3.3.4 Nested Vectored Interrupt Controller (NVIC)
        5. 2.3.3.5 System Control Block (SCB)
        6. 2.3.3.6 System Control Space (SCS)
        7. 2.3.3.7 Security Attribution Unit (SAU)
    4. 2.4 Programming Model
      1. 2.4.1 Modes of Operation and Execution
        1. 2.4.1.1 Security States
        2. 2.4.1.2 Operating Modes
        3. 2.4.1.3 Operating States
        4. 2.4.1.4 Privileged Access and Unprivileged User Access
      2. 2.4.2 Instruction Set Summary
      3. 2.4.3 Memory Model
        1. 2.4.3.1 Private Peripheral Bus
        2. 2.4.3.2 Unaligned Accesses
      4. 2.4.4 Exclusive Monitor
      5. 2.4.5 Processor Core Registers Summary
      6. 2.4.6 Exceptions
        1. 2.4.6.1 Exception Handling and Prioritization
      7. 2.4.7 Runtime Security
        1. 2.4.7.1 IDAU Watermark Registers
        2. 2.4.7.2 Secure Memory Range for Registers
        3. 2.4.7.3 Bus Topology
        4. 2.4.7.4 Intended Use
    5. 2.5 ArmĀ® CortexĀ®-M33 Registers
      1. 2.5.1  CPU_ITM Registers
      2. 2.5.2  CPU_DWT Registers
      3. 2.5.3  CPU_SYSTICK Registers
      4. 2.5.4  CPU_NVIC Registers
      5. 2.5.5  CPU_SCS Registers
      6. 2.5.6  CPU_MPU Registers
      7. 2.5.7  CPU_SAU Registers
      8. 2.5.8  CPU_DCB Registers
      9. 2.5.9  CPU_SIG Registers
      10. 2.5.10 CPU_FPU Registers
      11. 2.5.11 CPU_TPIU Registers
  4. 3 Memory Map
    1. 3.1 Introduction
    2. 3.2 Memory Map (Secure and Non-secure)
      1. 3.2.1 Bus Security
    3. 3.3 Memory Map
  5. 4  Arm Cortex-M33 Peripherals
    1. 4.1 Arm Cortex-M33 Peripherals Introduction
  6. 5 Interrupts and Events
    1. 5.1 Exception Model
      1. 5.1.1 Exception States
      2. 5.1.2 Exception Types
      3. 5.1.3 Exception Handlers
      4. 5.1.4 Vector Table
      5. 5.1.5 Exception Priorities
      6. 5.1.6 Interrupt Priority Grouping
      7. 5.1.7 Exception Entry and Return
        1. 5.1.7.1 Exception Entry
        2. 5.1.7.2 Exception Return
    2. 5.2 Fault Handling
      1. 5.2.1 Fault Types
      2. 5.2.2 Fault Escalation and Hard Faults
      3. 5.2.3 Fault Status Registers and Fault Address Registers
      4. 5.2.4 Lockup
    3. 5.3 Security State Switches
    4. 5.4 Event Fabric
      1. 5.4.1 Introduction
      2. 5.4.2 Event Fabric Overview
        1. 5.4.2.1 Registers
    5. 5.5 AON Event Fabric
      1. 5.5.1 Common Input Event List
      2. 5.5.2 Event Subscribers
        1. 5.5.2.1 AON Power Management Controller (AON_PMCTL)
        2. 5.5.2.2 Real-Time Clock
        3. 5.5.2.3 MCU Event Fabric
    6. 5.6 MCU Event Fabric
      1. 5.6.1 Common Input Event List
      2. 5.6.2 Event Subscribers
        1. 5.6.2.1 System CPU
        2. 5.6.2.2 NMI
        3. 5.6.2.3 Freeze
    7. 5.7 AON Events
    8. 5.8 Interrupts and Events Registers
      1. 5.8.1 AON_EVENT Registers
      2. 5.8.2 EVENT Registers
  7. 6 JTAG Interface
    1. 6.1 Overview
    2. 6.2 cJTAG
    3. 6.3 ICEPick
      1. 6.3.1 Secondary TAPs
        1. 6.3.1.1 Slave DAP (CPU DAP)
      2. 6.3.2 ICEPick Registers
        1. 6.3.2.1 IR Instructions
        2. 6.3.2.2 Data Shift Register
        3. 6.3.2.3 Instruction Register
        4. 6.3.2.4 Bypass Register
        5. 6.3.2.5 Device Identification Register
        6. 6.3.2.6 User Code Register
        7. 6.3.2.7 ICEPick Identification Register
        8. 6.3.2.8 Connect Register
      3. 6.3.3 Router Scan Chain
      4. 6.3.4 TAP Routing Registers
        1. 6.3.4.1 ICEPick Control Block
          1. 6.3.4.1.1 All0s Register
          2. 6.3.4.1.2 ICEPick Control Register
          3. 6.3.4.1.3 Linking Mode Register
        2. 6.3.4.2 Test TAP Linking Block
          1. 6.3.4.2.1 Secondary Test TAP Register
        3. 6.3.4.3 Debug TAP Linking Block
          1. 6.3.4.3.1 Secondary Debug TAP Register
    4. 6.4 ICEMelter
    5. 6.5 Serial Wire Viewer (SWV)
    6. 6.6 Halt In Boot (HIB)
    7. 6.7 Debug and Shutdown
    8. 6.8 Boundary Scan
  8. 7 Power, Reset, and Clock Management (PRCM)
    1. 7.1 Introduction
    2. 7.2 System CPU Mode
    3. 7.3 Supply System
      1. 7.3.1 Internal DC/DC Converter and Global LDO
      2. 7.3.2 External Regulator Mode
    4. 7.4 Digital Power Partitioning
      1. 7.4.1 MCU_VD
        1. 7.4.1.1 MCU_VD Power Domains
      2. 7.4.2 AON_VD
        1. 7.4.2.1 AON_VD Power Domains
    5. 7.5 Clock Management
      1. 7.5.1 System Clocks
        1. 7.5.1.1 Controlling the Oscillators
      2. 7.5.2 Clocks in MCU_VD
        1. 7.5.2.1 Clock Gating
        2. 7.5.2.2 Scaler to GPTs
        3. 7.5.2.3 Scaler to WDT
      3. 7.5.3 Clocks in AON_VD
    6. 7.6 Power Modes
      1. 7.6.1 Start-Up State
      2. 7.6.2 Active Mode
      3. 7.6.3 Idle Mode
      4. 7.6.4 Standby Mode
      5. 7.6.5 Shutdown Mode
    7. 7.7 Reset
      1. 7.7.1 System Resets
        1. 7.7.1.1 Clock Loss Detection
        2. 7.7.1.2 Software-Initiated System Reset
        3. 7.7.1.3 Warm Reset Converted to System Reset
      2. 7.7.2 Reset of the MCU_VD Power Domains and Modules
      3. 7.7.3 Reset of AON_VD
      4. 7.7.4 Always On Watchdog Timer (AON_WDT)
    8. 7.8 PRCM Registers
      1. 7.8.1 PRCM Registers
      2. 7.8.2 AON_PMCTL Registers
      3. 7.8.3 DDI_0_OSC Registers
  9. 8 Versatile Instruction Memory System (VIMS)
    1. 8.1 Introduction
    2. 8.2 VIMS Configurations
      1. 8.2.1 VIMS Modes
        1. 8.2.1.1 GPRAM Mode
        2. 8.2.1.2 Off Mode
        3. 8.2.1.3 Cache Mode
      2. 8.2.2 VIMS FLASH Line Buffers
      3. 8.2.3 VIMS Arbitration
      4. 8.2.4 VIMS Cache TAG Prefetch
    3. 8.3 VIMS Software Remarks
      1. 8.3.1 FLASH Program or Update
      2. 8.3.2 VIMS Retention
        1. 8.3.2.1 Mode 1
        2. 8.3.2.2 Mode 2
        3. 8.3.2.3 Mode 3
    4. 8.4 FLASH
      1. 8.4.1 Flash Memory Protection
      2. 8.4.2 Flash Memory Programming
    5. 8.5 ROM Functions
    6. 8.6 VIMS Registers
      1. 8.6.1 FLASH Registers
      2. 8.6.2 VIMS Registers
      3. 8.6.3 NVMNW Registers
  10. 9 SRAM
    1. 9.1 Introduction
    2. 9.2 Main Features
    3. 9.3 Data Retention
    4. 9.4 Parity and SRAM Error Support
      1. 9.4.1 SRAM Extension Mode
    5. 9.5 SRAM Auto-Initialization
    6. 9.6 Parity Debug Behavior
    7. 9.7 SRAM Registers
      1. 9.7.1 SRAM_MMR Registers
      2. 9.7.2 SRAM Registers
  11. 10Bootloader
    1. 10.1 Bootloader Functionality
      1. 10.1.1 Bootloader Disabling
      2. 10.1.2 Bootloader Backdoor
    2. 10.2 Bootloader Interfaces
      1. 10.2.1 Packet Handling
        1. 10.2.1.1 Packet Acknowledge and Not-Acknowledge Bytes
      2. 10.2.2 Transport Layer
        1. 10.2.2.1 UART Transport
          1. 10.2.2.1.1 UART Baud Rate Automatic Detection
        2. 10.2.2.2 SPI Transport
      3. 10.2.3 Serial Bus Commands
        1. 10.2.3.1  COMMAND_PING
        2. 10.2.3.2  COMMAND_DOWNLOAD
        3. 10.2.3.3  COMMAND_GET_STATUS
        4. 10.2.3.4  COMMAND_SEND_DATA
        5. 10.2.3.5  COMMAND_RESET
        6. 10.2.3.6  COMMAND_SECTOR_ERASE
        7. 10.2.3.7  COMMAND_CRC32
        8. 10.2.3.8  COMMAND_GET_CHIP_ID
        9. 10.2.3.9  COMMAND_MEMORY_READ
        10. 10.2.3.10 COMMAND_MEMORY_WRITE
        11. 10.2.3.11 COMMAND_BANK_ERASE
        12. 10.2.3.12 COMMAND_SET_CCFG
        13. 10.2.3.13 COMMAND_DOWNLOAD_CRC
  12. 11Device Configuration
    1. 11.1 Customer Configuration (CCFG)
      1. 11.1.1 CCFG Recommendations for Final Production
    2. 11.2 CCFG Registers
    3. 11.3 Factory Configuration (FCFG)
    4. 11.4 FCFG1 Registers
  13. 12AES and Hash Cryptoprocessor
    1. 12.1 Introduction
    2. 12.2 Functional Description
      1. 12.2.1 Debug Capabilities
      2. 12.2.2 Exception Handling
      3. 12.2.3 Power Management and Sleep Modes
      4. 12.2.4 Interrupts
      5. 12.2.5 Module Memory Map
      6. 12.2.6 Master Control and Select Module
        1. 12.2.6.1 Algorithm Select Register
          1. 12.2.6.1.1 Algorithm Select
        2. 12.2.6.2 Master PROT Enable
          1. 12.2.6.2.1 Master PROT-Privileged Access-Enable
        3. 12.2.6.3 Software Reset
      7. 12.2.7 AES Engine
        1. 12.2.7.1 Second and Third Key Registers (Internal, but Clearable)
        2. 12.2.7.2 AES Initialization Vector (IV) Registers
        3. 12.2.7.3 AES I/O Buffer Control, Mode, and Length Registers
        4. 12.2.7.4 AES Data Input and Output Registers
        5. 12.2.7.5 TAG Registers
      8. 12.2.8 Key Area Registers
        1. 12.2.8.1 Key Store Write Area Register
        2. 12.2.8.2 Key Store Written Area Register
        3. 12.2.8.3 Key Store Size Register
        4. 12.2.8.4 Key Store Read Area Register
      9. 12.2.9 Hash Engine
        1. 12.2.9.1 Hash I/O Buffer Control and Status Register, Mode, and Length Registers
        2. 12.2.9.2 Hash Data Input and Digest Registers
    3. 12.3 DMA Controller
      1. 12.3.1 Internal Operation
      2. 12.3.2 Supported DMA Operations
    4. 12.4 AES and Hash Cryptoprocessor Performance
      1. 12.4.1 Introduction
      2. 12.4.2 Performance for DMA-Based Operations
    5. 12.5 Programming Guidelines
      1. 12.5.1 One-Time Initialization After a Reset
      2. 12.5.2 DMAC and Master Control
        1. 12.5.2.1 Regular Use
        2. 12.5.2.2 Interrupting DMA Transfers
        3. 12.5.2.3 Interrupts, Hardware, and Software Synchronization
      3. 12.5.3 Hashing
        1. 12.5.3.1 Data Format and Byte Order
        2. 12.5.3.2 Basic Hash with Data From DMA
