CC1201
- RF Performance and Analog Features:
- High-Performance,
Single-Chip Transceiver
- Excellent Receiver Sensitivity:
- –120 dBm at 1.2 kbps
- –109 dBm at 50 kbps
- Blocking Performance: 85 dB at 10 MHz
- Adjacent Channel Selectivity: Up to 62 dB at 50-kHz Offset
- Very Low Phase Noise: –114 dBc/Hz at
10-kHz Offset (169 MHz)
- Excellent Receiver Sensitivity:
- Programmable Output Power Up to +16 dBm With 0.4-dB Step Size
- Automatic Output Power Ramping
- Supported
Modulation Formats:
2-FSK, 2-GFSK, 4-FSK, 4-GFSK, MSK, OOK - Supports Data Rate Up to 1.25 Mbps in Transmit and Receive
- High-Performance,
Single-Chip Transceiver
- Low Current
Consumption:
- Enhanced Wake-On-Radio (eWOR) Functionality for Automatic Low-Power Receive Polling
- Power Down: 0.12 μA (0.5 μA With eWOR Timer
Active)
- RX: 0.5 mA in RX Sniff Mode
- RX: 19 mA Peak Current in Low-Power Mode
- RX: 23 mA Peak Current in High-Performance Mode
- TX: 46 mA at +14 dBm
- Other:
- Data FIFOs: Separate 128-Byte RX and TX
- Support for Seamless Integration With the CC1190 Device for Increased Range Providing up to 3-dB Improvement in RX Sensitivity and up to +27 dBm TX Output Power
- Digital
Features:
- WaveMatch: Advanced Digital Signal Processing for Improved Sync Detect Performance
- Autonomous Image Removal
- Security: Hardware AES128 Accelerator
- Data FIFOs: Separate 128-Byte RX and TX
- Includes Functions for Antenna Diversity Support
- Support for Retransmission
- Support for Auto-Acknowledge of Received Packets
- Automatic Clear Channel Assessment (CCA) for Listen-Before-Talk (LBT) Systems
- Built-in Coding Gain Support for Increased Range and Robustness
- Digital RSSI Measurement
- Improved OOK Shaping for Less Occupied Bandwidth, Enabling Higher Output Power While Meeting Regulatory Requirements
- Dedicated Packet Handling for
802.15.4g:
- CRC 16/32
- FEC, Dual Sync Detection (FEC and non-FEC Packets)
- Whitening
- General:
- RoHS-Compliant 5-mm × 5-mm No-Lead QFN 32-Pin Package (RHB)
- Pin-Compatible With the CC1120 Device
- Regulations – Suitable for Systems Targeting
Compliance With:
- Europe: ETSI EN 300 220
- US: FCC CFR47 Part 15
- Japan: ARIB STD-T108
The CC1201 device is a fully integrated single-chip radio transceiver designed for high performance at very low-power and low-voltage operation in cost-effective wireless systems. All filters are integrated, thus removing the need for costly external SAW and IF filters. The device is mainly intended for the ISM (Industrial, Scientific, and Medical) and SRD (Short Range Device) frequency bands at 164–190 MHz, 410–475 MHz, and 820–950 MHz.
The CC1201 device provides extensive hardware support for packet handling, data buffering, burst transmissions, clear channel assessment, link quality indication, and Wake-On-Radio. The main operating parameters of the CC1201 device can be controlled through an SPI interface. In a typical system, the CC1201 device will be used with a microcontroller and only few external passive components.
The CC1201 offers the same performance as the CC1200 for channel filter bandwidths of 50 kHz or more, and therefore presents a lower cost option for applications that do not require narrowband support.
您可能會感興趣的類似產品
功能相似於所比較的產品。
技術文件
設計與開發
如需其他條款或必要資源，請按一下下方的任何標題以檢視詳細頁面 (如有)。
SMARTRFTRXEBK — SmartRF 收發器評估板
SmartRF 收發器評估板 (TrxEB) 與德州儀器的低功耗 RF 收發器搭配使用，以進行評估、性能測試和軟體開發。
支援下列收發器評估模組：
- CC1101EM*
- CC11xLEM*
- CC112xEM*
- CC1175EM*
- CC1200EM*
- CC2500EM
- CC2520EM
(*) 所有頻率變體和 CC1190 的組合也受支援
評估模組可以在 TI Store 以 EMK（評估模組套件）形式單獨購買。
您可以利用 SmartRF TrxEB 做什麼？
- 在 MSP430F5438A MCU 上開發您的無線電通訊協定。請參閱相關收發器網頁上的程式碼範例。
- 使用 SmartRF Studio 評估收發器的性能。
- 將 (...)
CC1200DK — CC1200 開發套件
The CC1200 development kit provides a complete platform for hardware performance testing and software development for TI's sub-1 GHz CC1200 device. The development kit comes pre-programmed with a packet error rate test for easy out-of-the-box evaluation of the RF performance of the device.
RF range (...)
CC1200EMK-420-470 — CC1200 評估模組套件 420-470 MHz
The CC1200 Evaluation Module Kit for 420-470 MHz can be used in conjunction with the CC1200 Development Kit to evaluate the operation of the CC1200 in the mentioned frequency range. The CC1200DK is required for operation and needs to be ordered separately.
This CC1200 Evaluation Module Kit for (...)
CC1200EMK-868-930 — CC1200 評估模組套件 868-930 MHz
The CC1200 Evaluation Module Kit for 868-930 MHz can be used in conjunction with the CC1200 Development Kit to evaluate the operation of the CC1200 in the mentioned frequency range. The CC1200DK is required for operation and needs to be ordered separately.
SMARTRF-STUDIO-7 — SmartRF Studio
SmartRF™ Studio 是一款 Windows 應用程式，功用在於協助射頻系統的設計人員在為所有 TI CC1xxx 及 CC2xxx 低功耗射頻裝置設計過程中，能在早期階段輕鬆評估無線電。此程式簡化了配置暫存器值和命令的產生，以及射頻系統的實際測試和除錯。
SmartRF Studio 支援下列 TI 裝置：
資源
SIMPLELINK-SUB1GHZ-DESIGN-REVIEWS — SimpleLink™ CC1xxx 裝置的硬體設計審查
開始使用 SimpleLink ™ Sub-1GHz 硬體設計審審查程序：
- 步驟 1：申請審查之前，請務必檢閱技術文件與相關產品頁的設計與開發資源（請參閱下方的 CC1xxx 產品頁連結）。
- 步驟 2：下載並填寫硬體設計審查申請表。
- 步驟 3：請將填好的硬體設計審查申請表及所需文件以電子郵件傳送至：connectivity-sub1ghz-hw-review@list.ti.com
SimpleLink 硬體設計審核流程提供一對一接觸的方式，並由主題內容專家協助審查您的設計，提供您寶貴的意見。有關用於申請審核的簡單三步驟流程，以及相關技術文件和資源的連結，可在此處找到。
一般設計問題應張貼在我們的 (...)
| 封裝 | 針腳 | CAD 符號、佔位空間與 3D 模型 |
|---|---|---|
| VQFN (RHB) | 32 | Ultra Librarian |
訂購與品質
建議產品可能具有與此 TI 產品相關的參數、評估模組或參考設計。