JAJSKP5A December   2020  – September 2021 TAS2764

PRODUCTION DATA  

  1. 特長
  2. アプリケーション
  3. 概要
  4. Revision History
  5. Pin Configuration and Functions
  6. Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 I2C Timing Requirements
    7. 6.7 TDM Port Timing Requirements
    8. 6.8 Typical Characteristics
  7. Parameter Measurement Information
  8. Detailed Description
    1. 8.1  Overview
    2. 8.2  Functional Block Diagram
    3. 8.3  Feature Description
      1. 8.3.1 Device Address Selection
      2. 8.3.2 General I2C Operation
      3. 8.3.3 Register Organization
    4. 8.4  Device Functional Modes
      1. 8.4.1  TDM Port
      2. 8.4.2  Playback Signal Path
        1. 8.4.2.1  High Pass Filter
        2. 8.4.2.2  Amplifier Inversion
        3. 8.4.2.3  Digital Volume Control and Amplifier Output Level
          1. 8.4.2.3.1 Safe Mode
        4. 8.4.2.4  VBAT1S Supply
        5. 8.4.2.5  Low Voltage Signaling (LVS)
        6. 8.4.2.6  Y-Bridge
        7. 8.4.2.7  Noise Gate
        8. 8.4.2.8  Supply Tracking Limiter with Brown Out Prevention
          1. 8.4.2.8.1 Supply Tracking Limiter
          2. 8.4.2.8.2 Brownout Prevention (BOP)
        9. 8.4.2.9  Inter Chip Gain Alignment
          1. 8.4.2.9.1 Inter-Chip Communication (ICC) Pin
        10. 8.4.2.10 Class-D Settings
          1. 8.4.2.10.1 Synchronization and EMI
      3. 8.4.3  SAR ADC
      4. 8.4.4  Current and Voltage (IV) Sense
      5. 8.4.5  Post Filter Feed-Back (PFFB)
      6. 8.4.6  Load Diagnostics
      7. 8.4.7  Thermal Foldback
      8. 8.4.8  Over Power Protection
      9. 8.4.9  Clocks and PLL
      10. 8.4.10 Echo Reference
    5. 8.5  Operational Modes
      1. 8.5.1 Hardware Shutdown
      2. 8.5.2 Mode Control and Software Reset
      3. 8.5.3 Software Shutdown
      4. 8.5.4 Mute
      5. 8.5.5 Active
      6. 8.5.6 Diagnostic
      7. 8.5.7 Noise Gate
    6. 8.6  Faults and Status
      1. 8.6.1 Faults and Status over TDM
    7. 8.7  Power Sequencing Requirements
    8. 8.8  Digital Input Pull Downs
    9. 8.9  Register Map
      1. 8.9.1   Register Summary Table Page=0x00
      2. 8.9.2   Register Summary Table Page=0x01
      3. 8.9.3   Register Summary Table Page=0x04
      4. 8.9.4   PAGE (page=0x00 address=0x00) [reset=00h]
      5. 8.9.5   SW_RESET (page=0x00 address=0x01) [reset=00h]
      6. 8.9.6   MODE_CTRL (page=0x00 address=0x02) [reset=1Ah]
      7. 8.9.7   CHNL_0 (page=0x00 address=0x03) [reset=28h]
      8. 8.9.8   DC_BLK0 (page=0x00 address=0x04) [reset=21h]
      9. 8.9.9   DC_BLK1 (page=0x00 address=0x05) [reset=41h]
      10. 8.9.10  MISC_CFG1 (page=0x00 address=0x06) [reset=00h]
      11. 8.9.11  MISC_CFG2 (page=0x00 address=0x07) [reset=20h]
      12. 8.9.12  TDM_CFG0 (page=0x00 address=0x08) [reset=09h]
      13. 8.9.13  TDM_CFG1 (page=0x00 address=0x09) [reset=02h]
      14. 8.9.14  TDM_CFG2 (page=0x00 address=0x0A) [reset=0Ah]
      15. 8.9.15  LIM_MAX_ATTN (page=0x00 address=0x0B) [reset=80h]
      16. 8.9.16  TDM_CFG3 (page=0x00 address=0x0C) [reset=10h]
      17. 8.9.17  TDM_CFG4 (page=0x00 address=0x0D) [reset=13h]
      18. 8.9.18  TDM_CFG5 (page=0x00 address=0x0E) [reset=42h]
      19. 8.9.19  TDM_CFG6 (page=0x00 address=0x0F) [reset=40h]
      20. 8.9.20  TDM_CFG7 (page=0x00 address=0x10) [reset=04h]
      21. 8.9.21  TDM_CFG8 (page=0x00 address=0x11) [reset=05h]
      22. 8.9.22  TDM_CFG9 (page=0x00 address=0x12) [reset=06h]
      23. 8.9.23  TDM_CFG10 (page=0x00 address=0x13) [reset=08h]