          1. 12.5.3.2.1 New Hash Session with Digest Read Through Slave
          2. 12.5.3.2.2 New Hash Session with Digest to External Memory
          3. 12.5.3.2.3 Resumed Hash Session
        3. 12.5.3.3 HMAC
          1. 12.5.3.3.1 Secure HMAC
        4. 12.5.3.4 Alternative Basic Hash Where Data Originates from Slave Interface
          1. 12.5.3.4.1 New Hash Session
          2. 12.5.3.4.2 Resumed Hash Session
      4. 12.5.4 Encryption and Decryption
        1. 12.5.4.1 Data Format and Byte Order
        2. 12.5.4.2 Key Store
          1. 12.5.4.2.1 Load Keys from External Memory
        3. 12.5.4.3 Basic AES Modes
          1. 12.5.4.3.1 AES-ECB
          2. 12.5.4.3.2 AES-CBC
          3. 12.5.4.3.3 AES-CTR
          4. 12.5.4.3.4 Programming Sequence with DMA Data
        4. 12.5.4.4 CBC-MAC
          1. 12.5.4.4.1 Programming Sequence for Regular CBC-MAC
          2. 12.5.4.4.2 Programming Sequence for Regular CBC-MAC with Continuation
          3. 12.5.4.4.3 Programming Sequence for CMAC CBC-MAC
          4. 12.5.4.4.4 Programming Sequence for CMAC CBC-MAC with Continuation
        5. 12.5.4.5 AES-CCM
          1. 12.5.4.5.1 Continued CCM Processing
          2. 12.5.4.5.2 Programming Sequence for AES-CCM
          3. 12.5.4.5.3 Programming Sequence for Continued AES-CCM in the AAD Phase
          4. 12.5.4.5.4 Programming Sequence for Continued AES-CCM in the Payload Phase
        6. 12.5.4.6 AES-GCM
          1. 12.5.4.6.1 Continued AES-GCM Processing
          2. 12.5.4.6.2 Programming Sequence for AES-GCM
          3. 12.5.4.6.3 Programming Sequence for Continued AES-GCM in the AAD Phase
          4. 12.5.4.6.4 Programming Sequence for Continued AES-GCM in the Payload Phase
      5. 12.5.5 Exceptions Handling
        1. 12.5.5.1 Soft Reset
        2. 12.5.5.2 External Port Errors
        3. 12.5.5.3 Key Store Errors
    6. 12.6 Conventions and Compliances
      1. 12.6.1 Conventions Used in This Manual
        1. 12.6.1.1 Terminology
        2. 12.6.1.2 Formulas and Nomenclature
      2. 12.6.2 Compliance
    7. 12.7 CRYPTO Registers
  14. 13PKA Engine
    1. 13.1 Introduction
    2. 13.2 Functional Description
      1. 13.2.1 Module Architecture
      2. 13.2.2 PKA RAM
      3. 13.2.3 PKCP Operations
      4. 13.2.4 Sequencer Operations
        1. 13.2.4.1 Modular Exponentiation Operations
        2. 13.2.4.2 Modular Inversion Operation
        3. 13.2.4.3 ECC Operations
      5. 13.2.5 Operation Sequence
    3. 13.3 PKA Engine Performance
      1. 13.3.1 Basic Operations Performance
      2. 13.3.2 ExpMod Performance
      3. 13.3.3 Modular Inversion Performance
      4. 13.3.4 ECC Operation Performance
    4. 13.4 PKA Registers
  15. 14True Random Number Generator (TRNG)
    1. 14.1 Introduction
    2. 14.2 Block Diagram
    3. 14.3 TRNG Software Reset
    4. 14.4 Interrupt Requests
    5. 14.5 TRNG Operation Description
      1. 14.5.1 TRNG Shutdown
      2. 14.5.2 TRNG Alarms
      3. 14.5.3 TRNG Entropy
    6. 14.6 TRNG Low-Level Programming Guide
      1. 14.6.1 Initialization
        1. 14.6.1.1 Interfacing Modules
        2. 14.6.1.2 TRNG Main Sequence
        3. 14.6.1.3 TRNG Operating Modes
          1. 14.6.1.3.1 Polling Mode
          2. 14.6.1.3.2 Interrupt Mode
    7. 14.7 TRNG Registers
  16. 15I/O Controller (IOC)
    1. 15.1  Introduction
    2. 15.2  IOC Overview
    3. 15.3  I/O Mapping and Configuration
      1. 15.3.1 Basic I/O Mapping
      2. 15.3.2 Mapping AUXIOs to DIO Pins
      3. 15.3.3 Control External LNA/PA (Range Extender) with I/Os
      4. 15.3.4 Map the 32 kHz System Clock (SCLK_LF Clock) to DIO
    4. 15.4  Edge Detection on DIO Pins
      1. 15.4.1 Configure DIO as GPIO Input to Generate Interrupt on Edge Detect
    5. 15.5  Unused I/O Pins
    6. 15.6  GPIO
    7. 15.7  I/O Pin Capability
    8. 15.8  Peripheral PORT_IDs
    9. 15.9  I/O Pins
      1. 15.9.1 Input/Output Modes
        1. 15.9.1.1 Physical Pin
        2. 15.9.1.2 Pin Configuration
    10. 15.10 IOC Registers
      1. 15.10.1 AON_IOC Registers
      2. 15.10.2 GPIO Registers
      3. 15.10.3 IOC Registers
  17. 16Micro Direct Memory Access (ĀµDMA)
    1. 16.1 Introduction
    2. 16.2 Block Diagram
    3. 16.3 Functional Description
      1. 16.3.1  Channel Assignments
      2. 16.3.2  Priority
      3. 16.3.3  Arbitration Size
      4. 16.3.4  Request Types
        1. 16.3.4.1 Single Request
        2. 16.3.4.2 Burst Request
      5. 16.3.5  Channel Configuration
      6. 16.3.6  Transfer Modes
        1. 16.3.6.1 Stop Mode
        2. 16.3.6.2 Basic Mode
        3. 16.3.6.3 Auto Mode
        4. 16.3.6.4 Ping-Pong Mode
        5. 16.3.6.5 Memory Scatter-Gather Mode
        6. 16.3.6.6 Peripheral Scatter-Gather Mode
      7. 16.3.7  Transfer Size and Increments
      8. 16.3.8  Peripheral Interface
      9. 16.3.9  Software Request
      10. 16.3.10 Interrupts and Errors
    4. 16.4 Initialization and Configuration
      1. 16.4.1 Module Initialization
      2. 16.4.2 Configuring a Memory-to-Memory Transfer
        1. 16.4.2.1 Configure the Channel Attributes
        2. 16.4.2.2 Configure the Channel Control Structure
        3. 16.4.2.3 Start the Transfer
    5. 16.5 UDMA Registers
  18. 17Timers
    1. 17.1 Introduction
    2. 17.2 Block Diagram
    3. 17.3 Functional Description
      1. 17.3.1 GPTM Reset Conditions
      2. 17.3.2 Timer Modes
        1. 17.3.2.1 One-Shot or Periodic Timer Mode
        2. 17.3.2.2 Input Edge-Count Mode
        3. 17.3.2.3 Input Edge-Time Mode
        4. 17.3.2.4 PWM Mode
        5. 17.3.2.5 Wait-for-Trigger Mode
      3. 17.3.3 Synchronizing GPT Blocks
      4. 17.3.4 Accessing Concatenated 16- and 32-Bit GPTM Register Values
    4. 17.4 Initialization and Configuration
      1. 17.4.1 One-Shot and Periodic Timer Modes
      2. 17.4.2 Input Edge-Count Mode
      3. 17.4.3 Input Edge-Timing Mode
      4. 17.4.4 PWM Mode
      5. 17.4.5 Producing DMA Trigger Events
    5. 17.5 GPT Registers
  19. 18Real-Time Clock (RTC)
    1. 18.1 Introduction
    2. 18.2 Functional Specifications
      1. 18.2.1 Functional Overview
      2. 18.2.2 Free-Running Counter
      3. 18.2.3 Channels
        1. 18.2.3.1 Capture and Compare
      4. 18.2.4 Events
    3. 18.3 RTC Register Information
      1. 18.3.1 Register Access
      2. 18.3.2 Entering Sleep and Wakeup From Sleep
      3. 18.3.3 AON_RTC:SYNC Register
    4. 18.4 RTC Registers
      1. 18.4.1 AON_RTC Registers
  20. 19Watchdog Timer (WDT)
    1. 19.1 Introduction
    2. 19.2 Functional Description
    3. 19.3 Initialization and Configuration
    4. 19.4 WDT Registers
  21. 20AUX Domain Sensor Controller and Peripherals
    1. 20.1 Introduction
      1. 20.1.1 AUX Block Diagram
    2. 20.2 Power and Clock Management
      1. 20.2.1 Operational Modes
        1. 20.2.1.1 Dual-Rate AUX Clock
      2. 20.2.2 Use Scenarios
        1. 20.2.2.1 MCU
        2. 20.2.2.2 Sensor Controller
      3. 20.2.3 SCE Clock Emulation
      4. 20.2.4 AUX RAM Retention
    3. 20.3 Sensor Controller
      1. 20.3.1 Sensor Controller Studio
        1. 20.3.1.1 Programming Model
        2. 20.3.1.2 Task Development
        3. 20.3.1.3 Task Testing, Task Debugging and Run-Time Logging
        4. 20.3.1.4 Documentation
      2. 20.3.2 Sensor Controller Engine (SCE)
        1. 20.3.2.1  Registers
          1.        Pipeline Hazards
        2. 20.3.2.2  Memory Architecture
          1.        Memory Access to Instructions and Data
          2.        I/O Access to Module Registers
        3. 20.3.2.3  Program Flow
          1.        Zero-Overhead Loop
        4. 20.3.2.4  Instruction Set
          1. 20.3.2.4.1 Instruction Timing
          2. 20.3.2.4.2 Instruction Prefix
          3. 20.3.2.4.3 Instructions
        5. 20.3.2.5  SCE Event Interface
        6. 20.3.2.6  Math Accelerator (MAC)
        7. 20.3.2.7  Programmable Microsecond Delay
        8. 20.3.2.8  Wake-Up Event Handling
        9. 20.3.2.9  Access to AON Domain Registers
        10. 20.3.2.10 VDDR Recharge
    4. 20.4 Digital Peripheral Modules
      1. 20.4.1 Overview
        1. 20.4.1.1 DDI Control-Configuration
      2. 20.4.2 Analog I/O Digital I/O (AIODIO)
        1. 20.4.2.1 Introduction
        2. 20.4.2.2 Functional Description
          1. 20.4.2.2.1 Mapping to DIO Pins
          2. 20.4.2.2.2 Configuration
          3. 20.4.2.2.3 GPIO Mode
          4. 20.4.2.2.4 Input Buffer
          5. 20.4.2.2.5 Data Output Source
      3. 20.4.3 Semaphore (SMPH)
        1. 20.4.3.1 Introduction
        2. 20.4.3.2 Functional Description
        3. 20.4.3.3 Semaphore Allocation in TI Software
      4. 20.4.4 SPI Master (SPIM)
        1. 20.4.4.1 Introduction
        2. 20.4.4.2 Functional Description
          1. 20.4.4.2.1 TX and RX Operations
          2. 20.4.4.2.2 Configuration
          3. 20.4.4.2.3 Timing Diagrams
      5. 20.4.5 Time-to-Digital Converter (TDC)
        1. 20.4.5.1 Introduction
        2. 20.4.5.2 Functional Description
          1. 20.4.5.2.1 Command
          2. 20.4.5.2.2 Conversion Time Configuration
          3. 20.4.5.2.3 Status and Result
          4. 20.4.5.2.4 Clock Source Selection
            1. 20.4.5.2.4.1 Counter Clock
            2. 20.4.5.2.4.2 Reference Clock
          5. 20.4.5.2.5 Start and Stop Events
          6. 20.4.5.2.6 Prescaler
        3. 20.4.5.3 Supported Measurement Types
          1. 20.4.5.3.1 Measure Pulse Width
          2. 20.4.5.3.2 Measure Frequency
