TMAG5170
- High-precision linear 3D Hall-effect sensor to optimize position sensing speed and accuracy:
- Linear measurement total error: ±2.6% (maximum at 25°C)
- Sensitivity temperature drift: ±2.8% (maximum)
- 20-Ksps conversion rate for single axis
- 10-MHz serial peripheral interface (SPI) with cyclic redundancy check (CRC)
- Built-in temperature sensor with < ±2°C error
- Independently selectable X, Y, and Z magnetic ranges:
- TMAG5170A1: ±25, ±50, ±100 mT
- TMAG5170A2: ±75, ±150, ±300 mT
- 5-nA (typical) deep sleep mode current
- Autonomous wake-up and sleep mode for threshold detection consuming only 1.5 µA
- ALERT function to initiate sensor conversion or indicate conversion complete
- Integrated diagnostics for fault detection
- Integrated angle CORDIC calculation with gain and offset adjustment
- 2.3-V to 5.5-V supply voltage range
- Operating temperature range: –40°C to +150°C
The TMAG5170 is a high-precision linear 3D Hall-effect sensor designed for a wide range of industrial and personal electronics applications. The high level of integration offers flexibility and accuracy in a variety of position sensing systems. This device features 3 independent Hall sensors at X, Y, and Z axes.
A precision signal-chain along with an integrated 12-bit ADC enables high accuracy and low drift magnetic field measurements while supporting a sampling of up to 20 ksps. On-chip temperature sensor data is available for system-level drift compensation.
Integrated angle calculation engine (CORDIC) provides full 360° angular position information for both on-axis and off-axis angle measurement topologies. The angle calculation is performed using two user-selected magnetic axes. The device features magnetic gain and offset correction to mitigate the impact of system mechanical error sources.
The TMAG5170 can be configured through the SPI to enable any combination of magnetic axes and temperature measurements. Multiple sensor conversion schemes and SPI read frames help optimize throughput and accuracy. A dedicated ALERT pin can act as a system interrupt during low power wake-up and sleep mode, and can also be used by a microcontroller to trigger a new sensor conversion.
The TMAG5170 offers multiple diagnostics features to detect and report both system and device-level failures. The SPI communication features a user-enabled cyclic redundancy check to enhance the data integrity.
The device is offered in two different orderables to support wide magnetic fields ranges from ±25mT to ±300mT.
The device performs consistently across a wide ambient temperature range of –40°C to +150°C.
TMAG5170은 측정 및 감지(ar Measurement & Sensing) 부문에서 Elektronik 선정 올해의 제품으로 뽑혔습니다.
관심 가지실만한 유사 제품
비교 대상 장치와 동일한 기능을 지원하는 핀 대 핀.
다른 핀 출력을 지원하지만 비교 대상 장치와 동일한 기능.
기술 자료
설계 및 개발
추가 조건 또는 필수 리소스는 사용 가능한 경우 아래 제목을 클릭하여 세부 정보 페이지를 확인하세요.
TMAG5170UEVM — TMAG5170 평가 모듈
TMAG5170-CODE-EXAMPLE — TMAG5170 and TMAG5170-Q1 C code example
TI-MAGNETIC-SENSE-SIMULATOR — TI Magnetic sensing simulation tool
HALL-PROXIMITY-DESIGN — Magnetic Sensing Proximity Tool
HALL-PROXIMITY-DESIGN은 자석 및 홀(Hall) 효과 센서 시스템을 위한 신속한 반복 설계를 도와주는 소프트웨어 도구입니다.
SBAR012 — Angle Error Calculator for Linear 3D Hall-effect Sensors
TIDA-010997 — 에지 AI 센서 BoosterPack™ 레퍼런스 설계
이 레퍼런스 설계는 여러 TI 평가 모듈(EVM)과 호환되는 플러그 앤 플레이 방식의 시계열 센서 BoosterPack™을 소개합니다. 이 설계는 다양한 센서 유형에 대한 직접 액세스를 제공하여 CCStudio™ Edge AI Studio를 사용한 에지 AI 애플리케이션 개발 및 평가를 위해 간편하게 데이터를 수집할 수 있습니다.
TIDA-060040 — 정밀한 모터 위치 제어를 위한 홀 효과 센서가 있는 절대각 인코더 레퍼런스 설계
TIDA-060040 레퍼런스 설계는 로봇 팔 제어와 같은 정밀 모터 제어 애플리케이션에서 일반적으로 사용되는 절대 각도 인코딩 방법을 보여줍니다. 각도 인코딩은 다양한 자기 감지 기술을 사용하여 달성할 수 있습니다. 이는 자연적으로 위상을 90° 벗어난 두 개의 자속 밀도, B 필드, 벡터 구성 요소를 감지하여 수행됩니다. 자석이 회전함에 따라 센서 입력은 정현파가 되므로 삼각법 특성을 사용한 계산이 가능합니다.
그러나 시스템의 전기적 및 기계적 특성으로 인해 최고의 정확도를 얻으려면 최종 결과를 수정해야 하는 경우가 많습니다. (...)
TIDA-060045 — 쿼드 3D 홀 효과 센서를 사용한 정확한 저지연 선형 위치 감지 레퍼런스 설계
| 패키지 | 핀 | CAD 기호, 풋프린트 및 3D 모델 |
|---|---|---|
| VSSOP (DGK) | 8 | Ultra Librarian |
주문 및 품질
권장 제품에는 본 TI 제품과 관련된 매개 변수, 평가 모듈 또는 레퍼런스 디자인이 있을 수 있습니다.