      24. 8.9.24  TDM_CFG11 (page=0x00 address=0x14) [reset=0Ah]
      25. 8.9.25  ICC_CNFG2 (page=0x00 address=0x15) [reset=00h]
      26. 8.9.26  TDM_CFG12 (page=0x00 address=0x16) [reset=12h]
      27. 8.9.27  ICLA_CFG0 (page=0x00 address=0x17) [reset=0Ch]
      28. 8.9.28  ICLA_CFG1 (page=0x00 address=0x18) [reset=00h]
      29. 8.9.29  DG_0 (page=0x00 address=0x19) [reset=0Dh]
      30. 8.9.30  DVC (page=0x00 address=0x1A) [reset=00h]
      31. 8.9.31  LIM_CFG0 (page=0x00 address=0x1B) [reset=22h]
      32. 8.9.32  LIM_CFG1 (page=0x00 address=0x1C) [reset=32h]
      33. 8.9.33  BOP_CFG0 (page=0x00 address=0x1D) [reset=40h]
      34. 8.9.34  BOP_CFG1 (page=0x00 address=0x1E) [reset=32h]
      35. 8.9.35  BOP_CFG2 (page=0x00 address=0x1F) [reset=02h]
      36. 8.9.36  BOP_CFG3 (page=0x00 address=0x20) [reset=06h]
      37. 8.9.37  BOP_CFG4 (page=0x00 address=0x21) [reset=2Ch]
      38. 8.9.38  BOP_CFG5 (page=0x00 address=0x22) [reset=4Ch]
      39. 8.9.39  BOP_CFG6 (page=0x00 address=0x23) [reset=20h]
      40. 8.9.40  BOP_CFG7 (page=0x00 address=0x24) [reset=02h]
      41. 8.9.41  BOP_CFG8 (page=0x00 address=0x25) [reset=06h]
      42. 8.9.42  BOP_CFG9 (page=0x00 address=0x26) [reset=32h]
      43. 8.9.43  BOP_CFG10 (page=0x00 address=0x27) [reset=46h]
      44. 8.9.44  BOP_CFG11 (page=0x00 address=0x28) [reset=20h]
      45. 8.9.45  BOP_CFG12 (page=0x00 address=0x29) [reset=02h]
      46. 8.9.46  BOP_CFG13 (page=0x00 address=0x2A) [reset=06h]
      47. 8.9.47  BOP_CFG14 (page=0x00 address=0x2B) [reset=38h]
      48. 8.9.48  BOP_CFG15 (page=0x00 address=0x2C) [reset=40h]
      49. 8.9.49  BOP_CFG17 (page=0x00 address=0x2D) [reset=20h]
      50. 8.9.50  BOP_CFG18 (page=0x00 address=0x2E) [reset=02h]
      51. 8.9.51  BOP_CFG19 (page=0x00 address=0x2F) [reset=06h]
      52. 8.9.52  BOP_CFG20 (page=0x00 address=0x30) [reset=3Eh]
      53. 8.9.53  BOP_CFG21 (page=0x00 address=0x31) [reset=37h]
      54. 8.9.54  BOP_CFG22 (page=0x00 address=0x32) [reset=20h]
      55. 8.9.55  BOP_CFG23 (page=0x00 address=0x33) [reset=FFh]
      56. 8.9.56  BOP_CFG24 (page=0x00 address=0x34) [reset=E6h]
      57. 8.9.57  NG_CFG0 (page=0x00 address=0x35) [reset=BDh]
      58. 8.9.58  NG_CFG1 (page=0x00 address=0x36) [reset=ADh]
      59. 8.9.59  LVS_CFG0 (page=0x00 address=0x37) [reset=A8h]
      60. 8.9.60  DIN_PD (page=0x00 address=0x38) [reset=03h]
      61. 8.9.61  IO_DRV0 (page=0x00 address=0x39) [reset=FFh]
      62. 8.9.62  IO_DRV1 (page=0x00 address=0x3A) [reset=FFh]
      63. 8.9.63  INT_MASK0 (page=0x00 address=0x3B) [reset=FCh]
      64. 8.9.64  INT_MASK1 (page=0x00 address=0x3C) [reset=BEh]
      65. 8.9.65  INT_MASK4 (page=0x00 address=0x3D) [reset=DFh]
      66. 8.9.66  INT_MASK2 (page=0x00 address=0x40) [reset=F6h]
      67. 8.9.67  INT_MASK3 (page=0x00 address=0x41) [reset=00h]
      68. 8.9.68  INT_LIVE0 (page=0x00 address=0x42) [reset=00h]
      69. 8.9.69  INT_LIVE1 (page=0x00 address=0x43) [reset=00h]
      70. 8.9.70  INT_LIVE1_0 (page=0x00 address=0x44) [reset=00h]
      71. 8.9.71  INT_LIVE2 (page=0x00 address=0x47) [reset=00h]
      72. 8.9.72  INT_LIVE3 (page=0x00 address=0x48) [reset=00h]
      73. 8.9.73  INT_LTCH0 (page=0x00 address=0x49) [reset=00h]
      74. 8.9.74  INT_LTCH1 (page=0x00 address=0x4A) [reset=00h]
      75. 8.9.75  INT_LTCH1_0 (page=0x00 address=0x4B) [reset=00h]
      76. 8.9.76  INT_LTCH2 (page=0x00 address=0x4F) [reset=00h]
      77. 8.9.77  INT_LTCH3 (page=0x00 address=0x50) [reset=00h]
      78. 8.9.78  INT_LTCH4 (page=0x00 address=0x51) [reset=00h]