          3. 20.4.5.3.3 Measure Time Between Edges of Different Events Sources
            1. 20.4.5.3.3.1 Asynchronous Counter Start ā€“ Ignore 0 Stop Events
            2. 20.4.5.3.3.2 Synchronous Counter Start ā€“ Ignore 0 Stop Events
            3. 20.4.5.3.3.3 Asynchronous Counter Start ā€“ Ignore Stop Events
            4. 20.4.5.3.3.4 Synchronous Counter Start ā€“ Ignore Stop Events
          4. 20.4.5.3.4 Pulse Counting
      6. 20.4.6 Timer01
        1. 20.4.6.1 Introduction
        2. 20.4.6.2 Functional Description
      7. 20.4.7 Timer2
        1. 20.4.7.1 Introduction
        2. 20.4.7.2 Functional Description
          1. 20.4.7.2.1 Clock Source
          2. 20.4.7.2.2 Clock Prescaler
          3. 20.4.7.2.3 Counter
          4. 20.4.7.2.4 Event Outputs
          5. 20.4.7.2.5 Channel Actions
            1. 20.4.7.2.5.1 Period and Pulse Width Measurement
            2. 20.4.7.2.5.2 Clear on Zero, Toggle on Compare Repeatedly
            3. 20.4.7.2.5.3 Set on Zero, Toggle on Compare Repeatedly
          6. 20.4.7.2.6 Asynchronous Bus Bridge
    5. 20.5 Analog Peripheral Modules
      1. 20.5.1 Overview
        1. 20.5.1.1 ADI Control-Configuration
        2. 20.5.1.2 Block Diagram
      2. 20.5.2 Analog-to-Digital Converter (ADC)
        1. 20.5.2.1 Introduction
        2. 20.5.2.2 Functional Description
          1. 20.5.2.2.1 Input Selection and Scaling
          2. 20.5.2.2.2 Reference Selection
          3. 20.5.2.2.3 ADC Sample Mode
          4. 20.5.2.2.4 ADC Clock Source
          5. 20.5.2.2.5 ADC Trigger
          6. 20.5.2.2.6 Sample FIFO
          7. 20.5.2.2.7 ĀµDMA Interface
          8. 20.5.2.2.8 Resource Ownership and Usage
      3. 20.5.3 Comparator A (COMPA)
        1. 20.5.3.1 Introduction
        2. 20.5.3.2 Functional Description
          1. 20.5.3.2.1 Input Selection
          2. 20.5.3.2.2 Reference Selection
          3. 20.5.3.2.3 LPM Bias and COMPA Enable
          4. 20.5.3.2.4 Resource Ownership and Usage
      4. 20.5.4 Comparator B (COMPB)
        1. 20.5.4.1 Introduction
        2. 20.5.4.2 Functional Description
          1. 20.5.4.2.1 Input Selection
          2. 20.5.4.2.2 Reference Selection
          3. 20.5.4.2.3 Resource Ownership and Usage
            1. 20.5.4.2.3.1 Sensor Controller Wakeup
            2. 20.5.4.2.3.2 System CPU Wakeup
      5. 20.5.5 Reference Digital-to-Analog Converter (DAC)
        1. 20.5.5.1 Introduction
        2. 20.5.5.2 Functional Description
          1. 20.5.5.2.1 Reference Selection
          2. 20.5.5.2.2 Output Voltage Control and Range
          3. 20.5.5.2.3 Sample Clock
            1. 20.5.5.2.3.1 Automatic Phase Control
            2. 20.5.5.2.3.2 Manual Phase Control
            3. 20.5.5.2.3.3 Operational Mode Dependency
          4. 20.5.5.2.4 Output Selection
            1. 20.5.5.2.4.1 Buffer
            2. 20.5.5.2.4.2 External Load
            3. 20.5.5.2.4.3 COMPA_REF
            4. 20.5.5.2.4.4 COMPB_REF
          5. 20.5.5.2.5 LPM Bias
          6. 20.5.5.2.6 Resource Ownership and Usage
      6. 20.5.6 Current Source (ISRC)
        1. 20.5.6.1 Introduction
        2. 20.5.6.2 Functional Description
          1. 20.5.6.2.1 Programmable Current
          2. 20.5.6.2.2 Voltage Reference
          3. 20.5.6.2.3 ISRC Enable
          4. 20.5.6.2.4 Temperature Dependency
          5. 20.5.6.2.5 Resource Ownership and Usage
    6. 20.6 Event Routing and Usage
      1. 20.6.1 AUX Event Bus
        1. 20.6.1.1 Event Signals
        2. 20.6.1.2 Event Subscribers
          1. 20.6.1.2.1 Event Detection
            1. 20.6.1.2.1.1 Detection of Asynchronous Events
            2. 20.6.1.2.1.2 Detection of Synchronous Events
      2. 20.6.2 Event Observation on External Pin
      3. 20.6.3 Events From MCU Domain
      4. 20.6.4 Events to MCU Domain
      5. 20.6.5 Events From AON Domain
      6. 20.6.6 Events to AON Domain
      7. 20.6.7 ĀµDMA Interface
    7. 20.7 Sensor Controller Alias Register Space
    8. 20.8 AUX Domain Sensor Controller and Peripherals Registers
      1. 20.8.1  ADI_4_AUX Registers
      2. 20.8.2  AUX_AIODIO Registers
      3. 20.8.3  AUX_EVCTL Registers
      4. 20.8.4  AUX_SMPH Registers
      5. 20.8.5  AUX_TDC Registers
      6. 20.8.6  AUX_TIMER01 Registers
      7. 20.8.7  AUX_TIMER2 Registers
      8. 20.8.8  AUX_ANAIF Registers
      9. 20.8.9  AUX_SYSIF Registers
      10. 20.8.10 AUX_SPIM Registers
      11. 20.8.11 AUX_MAC Registers
      12. 20.8.12 AUX_SCE Registers
  22. 21Battery Monitor and Temperature Sensor (BATMON)
    1. 21.1 Introduction
    2. 21.2 Functional Description
    3. 21.3 AON_BATMON Registers
  23. 22Universal Asynchronous Receiver/Transmitter (UART)
    1. 22.1 Introduction
    2. 22.2 Block Diagram
    3. 22.3 Signal Description
    4. 22.4 Functional Description
      1. 22.4.1 Transmit and Receive Logic
      2. 22.4.2 Baud Rate Generation
      3. 22.4.3 Data Transmission
      4. 22.4.4 Modem Handshake Support
        1. 22.4.4.1 Signaling
        2. 22.4.4.2 Flow Control
          1. 22.4.4.2.1 Hardware Flow Control (RTS and CTS)
          2. 22.4.4.2.2 Software Flow Control (Modem Status Interrupts)
      5. 22.4.5 FIFO Operation
      6. 22.4.6 Interrupts
      7. 22.4.7 Loopback Operation
    5. 22.5 Interface to ĀµDMA
    6. 22.6 Initialization and Configuration
    7. 22.7 UART Registers
  24. 23Serial Peripheral Interface (SPI)
    1. 23.1 Introduction
    2. 23.2 Block Diagram
    3. 23.3 Signal Description
    4. 23.4 Functional Description
      1. 23.4.1 Bit Rate Generation
      2. 23.4.2 FIFO Operation
        1. 23.4.2.1 Transmit FIFO
          1. 23.4.2.1.1 Repeated Transmit Operation
        2. 23.4.2.2 Receive FIFO
        3. 23.4.2.3 FIFO Flush
      3. 23.4.3 Interrupts
      4. 23.4.4 Data Format
      5. 23.4.5 Delayed Data Sampling
      6. 23.4.6 Frame Formats
        1. 23.4.6.1 Texas Instruments Synchronous Serial Frame Format
        2. 23.4.6.2 Motorola SPI Frame Format
          1. 23.4.6.2.1 SPO Clock Polarity Bit
          2. 23.4.6.2.2 SPH Phase Control Bit
        3. 23.4.6.3 Motorola SPI Frame Format with SPO = 0 and SPH = 0
        4. 23.4.6.4 Motorola SPI Frame Format with SPO = 0 and SPH = 1
        5. 23.4.6.5 Motorola SPI Frame Format with SPO = 1 and SPH = 0
        6. 23.4.6.6 Motorola SPI Frame Format with SPO = 1 and SPH = 1
        7. 23.4.6.7 MICROWIRE Frame Format
    5. 23.5 Ī¼DMA Operation
    6. 23.6 Initialization and Configuration
    7. 23.7 SPI Registers
  25. 24Inter-Integrated Circuit (I2C)
    1. 24.1 Introduction
    2. 24.2 Block Diagram
    3. 24.3 Functional Description
      1. 24.3.1 I2C Bus Functional Overview
        1. 24.3.1.1 Start and Stop Conditions
        2. 24.3.1.2 Data Format with 7-Bit Address
        3. 24.3.1.3 Data Validity
        4. 24.3.1.4 Acknowledge
        5. 24.3.1.5 Arbitration
      2. 24.3.2 Available Speed Modes
        1. 24.3.2.1 Standard and Fast Modes
      3. 24.3.3 Interrupts
        1. 24.3.3.1 I2C Master Interrupts
        2. 24.3.3.2 I2C Slave Interrupts
      4. 24.3.4 Loopback Operation
      5. 24.3.5 Command Sequence Flow Charts
        1. 24.3.5.1 I2C Master Command Sequences
        2. 24.3.5.2 I2C Slave Command Sequences
    4. 24.4 Initialization and Configuration
    5. 24.5 I2C Registers
  26. 25Inter-IC Sound (I2S)
    1. 25.1 Introduction
    2. 25.2 Block Diagram
    3. 25.3 Signal Description
    4. 25.4 Functional Description
      1. 25.4.1 Dependencies
        1. 25.4.1.1 System CPU Deep-Sleep Mode
      2. 25.4.2 Pin Configuration
      3. 25.4.3 Serial Format Configuration
      4. 25.4.4 I2S
        1. 25.4.4.1 Register Configuration
      5. 25.4.5 Left-Justified (LJF)
        1. 25.4.5.1 Register Configuration
      6. 25.4.6 Right-Justified (RJF)
        1. 25.4.6.1 Register Configuration
      7. 25.4.7 DSP
        1. 25.4.7.1 Register Configuration
      8. 25.4.8 Clock Configuration
        1. 25.4.8.1 Internal Audio Clock Source
        2. 25.4.8.2 External Audio Clock Source
    5. 25.5 Memory Interface
      1. 25.5.1 Sample Word Length
      2. 25.5.2 Channel Mapping
      3. 25.5.3 Sample Storage in Memory
      4. 25.5.4 DMA Operation
        1. 25.5.4.1 Start-Up
        2. 25.5.4.2 Operation
        3. 25.5.4.3 Shutdown
    6. 25.6 Samplestamp Generator
      1. 25.6.1 Samplestamp Counters
      2. 25.6.2 Start-Up Triggers
      3. 25.6.3 Samplestamp Capture
      4. 25.6.4 Achieving Constant Audio Latency
    7. 25.7 Error Detection
    8. 25.8 Usage
      1. 25.8.1 Start-Up Sequence
      2. 25.8.2 Shutdown Sequence
    9. 25.9 I2S Registers
  27. 26Radio
    1. 26.1  RF Core
      1. 26.1.1 High-Level Description and Overview
    2. 26.2  Radio Doorbell
      1. 26.2.1 Special Boot Process
      2. 26.2.2 Command and Status Register and Events
      3. 26.2.3 RF Core Interrupts
        1. 26.2.3.1 RF Command and Packet Engine Interrupts
        2. 26.2.3.2 RF Core Hardware Interrupts
        3. 26.2.3.3 RF Core Command Acknowledge Interrupt
      4. 26.2.4 Radio Timer
        1. 26.2.4.1 Compare and Capture Events
        2. 26.2.4.2 Radio Timer Outputs
        3. 26.2.4.3 Synchronization with Real-Time Clock
    3. 26.3  RF Core HAL
      1. 26.3.1 Hardware Support
      2. 26.3.2 Firmware Support
        1. 26.3.2.1 Commands
        2. 26.3.2.2 Command Status
        3. 26.3.2.3 Interrupts
        4. 26.3.2.4 Passing Data
        5. 26.3.2.5 Command Scheduling
          1. 26.3.2.5.1 Triggers
          2. 26.3.2.5.2 Conditional Execution
          3. 26.3.2.5.3 Handling Before Start of Command
        6. 26.3.2.6 Command Data Structures
          1. 26.3.2.6.1 Radio Operation Command Structure
        7. 26.3.2.7 Data Entry Structures
          1. 26.3.2.7.1 Data Entry Queue
          2. 26.3.2.7.2 Data Entry
          3. 26.3.2.7.3 Pointer Entry
          4. 26.3.2.7.4 Partial Read RX Entry
        8. 26.3.2.8 External Signaling
      3. 26.3.3 Command Definitions
        1. 26.3.3.1 Protocol-Independent Radio Operation Commands
          1. 26.3.3.1.1  CMD_NOP: No Operation Command
          2. 26.3.3.1.2  CMD_RADIO_SETUP: Set Up Radio Settings Command
          3. 26.3.3.1.3  CMD_FS_POWERUP: Power Up Frequency Synthesizer
          4. 26.3.3.1.4  CMD_FS_POWERDOWN: Power Down Frequency Synthesizer
          5. 26.3.3.1.5  CMD_FS: Frequency Synthesizer Controls Command
          6. 26.3.3.1.6  CMD_FS_OFF: Turn Off Frequency Synthesizer
          7. 26.3.3.1.7  CMD_RX_TEST: Receiver Test Command
          8. 26.3.3.1.8  CMD_TX_TEST: Transmitter Test Command
          9. 26.3.3.1.9  CMD_SYNC_STOP_RAT: Synchronize and Stop Radio Timer Command
          10. 26.3.3.1.10 CMD_SYNC_START_RAT: Synchronously Start Radio Timer Command
          11. 26.3.3.1.11 CMD_COUNT: Counter Command
          12. 26.3.3.1.12 CMD_SCH_IMM: Run Immediate Command as Radio Operation
          13. 26.3.3.1.13 CMD_COUNT_BRANCH: Counter Command with Branch of Command Chain
          14. 26.3.3.1.14 CMD_PATTERN_CHECK: Check a Value in Memory Against a Pattern
        2. 26.3.3.2 Protocol-Independent Direct and Immediate Commands
          1. 26.3.3.2.1  CMD_ABORT: ABORT Command
          2. 26.3.3.2.2  CMD_STOP: Stop Command
          3. 26.3.3.2.3  CMD_GET_RSSI: Read RSSI Command
          4. 26.3.3.2.4  CMD_UPDATE_RADIO_SETUP: Update Radio Settings Command
          5. 26.3.3.2.5  CMD_TRIGGER: Generate Command Trigger
          6. 26.3.3.2.6  CMD_GET_FW_INFO: Request Information on the Firmware Being Run
          7. 26.3.3.2.7  CMD_START_RAT: Asynchronously Start Radio Timer Command
          8. 26.3.3.2.8  CMD_PING: Respond with Interrupt
          9. 26.3.3.2.9  CMD_READ_RFREG: Read RF Core Register
          10. 26.3.3.2.10 CMD_SET_RAT_CMP: Set RAT Channel to Compare Mode
          11. 26.3.3.2.11 CMD_SET_RAT_CPT: Set RAT Channel to Capture Mode
          12. 26.3.3.2.12 CMD_DISABLE_RAT_CH: Disable RAT Channel
          13. 26.3.3.2.13 CMD_SET_RAT_OUTPUT: Set RAT Output to a Specified Mode
          14. 26.3.3.2.14 CMD_ARM_RAT_CH: Arm RAT Channel
          15. 26.3.3.2.15 CMD_DISARM_RAT_CH: Disarm RAT Channel
          16. 26.3.3.2.16 CMD_SET_TX_POWER: Set Transmit Power
          17. 26.3.3.2.17 CMD_SET_TX20_POWER: Set Transmit Power of the 20 dBm PA
          18. 26.3.3.2.18 CMD_MODIFY_FS: Set New Synthesizer Frequency Without Recalibration
          19. 26.3.3.2.19 CMD_BUS_REQUEST: Request System BUS Available for RF Core
      4. 26.3.4 Immediate Commands for Data Queue Manipulation
        1. 26.3.4.1 CMD_ADD_DATA_ENTRY: Add Data Entry to Queue
        2. 26.3.4.2 CMD_REMOVE_DATA_ENTRY: Remove First Data Entry from Queue
        3. 26.3.4.3 CMD_FLUSH_QUEUE: Flush Queue
        4. 26.3.4.4 CMD_CLEAR_RX: Clear All RX Queue Entries
        5. 26.3.4.5 CMD_REMOVE_PENDING_ENTRIES: Remove Pending Entries from Queue
    4. 26.4  Data Queue Usage
      1. 26.4.1 Operations on Data Queues Available Only for Internal Radio CPU Operations
        1. 26.4.1.1 PROC_ALLOCATE_TX: Allocate TX Entry for Reading
        2. 26.4.1.2 PROC_FREE_DATA_ENTRY: Free Allocated Data Entry
        3. 26.4.1.3 PROC_FINISH_DATA_ENTRY: Finish Use of First Data Entry From Queue
        4. 26.4.1.4 PROC_ALLOCATE_RX: Allocate RX Buffer for Storing Data
        5. 26.4.1.5 PROC_FINISH_RX: Commit Received Data to RX Data Entry
      2. 26.4.2 Radio CPU Usage Model
        1. 26.4.2.1 Receive Queues
        2. 26.4.2.2 Transmit Queues
    5. 26.5  IEEE 802.15.4
      1. 26.5.1 IEEE 802.15.4 Commands
        1. 26.5.1.1 IEEE 802.15.4 Radio Operation Command Structures
        2. 26.5.1.2 IEEE 802.15.4 Immediate Command Structures
        3. 26.5.1.3 Output Structures
        4. 26.5.1.4 Other Structures and Bit Fields
      2. 26.5.2 Interrupts
      3. 26.5.3 Data Handling
        1. 26.5.3.1 Receive Buffers
        2. 26.5.3.2 Transmit Buffers
      4. 26.5.4 Radio Operation Commands
        1. 26.5.4.1 RX Operation
          1. 26.5.4.1.1 Frame Filtering and Source Matching
            1. 26.5.4.1.1.1 Frame Filtering
            2. 26.5.4.1.1.2 Source Matching
          2. 26.5.4.1.2 Frame Reception
          3. 26.5.4.1.3 ACK Transmission
          4. 26.5.4.1.4 End of Receive Operation
          5. 26.5.4.1.5 CCA Monitoring
        2. 26.5.4.2 Energy Detect Scan Operation
        3. 26.5.4.3 CSMA-CA Operation
        4. 26.5.4.4 Transmit Operation
        5. 26.5.4.5 Receive Acknowledgment Operation
        6. 26.5.4.6 Abort Background-Level Operation Command
      5. 26.5.5 Immediate Commands
        1. 26.5.5.1 Modify CCA Parameter Command
        2. 26.5.5.2 Modify Frame-Filtering Parameter Command
        3. 26.5.5.3 Enable or Disable Source Matching Entry Command
        4. 26.5.5.4 Abort Foreground-Level Operation Command
        5. 26.5.5.5 Stop Foreground-Level Operation Command
        6. 26.5.5.6 Request CCA and RSSI Information Command
    6. 26.6  BluetoothĀ® Low Energy
      1. 26.6.1 BluetoothĀ® Low Energy Commands
        1. 26.6.1.1 Command Data Definitions
          1. 26.6.1.1.1 BluetoothĀ® Low Energy Command Structures
        2. 26.6.1.2 Parameter Structures
        3. 26.6.1.3 Output Structures
        4. 26.6.1.4 Other Structures and Bit Fields
      2. 26.6.2 Interrupts
    7. 26.7  Data Handling
      1. 26.7.1 Receive Buffers
      2. 26.7.2 Transmit Buffers
    8. 26.8  Radio Operation Command Descriptions
      1. 26.8.1  BluetoothĀ® 5 Radio Setup Command
      2. 26.8.2  Radio Operation Commands for BluetoothĀ® Low Energy Packet Transfer
      3. 26.8.3  Coding Selection for Coded PHY
      4. 26.8.4  Parameter Override
      5. 26.8.5  Link Layer Connection
      6. 26.8.6  Slave Command
      7. 26.8.7  Master Command
      8. 26.8.8  Legacy Advertiser
        1. 26.8.8.1 Connectable Undirected Advertiser Command
        2. 26.8.8.2 Connectable Directed Advertiser Command
        3. 26.8.8.3 Non-connectable Advertiser Command
        4. 26.8.8.4 Scannable Undirected Advertiser Command
      9. 26.8.9  BluetoothĀ® 5 Advertiser Commands
        1. 26.8.9.1 Common Extended Advertising Packets
        2. 26.8.9.2 Extended Advertiser Command
        3. 26.8.9.3 Secondary Channel Advertiser Command
      10. 26.8.10 Scanner Commands
        1. 26.8.10.1 Scanner Receiving Legacy Advertising Packets on Primary Channel
        2. 26.8.10.2 Scanner Receiving Extended Advertising Packets on Primary Channel
        3. 26.8.10.3 Scanner Receiving Extended Advertising Packets on Secondary Channel
        4. 26.8.10.4 ADI Filtering
        5. 26.8.10.5 End of Scanner Commands
      11. 26.8.11 Initiator Command
        1. 26.8.11.1 Initiator Receiving Legacy Advertising Packets on Primary Channel
        2. 26.8.11.2 Initiator Receiving Extended Advertising Packets on Primary Channel
        3. 26.8.11.3 Initiator Receiving Extended Advertising Packets on Secondary Channel
        4. 26.8.11.4 Automatic Window Offset Insertion
        5. 26.8.11.5 End of Initiator Commands
      12. 26.8.12 Generic Receiver Command
      13. 26.8.13 PHY Test Transmit Command
      14. 26.8.14 Whitelist Processing
      15. 26.8.15 Backoff Procedure
      16. 26.8.16 AUX Pointer Processing
      17. 26.8.17 Dynamic Change of Device Address
    9. 26.9  Immediate Commands
      1. 26.9.1 Update Advertising Payload Command
    10. 26.10 Proprietary Radio
      1. 26.10.1 Packet Formats
      2. 26.10.2 Commands
        1. 26.10.2.1 Command Data Definitions
          1. 26.10.2.1.1 Command Structures
        2. 26.10.2.2 Output Structures
        3. 26.10.2.3 Other Structures and Bit Fields
      3. 26.10.3 Interrupts
      4. 26.10.4 Data Handling
        1. 26.10.4.1 Receive Buffers
        2. 26.10.4.2 Transmit Buffers
      5. 26.10.5 Radio Operation Command Descriptions
        1. 26.10.5.1 End of Operation
        2. 26.10.5.2 Proprietary Mode Setup Command
          1. 26.10.5.2.1 IEEE 802.15.4g Packet Format
        3. 26.10.5.3 Transmitter Commands
          1. 26.10.5.3.1 Standard Transmit Command, CMD_PROP_TX
          2. 26.10.5.3.2 Advanced Transmit Command, CMD_PROP_TX_ADV
        4. 26.10.5.4 Receiver Commands
          1. 26.10.5.4.1 Standard Receive Command, CMD_PROP_RX
          2. 26.10.5.4.2 Advanced Receive Command, CMD_PROP_RX_ADV
        5. 26.10.5.5 Carrier-Sense Operation
          1. 26.10.5.5.1 Common Carrier-Sense Description
          2. 26.10.5.5.2 Carrier-Sense Command, CMD_PROP_CS
          3. 26.10.5.5.3 Sniff Mode Receiver Commands, CMD_PROP_RX_SNIFF and CMD_PROP_RX_ADV_SNIFF
      6. 26.10.6 Immediate Commands
        1. 26.10.6.1 Set Packet Length Command, CMD_PROP_SET_LEN
        2. 26.10.6.2 Restart Packet RX Command, CMD_PROP_RESTART_RX
    11. 26.11 Radio Registers
      1. 26.11.1 RFC_RAT Registers
      2. 26.11.2 RFC_DBELL Registers
      3. 26.11.3 RFC_PWR Registers
  28. 27Revision History