      79. 8.9.79  VBAT_MSB (page=0x00 address=0x52) [reset=00h]
      80. 8.9.80  VBAT_LSB (page=0x00 address=0x53) [reset=00h]
      81. 8.9.81  PVDD_MSB (page=0x00 address=0x54) [reset=00h]
      82. 8.9.82  PVDD_LSB (page=0x00 address=0x55) [reset=00h]
      83. 8.9.83  TEMP (page=0x00 address=0x56) [reset=00h]
      84. 8.9.84  INT_CLK_CFG (page=0x00 address=0x5C) [reset=19h]
      85. 8.9.85  MISC_CFG3 (page=0x00 address=0x5D) [reset=80h]
      86. 8.9.86  CLOCK_CFG (page=0x00 address=0x60) [reset=0Dh]
      87. 8.9.87  IDLE_IND (page=0x00 address=0x63) [reset=48]
      88. 8.9.88  MISC_CFG4 (page=0x00 address=0x65) [reset=08]
      89. 8.9.89  TG_CFG0 (page=0x00 address=0x67) [reset=00h]
      90. 8.9.90  CLK_CFG (page=0x00 address=0x68) [reset=7Fh]
      91. 8.9.91  LV_EN_CFG (page=0x00 address=0x6A) [reset=12h]
      92. 8.9.92  NG_CFG2 (page=0x00 address=0x6B) [reset=01h]
      93. 8.9.93  NG_CFG3 (page=0x00 address=0x6C) [reset=00h]
      94. 8.9.94  NG_CFG4 (page=0x00 address=0x6D) [reset=00h]
      95. 8.9.95  NG_CFG5 (page=0x00 address=0x6E) [reset=1Ah]
      96. 8.9.96  NG_CFG6 (page=0x00 address=0x6F) [reset=00h]
      97. 8.9.97  NG_CFG7 (page=0x00 address=0x70) [reset=96h]
      98. 8.9.98  PVDD_UVLO (page=0x00 address=0x71) [reset=00h]
      99. 8.9.99  DAC_MOD_RST (page=0x00 address=0x76) [reset=02h]
      100. 8.9.100 REV_ID (page=0x00 address=0x7D) [reset=30h]
      101. 8.9.101 I2C_CKSUM (page=0x00 address=0x7E) [reset=00h]
      102. 8.9.102 BOOK (page=0x00 address=0x7F) [reset=00h]
      103. 8.9.103 LSR (page=0x01 address=0x19) [reset=40h]
      104. 8.9.104 SDOUT_HIZ_1 (page=0x01 address=0x3D) [reset=00h]
      105. 8.9.105 SDOUT_HIZ_2 (page=0x01 address=0x3E) [reset=00h]
      106. 8.9.106 SDOUT_HIZ_3 (page=0x01 address=0x3F) [reset=00h]
      107. 8.9.107 SDOUT_HIZ_4 (page=0x01 address=0x40) [reset=00h]
      108. 8.9.108 SDOUT_HIZ_5 (page=0x01 address=0x41) [reset=00h]
      109. 8.9.109 SDOUT_HIZ_6 (page=0x01 address=0x42) [reset=00h]
      110. 8.9.110 SDOUT_HIZ_7 (page=0x01 address=0x43) [reset=00h]
      111. 8.9.111 SDOUT_HIZ_8 (page=0x01 address=0x44) [reset=00h]
      112. 8.9.112 SDOUT_HIZ_9 (page=0x01 address=0x45) [reset=00h]
      113. 8.9.113 TG_EN (page=0x01 address=0x47) [reset=ABh]
      114. 8.9.114 DG_DC_VAL1 (page=0x04 address=0x08) [reset=40h]
      115. 8.9.115 DG_DC_VAL2 (page=0x04 address=0x09) [reset=26h]
      116. 8.9.116 DG_DC_VAL3 (page=0x04 address=0x0A) [reset=40h]
      117. 8.9.117 DC_DG_VAL4 (page=0x04 address=0x0B) [reset=00h]
      118. 8.9.118 LIM_TH_MAX1 (page=0x04 address=0x0C) [reset=68h]
      119. 8.9.119 LIM_TH_MAX2 (page=0x04 address=0x0D) [reset=00h]
      120. 8.9.120 LIM_TH_MAX3 (page=0x04 address=0x0E) [reset=00h]
      121. 8.9.121 LIM_TH_MAX4 (page=0x04 address=0x0F) [reset=00h]
      122. 8.9.122 LIM_TH_MIN1 (page=0x04 address=0x10) [reset=28h]
      123. 8.9.123 LIM_TH_MIN2 (page=0x04 address=0x11) [reset=00h]
      124. 8.9.124 LIM_TH_MIN3 (page=0x04 address=0x12) [reset=00h]
      125. 8.9.125 LIM_TH_MIN4 (page=0x04 address=0x13) [reset=00h]
      126. 8.9.126 LIM_INF_PT1 (page=0x04 address=0x14) [reset=56h]
      127. 8.9.127 LIM_INF_PT2 (page=0x04 address=0x15) [reset=66h]
      128. 8.9.128 LIM_INF_PT3 (page=0x04 address=0x16) [reset=66h]
      129. 8.9.129 LIM_INF_PT4 (page=0x04 address=0x17) [reset=00h]
      130. 8.9.130 LIM_SLOPE1 (page=0x04 address=0x18) [reset=10h]
      131. 8.9.131 LIM_SLOPE2 (page=0x04 address=0x19) [reset=00h]