2.5.1 CPU_ITM Registers

Table 2-2 lists the memory-mapped registers for the CPU_ITM registers. All register offset addresses not listed in Table 2-2 should be considered as reserved locations and the register contents should not be modified.

Table 2-2 CPU_ITM Registers
Offset Acronym Register Name Section
0h STIM0 Provides the interface for generating Instrumentation packets Section 2.5.1.1
4h STIM1 Provides the interface for generating Instrumentation packets Section 2.5.1.2
8h STIM2 Provides the interface for generating Instrumentation packets Section 2.5.1.3
Ch STIM3 Provides the interface for generating Instrumentation packets Section 2.5.1.4
10h STIM4 Provides the interface for generating Instrumentation packets Section 2.5.1.5
14h STIM5 Provides the interface for generating Instrumentation packets Section 2.5.1.6
18h STIM6 Provides the interface for generating Instrumentation packets Section 2.5.1.7
1Ch STIM7 Provides the interface for generating Instrumentation packets Section 2.5.1.8
20h STIM8 Provides the interface for generating Instrumentation packets Section 2.5.1.9
24h STIM9 Provides the interface for generating Instrumentation packets Section 2.5.1.10
28h STIM10 Provides the interface for generating Instrumentation packets Section 2.5.1.11
2Ch STIM11 Provides the interface for generating Instrumentation packets Section 2.5.1.12
30h STIM12 Provides the interface for generating Instrumentation packets Section 2.5.1.13
34h STIM13 Provides the interface for generating Instrumentation packets Section 2.5.1.14
38h STIM14 Provides the interface for generating Instrumentation packets Section 2.5.1.15
3Ch STIM15 Provides the interface for generating Instrumentation packets Section 2.5.1.16
40h STIM16 Provides the interface for generating Instrumentation packets Section 2.5.1.17
44h STIM17 Provides the interface for generating Instrumentation packets Section 2.5.1.18
48h STIM18 Provides the interface for generating Instrumentation packets Section 2.5.1.19
4Ch STIM19 Provides the interface for generating Instrumentation packets Section 2.5.1.20
50h STIM20 Provides the interface for generating Instrumentation packets Section 2.5.1.21
54h STIM21 Provides the interface for generating Instrumentation packets Section 2.5.1.22
58h STIM22 Provides the interface for generating Instrumentation packets Section 2.5.1.23
5Ch STIM23 Provides the interface for generating Instrumentation packets Section 2.5.1.24
60h STIM24 Provides the interface for generating Instrumentation packets Section 2.5.1.25
64h STIM25 Provides the interface for generating Instrumentation packets Section 2.5.1.26
68h STIM26 Provides the interface for generating Instrumentation packets Section 2.5.1.27
6Ch STIM27 Provides the interface for generating Instrumentation packets Section 2.5.1.28
70h STIM28 Provides the interface for generating Instrumentation packets Section 2.5.1.29
74h STIM29 Provides the interface for generating Instrumentation packets Section 2.5.1.30
78h STIM30 Provides the interface for generating Instrumentation packets Section 2.5.1.31
7Ch STIM31 Provides the interface for generating Instrumentation packets Section 2.5.1.32
E00h TER0 Provide an individual enable bit for each ITM_STIM register Section 2.5.1.33
E40h TPR Controls which stimulus ports can be accessed by unprivileged code Section 2.5.1.34
E80h TCR Configures and controls transfers through the ITM interface Section 2.5.1.35
EF0h INT_ATREADY Integration Mode: Read ATB Ready Section 2.5.1.36
EF8h INT_ATVALID Integration Mode: Write ATB Valid Section 2.5.1.37
F00h ITCTRL Integration Mode Control Register Section 2.5.1.38
FBCh DEVARCH Provides CoreSight discovery information for the ITM Section 2.5.1.39
FCCh DEVTYPE Provides CoreSight discovery information for the ITM Section 2.5.1.40
FD0h PIDR4 Provides CoreSight discovery information for the ITM Section 2.5.1.41
FD4h PIDR5 Provides CoreSight discovery information for the ITM Section 2.5.1.42
FD8h PIDR6 Provides CoreSight discovery information for the ITM Section 2.5.1.43
FDCh PIDR7 Provides CoreSight discovery information for the ITM Section 2.5.1.44
FE0h PIDR0 Provides CoreSight discovery information for the ITM Section 2.5.1.45
FE4h PIDR1 Provides CoreSight discovery information for the ITM Section 2.5.1.46
FE8h PIDR2 Provides CoreSight discovery information for the ITM Section 2.5.1.47
FECh PIDR3 Provides CoreSight discovery information for the ITM Section 2.5.1.48
FF0h CIDR0 Provides CoreSight discovery information for the ITM Section 2.5.1.49
FF4h CIDR1 Provides CoreSight discovery information for the ITM Section 2.5.1.50
FF8h CIDR2 Provides CoreSight discovery information for the ITM Section 2.5.1.51
FFCh CIDR3 Provides CoreSight discovery information for the ITM Section 2.5.1.52

Complex bit access types are encoded to fit into small table cells. Table 2-3 shows the codes that are used for access types in this section.

Table 2-3 CPU_ITM Access Type Codes
Access Type Code Description
Read Type
R R Read
Write Type
W W Write
Reset or Default Value
-n Value after reset or the default value

2.5.1.1 STIM0 Register (Offset = 0h) [Reset = 00000000h]

STIM0 is shown in Table 2-4.

Return to the Summary Table.

Provides the interface for generating Instrumentation packets

Table 2-4 STIM0 Register Field Descriptions
Bit Field Type Reset Description
31-2 RESERVED R 0h Software should not rely on the value of a reserved. Writing any other value than the reset value may result in undefined behavior.
1 DISABLED R 0h Indicates whether the Stimulus Port is enabled or disabled
0 FIFOREADY R 0h Indicates whether the Stimulus Port can accept data

2.5.1.2 STIM1 Register (Offset = 4h) [Reset = 00000000h]

STIM1 is shown in Table 2-5.

Return to the Summary Table.

Provides the interface for generating Instrumentation packets

Table 2-5 STIM1 Register Field Descriptions
Bit Field Type Reset Description
31-2 RESERVED R 0h Software should not rely on the value of a reserved. Writing any other value than the reset value may result in undefined behavior.
1 DISABLED R 0h Indicates whether the Stimulus Port is enabled or disabled
0 FIFOREADY R 0h Indicates whether the Stimulus Port can accept data

2.5.1.3 STIM2 Register (Offset = 8h) [Reset = 00000000h]

STIM2 is shown in Table 2-6.

Return to the Summary Table.

Provides the interface for generating Instrumentation packets

Table 2-6 STIM2 Register Field Descriptions
Bit Field Type Reset Description
31-2 RESERVED R 0h Software should not rely on the value of a reserved. Writing any other value than the reset value may result in undefined behavior.
1 DISABLED R 0h Indicates whether the Stimulus Port is enabled or disabled
0 FIFOREADY R 0h Indicates whether the Stimulus Port can accept data

2.5.1.4 STIM3 Register (Offset = Ch) [Reset = 00000000h]

STIM3 is shown in Table 2-7.

Return to the Summary Table.

Provides the interface for generating Instrumentation packets

Table 2-7 STIM3 Register Field Descriptions
Bit Field Type Reset Description
31-2 RESERVED R 0h Software should not rely on the value of a reserved. Writing any other value than the reset value may result in undefined behavior.
1 DISABLED R 0h Indicates whether the Stimulus Port is enabled or disabled
0 FIFOREADY R 0h Indicates whether the Stimulus Port can accept data

2.5.1.5 STIM4 Register (Offset = 10h) [Reset = 00000000h]

STIM4 is shown in Table 2-8.

Return to the Summary Table.

Provides the interface for generating Instrumentation packets

Table 2-8 STIM4 Register Field Descriptions
Bit Field Type Reset Description
31-2 RESERVED R 0h Software should not rely on the value of a reserved. Writing any other value than the reset value may result in undefined behavior.
1 DISABLED R 0h Indicates whether the Stimulus Port is enabled or disabled
0 FIFOREADY R 0h Indicates whether the Stimulus Port can accept data

2.5.1.6 STIM5 Register (Offset = 14h) [Reset = 00000000h]

STIM5 is shown in Table 2-9.

Return to the Summary Table.

Provides the interface for generating Instrumentation packets

Table 2-9 STIM5 Register Field Descriptions
Bit Field Type Reset Description
31-2 RESERVED R 0h Software should not rely on the value of a reserved. Writing any other value than the reset value may result in undefined behavior.
1 DISABLED R 0h Indicates whether the Stimulus Port is enabled or disabled
0 FIFOREADY R 0h Indicates whether the Stimulus Port can accept data

2.5.1.7 STIM6 Register (Offset = 18h) [Reset = 00000000h]

STIM6 is shown in Table 2-10.

Return to the Summary Table.

Provides the interface for generating Instrumentation packets

Table 2-10 STIM6 Register Field Descriptions
Bit Field Type Reset Description
31-2 RESERVED R 0h Software should not rely on the value of a reserved. Writing any other value than the reset value may result in undefined behavior.
1 DISABLED R 0h Indicates whether the Stimulus Port is enabled or disabled
0 FIFOREADY R 0h Indicates whether the Stimulus Port can accept data

2.5.1.8 STIM7 Register (Offset = 1Ch) [Reset = 00000000h]

STIM7 is shown in Table 2-11.

Return to the Summary Table.

Provides the interface for generating Instrumentation packets

Table 2-11 STIM7 Register Field Descriptions
Bit Field Type Reset Description
31-2 RESERVED R 0h Software should not rely on the value of a reserved. Writing any other value than the reset value may result in undefined behavior.
1 DISABLED R 0h Indicates whether the Stimulus Port is enabled or disabled
0 FIFOREADY R 0h Indicates whether the Stimulus Port can accept data

2.5.1.9 STIM8 Register (Offset = 20h) [Reset = 00000000h]

STIM8 is shown in Table 2-12.

Return to the Summary Table.

Provides the interface for generating Instrumentation packets

Table 2-12 STIM8 Register Field Descriptions
Bit Field Type Reset Description
31-2 RESERVED R 0h Software should not rely on the value of a reserved. Writing any other value than the reset value may result in undefined behavior.
1 DISABLED R 0h Indicates whether the Stimulus Port is enabled or disabled
0 FIFOREADY R 0h Indicates whether the Stimulus Port can accept data

2.5.1.10 STIM9 Register (Offset = 24h) [Reset = 00000000h]

STIM9 is shown in Table 2-13.

Return to the Summary Table.

Provides the interface for generating Instrumentation packets

Table 2-13 STIM9 Register Field Descriptions
Bit Field Type Reset Description
31-2 RESERVED R 0h Software should not rely on the value of a reserved. Writing any other value than the reset value may result in undefined behavior.
1 DISABLED R 0h Indicates whether the Stimulus Port is enabled or disabled
0 FIFOREADY R 0h Indicates whether the Stimulus Port can accept data

2.5.1.11 STIM10 Register (Offset = 28h) [Reset = 00000000h]

STIM10 is shown in Table 2-14.

Return to the Summary Table.

Provides the interface for generating Instrumentation packets

Table 2-14 STIM10 Register Field Descriptions
Bit Field Type Reset Description
31-2 RESERVED R 0h Software should not rely on the value of a reserved. Writing any other value than the reset value may result in undefined behavior.
1 DISABLED R 0h Indicates whether the Stimulus Port is enabled or disabled
0 FIFOREADY R 0h Indicates whether the Stimulus Port can accept data

2.5.1.12 STIM11 Register (Offset = 2Ch) [Reset = 00000000h]

STIM11 is shown in Table 2-15.

Return to the Summary Table.

Provides the interface for generating Instrumentation packets

Table 2-15 STIM11 Register Field Descriptions
Bit Field Type Reset Description
31-2 RESERVED R 0h Software should not rely on the value of a reserved. Writing any other value than the reset value may result in undefined behavior.
1 DISABLED R 0h Indicates whether the Stimulus Port is enabled or disabled
0 FIFOREADY R 0h Indicates whether the Stimulus Port can accept data

2.5.1.13 STIM12 Register (Offset = 30h) [Reset = 00000000h]

STIM12 is shown in Table 2-16.

Return to the Summary Table.

Provides the interface for generating Instrumentation packets

Table 2-16 STIM12 Register Field Descriptions
Bit Field Type Reset Description
31-2 RESERVED R 0h Software should not rely on the value of a reserved. Writing any other value than the reset value may result in undefined behavior.
1 DISABLED R 0h Indicates whether the Stimulus Port is enabled or disabled
0 FIFOREADY R 0h Indicates whether the Stimulus Port can accept data

2.5.1.14 STIM13 Register (Offset = 34h) [Reset = 00000000h]

STIM13 is shown in Table 2-17.

Return to the Summary Table.

Provides the interface for generating Instrumentation packets

Table 2-17 STIM13 Register Field Descriptions
Bit Field Type Reset Description
31-2 RESERVED R 0h Software should not rely on the value of a reserved. Writing any other value than the reset value may result in undefined behavior.
1 DISABLED R 0h Indicates whether the Stimulus Port is enabled or disabled
0 FIFOREADY R 0h Indicates whether the Stimulus Port can accept data

2.5.1.15 STIM14 Register (Offset = 38h) [Reset = 00000000h]

STIM14 is shown in Table 2-18.

Return to the Summary Table.

Provides the interface for generating Instrumentation packets

Table 2-18 STIM14 Register Field Descriptions
Bit Field Type Reset Description
31-2 RESERVED R 0h Software should not rely on the value of a reserved. Writing any other value than the reset value may result in undefined behavior.
1 DISABLED R 0h Indicates whether the Stimulus Port is enabled or disabled
0 FIFOREADY R 0h Indicates whether the Stimulus Port can accept data

2.5.1.16 STIM15 Register (Offset = 3Ch) [Reset = 00000000h]

STIM15 is shown in Table 2-19.

Return to the Summary Table.