      132. 8.9.132 LIM_SLOPE3 (page=0x04 address=0x1A) [reset=00h]
      133. 8.9.133 LIM_SLOPE4 (page=0x04 address=0x1B) [reset=00h]
      134. 8.9.134 TF_HLD1 (page=0x04 address=0x1C) [reset=00h]
      135. 8.9.135 TF_HLD2 (page=0x04 address=0x1D) [reset=03h]
      136. 8.9.136 TF_HLD3 (page=0x04 address=0x1E) [reset=E8h]
      137. 8.9.137 TF_HLD4 (page=0x04 address=0x1F) [reset=00h]
      138. 8.9.138 TF_RLS1 (page=0x04 address=0x20) [reset=40h]
      139. 8.9.139 TF_RLS2 (page=0x04 address=0x21) [reset=12h]
      140. 8.9.140 TF_RLS3 (page=0x04 address=0x22) [reset=E0h]
      141. 8.9.141 TF_RLS4 (page=0x04 address=0x23) [reset=00h]
      142. 8.9.142 TF_SLOPE1 (page=0x04 address=0x24) [reset=04h]
      143. 8.9.143 TF_SLOPE2 (page=0x04 address=0x25) [reset=08h]
      144. 8.9.144 TF_SLOPE3 (page=0x04 address=0x26) [reset=89h]
      145. 8.9.145 TF_SLOPE4 (page=0x04 address=0x27) [reset=00h]
      146. 8.9.146 TF_TEMP_TH1 (page=0x04 address=0x28) [reset=39h]
      147. 8.9.147 TF_TEMP_TH2 (page=0x04 address=0x29) [reset=80h]
      148. 8.9.148 TF_TEMP_TH3 (page=0x04 address=0x2A) [reset=00h]
      149. 8.9.149 TF_TEMP_TH4 (page=0x04 address=0x2B) [reset=00h]
      150. 8.9.150 TF_MAX_ATTN1 (page=0x04 address=0x2C) [reset=2Dh]
      151. 8.9.151 TF_MAX_ATTN2 (page=0x04 address=0x2D) [reset=6Ah]
      152. 8.9.152 TF_MAX_ATTN3 (page=0x04 address=0x2E) [reset=86h]
      153. 8.9.153 TF_MAX_ATTN4 (page=0x04 address=0x2F) [reset=00h]
      154. 8.9.154 LD_CFG0 (page=0x04 address=0x40) [reset=02h]
      155. 8.9.155 LD_CFG1 (page=0x04 address=0x41) [reset=ADh]
      156. 8.9.156 LD_CFG2 (page=0x04 address=0x42) [reset=B7h]
      157. 8.9.157 LD_CFG3 (page=0x04 address=0x43) [reset=00h]
      158. 8.9.158 LD_CFG4 (page=0x04 address=0x44) [reset=00h]
      159. 8.9.159 LD_CFG5 (page=0x04 address=0x45) [reset=1Bh]
      160. 8.9.160 LD_CFG6 (page=0x04 address=0x46) [reset=6Eh]
      161. 8.9.161 LD_CFG7 (page=0x04 address=0x47) [reset=00h]
      162. 8.9.162 CLD_EFF_1 (page=0x04 address=0x48) [reset=6Ch]
      163. 8.9.163 CLD_EFF_2 (page=0x04 address=0x49) [reset=CCh]
      164. 8.9.164 CLD_EFF_3 (page=0x04 address=0x4A) [reset=CDh]
      165. 8.9.165 CLD_EFF_4 (page=0x04 address=0x4B) [reset=00h]
      166. 8.9.166 LDG_RES1 (page=0x04 address=0x4C) [reset=00h]
      167. 8.9.167 LDG_RES2 (page=0x04 address=0x4D) [reset=00h]
      168. 8.9.168 LDG_RES3 (page=0x04 address=0x4E) [reset=00h]
      169. 8.9.169 LDG_RES4 (page=0x04 address=0x4F) [reset=00h]
    10. 8.10 SDOUT Equations
  9. Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
    3. 9.3 Design Requirements
    4. 9.4 Detailed Design Procedure
      1. 9.4.1 Mono/Stereo Configuration
      2. 9.4.2 EMI Passive Devices
    5. 9.5 Application Curves
  10. 10Initialization Set Up
    1. 10.1 Recommended Configuration at Power Up
    2. 10.2 Initial Device Configuration - 4 Channel Power Up (Default Mode - PWR_MODE1)
    3. 10.3 Initial Device Configuration - 44.1 kHz
    4. 10.4 Sample Rate Change - 48 kHz to 44.1kHz
    5. 10.5 Idle Channel Hysterisis
    6. 10.6 DSP Loopback
  11. 11Power Supply and I2C Recommendations
    1. 11.1 Power Supply Modes
  12. 12Layout
    1. 12.1 Layout Guidelines
    2. 12.2 Layout Example
  13. 13Device and Documentation Support
    1. 13.1 Receiving Notification of Documentation Updates
    2. 13.2 サポート・リソース
    3. 13.3 Trademarks
    4. 13.4 Electrostatic Discharge Caution
    5. 13.5 Glossary
  14. 14Mechanical, Packaging, and Orderable Information