Provides the interface for generating Instrumentation packets

Table 2-19 STIM15 Register Field Descriptions
Bit Field Type Reset Description
31-2 RESERVED R 0h Software should not rely on the value of a reserved. Writing any other value than the reset value may result in undefined behavior.
1 DISABLED R 0h Indicates whether the Stimulus Port is enabled or disabled
0 FIFOREADY R 0h Indicates whether the Stimulus Port can accept data

2.5.1.17 STIM16 Register (Offset = 40h) [Reset = 00000000h]

STIM16 is shown in Table 2-20.

Return to the Summary Table.

Provides the interface for generating Instrumentation packets

Table 2-20 STIM16 Register Field Descriptions
Bit Field Type Reset Description
31-2 RESERVED R 0h Software should not rely on the value of a reserved. Writing any other value than the reset value may result in undefined behavior.
1 DISABLED R 0h Indicates whether the Stimulus Port is enabled or disabled
0 FIFOREADY R 0h Indicates whether the Stimulus Port can accept data

2.5.1.18 STIM17 Register (Offset = 44h) [Reset = 00000000h]

STIM17 is shown in Table 2-21.

Return to the Summary Table.

Provides the interface for generating Instrumentation packets

Table 2-21 STIM17 Register Field Descriptions
Bit Field Type Reset Description
31-2 RESERVED R 0h Software should not rely on the value of a reserved. Writing any other value than the reset value may result in undefined behavior.
1 DISABLED R 0h Indicates whether the Stimulus Port is enabled or disabled
0 FIFOREADY R 0h Indicates whether the Stimulus Port can accept data

2.5.1.19 STIM18 Register (Offset = 48h) [Reset = 00000000h]

STIM18 is shown in Table 2-22.

Return to the Summary Table.

Provides the interface for generating Instrumentation packets

Table 2-22 STIM18 Register Field Descriptions
Bit Field Type Reset Description
31-2 RESERVED R 0h Software should not rely on the value of a reserved. Writing any other value than the reset value may result in undefined behavior.
1 DISABLED R 0h Indicates whether the Stimulus Port is enabled or disabled
0 FIFOREADY R 0h Indicates whether the Stimulus Port can accept data

2.5.1.20 STIM19 Register (Offset = 4Ch) [Reset = 00000000h]

STIM19 is shown in Table 2-23.

Return to the Summary Table.

Provides the interface for generating Instrumentation packets

Table 2-23 STIM19 Register Field Descriptions
Bit Field Type Reset Description
31-2 RESERVED R 0h Software should not rely on the value of a reserved. Writing any other value than the reset value may result in undefined behavior.
1 DISABLED R 0h Indicates whether the Stimulus Port is enabled or disabled
0 FIFOREADY R 0h Indicates whether the Stimulus Port can accept data

2.5.1.21 STIM20 Register (Offset = 50h) [Reset = 00000000h]

STIM20 is shown in Table 2-24.

Return to the Summary Table.

Provides the interface for generating Instrumentation packets

Table 2-24 STIM20 Register Field Descriptions
Bit Field Type Reset Description
31-2 RESERVED R 0h Software should not rely on the value of a reserved. Writing any other value than the reset value may result in undefined behavior.
1 DISABLED R 0h Indicates whether the Stimulus Port is enabled or disabled
0 FIFOREADY R 0h Indicates whether the Stimulus Port can accept data

2.5.1.22 STIM21 Register (Offset = 54h) [Reset = 00000000h]

STIM21 is shown in Table 2-25.

Return to the Summary Table.

Provides the interface for generating Instrumentation packets

Table 2-25 STIM21 Register Field Descriptions
Bit Field Type Reset Description
31-2 RESERVED R 0h Software should not rely on the value of a reserved. Writing any other value than the reset value may result in undefined behavior.
1 DISABLED R 0h Indicates whether the Stimulus Port is enabled or disabled
0 FIFOREADY R 0h Indicates whether the Stimulus Port can accept data

2.5.1.23 STIM22 Register (Offset = 58h) [Reset = 00000000h]

STIM22 is shown in Table 2-26.

Return to the Summary Table.

Provides the interface for generating Instrumentation packets

Table 2-26 STIM22 Register Field Descriptions
Bit Field Type Reset Description
31-2 RESERVED R 0h Software should not rely on the value of a reserved. Writing any other value than the reset value may result in undefined behavior.
1 DISABLED R 0h Indicates whether the Stimulus Port is enabled or disabled
0 FIFOREADY R 0h Indicates whether the Stimulus Port can accept data

2.5.1.24 STIM23 Register (Offset = 5Ch) [Reset = 00000000h]

STIM23 is shown in Table 2-27.

Return to the Summary Table.

Provides the interface for generating Instrumentation packets

Table 2-27 STIM23 Register Field Descriptions
Bit Field Type Reset Description
31-2 RESERVED R 0h Software should not rely on the value of a reserved. Writing any other value than the reset value may result in undefined behavior.
1 DISABLED R 0h Indicates whether the Stimulus Port is enabled or disabled
0 FIFOREADY R 0h Indicates whether the Stimulus Port can accept data

2.5.1.25 STIM24 Register (Offset = 60h) [Reset = 00000000h]

STIM24 is shown in Table 2-28.

Return to the Summary Table.

Provides the interface for generating Instrumentation packets

Table 2-28 STIM24 Register Field Descriptions
Bit Field Type Reset Description
31-2 RESERVED R 0h Software should not rely on the value of a reserved. Writing any other value than the reset value may result in undefined behavior.
1 DISABLED R 0h Indicates whether the Stimulus Port is enabled or disabled
0 FIFOREADY R 0h Indicates whether the Stimulus Port can accept data

2.5.1.26 STIM25 Register (Offset = 64h) [Reset = 00000000h]

STIM25 is shown in Table 2-29.

Return to the Summary Table.

Provides the interface for generating Instrumentation packets

Table 2-29 STIM25 Register Field Descriptions
Bit Field Type Reset Description
31-2 RESERVED R 0h Software should not rely on the value of a reserved. Writing any other value than the reset value may result in undefined behavior.
1 DISABLED R 0h Indicates whether the Stimulus Port is enabled or disabled
0 FIFOREADY R 0h Indicates whether the Stimulus Port can accept data

2.5.1.27 STIM26 Register (Offset = 68h) [Reset = 00000000h]

STIM26 is shown in Table 2-30.

Return to the Summary Table.

Provides the interface for generating Instrumentation packets

Table 2-30 STIM26 Register Field Descriptions
Bit Field Type Reset Description
31-2 RESERVED R 0h Software should not rely on the value of a reserved. Writing any other value than the reset value may result in undefined behavior.
1 DISABLED R 0h Indicates whether the Stimulus Port is enabled or disabled
0 FIFOREADY R 0h Indicates whether the Stimulus Port can accept data

2.5.1.28 STIM27 Register (Offset = 6Ch) [Reset = 00000000h]

STIM27 is shown in Table 2-31.

Return to the Summary Table.

Provides the interface for generating Instrumentation packets

Table 2-31 STIM27 Register Field Descriptions
Bit Field Type Reset Description
31-2 RESERVED R 0h Software should not rely on the value of a reserved. Writing any other value than the reset value may result in undefined behavior.
1 DISABLED R 0h Indicates whether the Stimulus Port is enabled or disabled
0 FIFOREADY R 0h Indicates whether the Stimulus Port can accept data

2.5.1.29 STIM28 Register (Offset = 70h) [Reset = 00000000h]

STIM28 is shown in Table 2-32.

Return to the Summary Table.

Provides the interface for generating Instrumentation packets

Table 2-32 STIM28 Register Field Descriptions
Bit Field Type Reset Description
31-2 RESERVED R 0h Software should not rely on the value of a reserved. Writing any other value than the reset value may result in undefined behavior.
1 DISABLED R 0h Indicates whether the Stimulus Port is enabled or disabled
0 FIFOREADY R 0h Indicates whether the Stimulus Port can accept data

2.5.1.30 STIM29 Register (Offset = 74h) [Reset = 00000000h]

STIM29 is shown in Table 2-33.

Return to the Summary Table.

Provides the interface for generating Instrumentation packets

Table 2-33 STIM29 Register Field Descriptions
Bit Field Type Reset Description
31-2 RESERVED R 0h Software should not rely on the value of a reserved. Writing any other value than the reset value may result in undefined behavior.
1 DISABLED R 0h Indicates whether the Stimulus Port is enabled or disabled
0 FIFOREADY R 0h Indicates whether the Stimulus Port can accept data

2.5.1.31 STIM30 Register (Offset = 78h) [Reset = 00000000h]

STIM30 is shown in Table 2-34.

Return to the Summary Table.

Provides the interface for generating Instrumentation packets

Table 2-34 STIM30 Register Field Descriptions
Bit Field Type Reset Description
31-2 RESERVED R 0h Software should not rely on the value of a reserved. Writing any other value than the reset value may result in undefined behavior.
1 DISABLED R 0h Indicates whether the Stimulus Port is enabled or disabled
0 FIFOREADY R 0h Indicates whether the Stimulus Port can accept data

2.5.1.32 STIM31 Register (Offset = 7Ch) [Reset = 00000000h]

STIM31 is shown in Table 2-35.

Return to the Summary Table.

Provides the interface for generating Instrumentation packets

Table 2-35 STIM31 Register Field Descriptions
Bit Field Type Reset Description
31-2 RESERVED R 0h Software should not rely on the value of a reserved. Writing any other value than the reset value may result in undefined behavior.
1 DISABLED R 0h Indicates whether the Stimulus Port is enabled or disabled
0 FIFOREADY R 0h Indicates whether the Stimulus Port can accept data

2.5.1.33 TER0 Register (Offset = E00h) [Reset = 00000000h]

TER0 is shown in Table 2-36.

Return to the Summary Table.

Provide an individual enable bit for each ITM_STIM register

Table 2-36 TER0 Register Field Descriptions
Bit Field Type Reset Description
31-0 STIMENA R/W 0h For STIMENA[m] in ITM_TER*n, controls whether ITM_STIM(32*n + m) is enabled

2.5.1.34 TPR Register (Offset = E40h) [Reset = 00000000h]

TPR is shown in Table 2-37.

Return to the Summary Table.

Controls which stimulus ports can be accessed by unprivileged code

Table 2-37 TPR Register Field Descriptions
Bit Field Type Reset Description
31-0 PRIVMASK R/W 0h For PRIVMASK[m], defines the access permissions of ITM_STIM Stimulus Ports 8m to 8m+7 inclusive

2.5.1.35 TCR Register (Offset = E80h) [Reset = 00000000h]

TCR is shown in Table 2-38.

Return to the Summary Table.

Configures and controls transfers through the ITM interface

Table 2-38 TCR Register Field Descriptions
Bit Field Type Reset Description
31-24 RESERVED R 0h Software should not rely on the value of a reserved. Writing any other value than the reset value may result in undefined behavior.
23 BUSY R 0h Indicates whether the ITM is currently processing events
22-16 TraceBusID R/W 0h Identifier for multi-source trace stream formatting. If multi-source trace is in use, the debugger must write a unique non-zero trace ID value to this field
15-12 RESERVED R 0h Software should not rely on the value of a reserved. Writing any other value than the reset value may result in undefined behavior.
11-10 GTSFREQ R/W 0h Defines how often the ITM generates a global timestamp, based on the global timestamp clock frequency, or disables generation of global timestamps
9-8 TSPrescale R/W 0h Local timestamp prescaler, used with the trace packet reference clock
7-6 RESERVED R 0h Software should not rely on the value of a reserved. Writing any other value than the reset value may result in undefined behavior.
5 STALLENA R/W 0h Stall the PE to guarantee delivery of Data Trace packets.
4 SWOENA R/W 0h Enables asynchronous clocking of the timestamp counter
3 TXENA R/W 0h Enables forwarding of hardware event packet from the DWT unit to the ITM for output to the TPIU
2 SYNCENA R/W 0h Enables Synchronization packet transmission for a synchronous TPIU
1 TSENA R/W 0h Enables Local timestamp generation
0 ITMENA R/W 0h Enables the ITM

2.5.1.36 INT_ATREADY Register (Offset = EF0h) [Reset = 00000000h]

INT_ATREADY is shown in Table 2-39.

Return to the Summary Table.

Integration Mode: Read ATB Ready

Table 2-39 INT_ATREADY Register Field Descriptions
Bit Field Type Reset Description
31-2 RESERVED R 0h Software should not rely on the value of a reserved. Writing any other value than the reset value may result in undefined behavior.
1 AFVALID R 0h A read of this bit returns the value of AFVALID
0 ATREADY R 0h A read of this bit returns the value of ATREADY

2.5.1.37 INT_ATVALID Register (Offset = EF8h) [Reset = 00000000h]

INT_ATVALID is shown in Table 2-40.

Return to the Summary Table.

Integration Mode: Write ATB Valid

Table 2-40 INT_ATVALID Register Field Descriptions
Bit Field Type Reset Description
31-2 RESERVED R 0h Software should not rely on the value of a reserved. Writing any other value than the reset value may result in undefined behavior.
1 AFREADY W 0h A write to this bit gives the value of AFREADY
0 ATREADY W 0h A write to this bit gives the value of ATVALID

2.5.1.38 ITCTRL Register (Offset = F00h) [Reset = 00000000h]

ITCTRL is shown in Table 2-41.

Return to the Summary Table.

Integration Mode Control Register

Table 2-41 ITCTRL Register Field Descriptions
Bit Field Type Reset Description
31-1 RESERVED R 0h Software should not rely on the value of a reserved. Writing any other value than the reset value may result in undefined behavior.
0 IME R/W 0h Integration mode enable bit - The possible values are: 0 - The trace unit is not in integration mode. 1 - The trace unit is in integration mode. This mode enables: A debug agent to perform topology detection. SoC test software to perform integration testing.

2.5.1.39 DEVARCH Register (Offset = FBCh) [Reset = 00000000h]

DEVARCH is shown in Table 2-42.

Return to the Summary Table.

Provides CoreSight discovery information for the ITM

Table 2-42 DEVARCH Register Field Descriptions
Bit Field Type Reset Description
31-21 ARCHITECT R 0h Defines the architect of the component. Bits [31:28] are the JEP106 continuation code (JEP106 bank ID, minus 1) and bits [27:21] are the JEP106 ID code.
20 PRESENT R 0h Defines that the DEVARCH register is present
19-16 REVISION R 0h Defines the architecture revision of the component
15-12 ARCHVER R 0h Defines the architecture version of the component
11-0 ARCHPART R 0h Defines the architecture of the component

2.5.1.40 DEVTYPE Register (Offset = FCCh) [Reset = 00000000h]

DEVTYPE is shown in Table 2-43.

Return to the Summary Table.

Provides CoreSight discovery information for the ITM

Table 2-43 DEVTYPE Register Field Descriptions
Bit Field Type Reset Description
31-8 RESERVED R 0h Software should not rely on the value of a reserved. Writing any other value than the reset value may result in undefined behavior.
7-4 SUB R 0h Component sub-type
3-0 MAJOR R 0h Component major type

2.5.1.41 PIDR4 Register (Offset = FD0h) [Reset = 00000000h]

PIDR4 is shown in Table 2-44.

Return to the Summary Table.

Provides CoreSight discovery information for the ITM

Table 2-44 PIDR4 Register Field Descriptions
Bit Field Type Reset Description
31-8 RESERVED R 0h Software should not rely on the value of a reserved. Writing any other value than the reset value may result in undefined behavior.
7-4 SIZE R 0h See CoreSight Architecture Specification
3-0 DES_2 R 0h See CoreSight Architecture Specification

2.5.1.42 PIDR5 Register (Offset = FD4h) [Reset = 00000000h]

PIDR5 is shown in Table 2-45.

Return to the Summary Table.

Provides CoreSight discovery information for the ITM

Table 2-45 PIDR5 Register Field Descriptions
Bit Field Type Reset Description
31-0 RESERVED R 0h Software should not rely on the value of a reserved. Writing any other value than the reset value may result in undefined behavior.

2.5.1.43 PIDR6 Register (Offset = FD8h) [Reset = 00000000h]

PIDR6 is shown in Table 2-46.

Return to the Summary Table.

Provides CoreSight discovery information for the ITM

Table 2-46 PIDR6 Register Field Descriptions
Bit Field Type Reset Description
31-0 RESERVED R 0h Software should not rely on the value of a reserved. Writing any other value than the reset value may result in undefined behavior.

2.5.1.44 PIDR7 Register (Offset = FDCh) [Reset = 00000000h]

PIDR7 is shown in Table 2-47.

Return to the Summary Table.

Provides CoreSight discovery information for the ITM

Table 2-47 PIDR7 Register Field Descriptions
Bit Field Type Reset Description
31-0 RESERVED R 0h Software should not rely on the value of a reserved. Writing any other value than the reset value may result in undefined behavior.

2.5.1.45 PIDR0 Register (Offset = FE0h) [Reset = 00000000h]

PIDR0 is shown in Table 2-48.

Return to the Summary Table.

Provides CoreSight discovery information for the ITM

Table 2-48 PIDR0 Register Field Descriptions
Bit Field Type Reset Description
31-8 RESERVED R 0h Software should not rely on the value of a reserved. Writing any other value than the reset value may result in undefined behavior.
7-0 PART_0 R 0h See CoreSight Architecture Specification

2.5.1.46 PIDR1 Register (Offset = FE4h) [Reset = 00000000h]

PIDR1 is shown in Table 2-49.

Return to the Summary Table.

Provides CoreSight discovery information for the ITM

Table 2-49 PIDR1 Register Field Descriptions
Bit Field Type Reset Description
31-8 RESERVED R 0h Software should not rely on the value of a reserved. Writing any other value than the reset value may result in undefined behavior.
7-4 DES_0 R 0h See CoreSight Architecture Specification
3-0 PART_1 R 0h See CoreSight Architecture Specification

2.5.1.47 PIDR2 Register (Offset = FE8h) [Reset = 00000000h]

PIDR2 is shown in Table 2-50.

Return to the Summary Table.

Provides CoreSight discovery information for the ITM

Table 2-50 PIDR2 Register Field Descriptions
Bit Field Type Reset Description
31-8 RESERVED R 0h Software should not rely on the value of a reserved. Writing any other value than the reset value may result in undefined behavior.
7-4 REVISION R 0h See CoreSight Architecture Specification
3 JEDEC R 0h See CoreSight Architecture Specification
2-0 DES_1 R 0h See CoreSight Architecture Specification

2.5.1.48 PIDR3 Register (Offset = FECh) [Reset = 00000000h]

PIDR3 is shown in Table 2-51.

Return to the Summary Table.

Provides CoreSight discovery information for the ITM

Table 2-51 PIDR3 Register Field Descriptions
Bit Field Type Reset Description
31-8 RESERVED R 0h Software should not rely on the value of a reserved. Writing any other value than the reset value may result in undefined behavior.
7-4 REVAND R 0h See CoreSight Architecture Specification
3-0 CMOD R 0h See CoreSight Architecture Specification

2.5.1.49 CIDR0 Register (Offset = FF0h) [Reset = 00000000h]

CIDR0 is shown in Table 2-52.

Return to the Summary Table.

Provides CoreSight discovery information for the ITM

Table 2-52 CIDR0 Register Field Descriptions
Bit Field Type Reset Description
31-8 RESERVED R 0h Software should not rely on the value of a reserved. Writing any other value than the reset value may result in undefined behavior.
7-0 PRMBL_0 R 0h See CoreSight Architecture Specification

2.5.1.50 CIDR1 Register (Offset = FF4h) [Reset = 00000000h]

CIDR1 is shown in Table 2-53.

Return to the Summary Table.

Provides CoreSight discovery information for the ITM

Table 2-53 CIDR1 Register Field Descriptions
Bit Field Type Reset Description
31-8 RESERVED R 0h Software should not rely on the value of a reserved. Writing any other value than the reset value may result in undefined behavior.
7-4 CLASS R 0h See CoreSight Architecture Specification
3-0 PRMBL_1 R 0h See CoreSight Architecture Specification

2.5.1.51 CIDR2 Register (Offset = FF8h) [Reset = 00000000h]

CIDR2 is shown in Table 2-54.

Return to the Summary Table.

Provides CoreSight discovery information for the ITM

Table 2-54 CIDR2 Register Field Descriptions
Bit Field Type Reset Description
31-8 RESERVED R 0h Software should not rely on the value of a reserved. Writing any other value than the reset value may result in undefined behavior.
7-0 PRMBL_2 R 0h See CoreSight Architecture Specification

2.5.1.52 CIDR3 Register (Offset = FFCh) [Reset = 00000000h]

CIDR3 is shown in Table 2-55.

Return to the Summary Table.

Provides CoreSight discovery information for the ITM

Table 2-55 CIDR3 Register Field Descriptions
Bit Field Type Reset Description
31-8 RESERVED R 0h Software should not rely on the value of a reserved. Writing any other value than the reset value may result in undefined behavior.
7-0 PRMBL_3 R 0h See CoreSight Architecture Specification