パッケージ・オプション

メカニカル・データ(パッケージ|ピン)
サーマルパッド・メカニカル・データ
発注情報

Device Address Selection

The TAS2764 operates using a TDM/I2S interface. Audio input and output are provided via the FSYNC, SBCLK, SDIN and SDOUT pins using formats including I2S, Left Justified and TDM. Configuration and status are provided via the SDA and SCL pins using the I2C protocol.

The table below illustrates how to configure the device for I2C address . The slave addresses are shown left shifted by one bit with the R/W bit set to 0 (i.e. {ADDR[6:0],1b0}). Resistors with tolerance better than 5% must be used for setting the address configuration.

Table 8-2 I2C Address Selection
I2C SLAVE ADDRESS 0x70 0x72 0x74 0x76 0x78 0x7A 0x7C 0x7E
ADDR PIN Short to GND 470 Ω to GND 470 Ω to AVDD 2.2k Ω to GND 2.2k Ω to AVDD 10 kΩ to GND 10 kΩ to AVDD Short to AVDD

The TAS2764 has a global 7-bit I2C address 0x80. When enabled, the device will additionally respond to I2C commands at this address regardless of the ADDR pin settings. This is used to speed up device configuration when using multiple TAS2764 devices and programming similar settings across all devices. The I2C ACK / NACK cannot be used during the multi-device writes since multiple devices are responding to the I2C command. The I2C CRC function should be used to ensure each device properly received the I2C commands. At the completion of writing multiple devices using the global address, the CRC at I2C_CKSUM register should be checked on each device using the local address for a proper value. The global I2C address can be disabled using I2C_GBL_EN register bit. The I2C address is detected by sampling the ADDR pin when SDZ pin is released. Additionally, the address may be re-detected by setting I2C_AD_DET register bit high after power up and the ADDR pin will be re-sampled.