SWRU626 December   2025 CC3501E , CC3551E

 

  1.   1
  2. 1 Read This First
    1. 1.1 About This Manual
    2. 1.2 Register, Field, and Bit Calls
    3.     Trademarks
  3. 2 Architecture Overview
    1. 2.1  Target Applications
    2. 2.2  Introduction
    3. 2.3  Internal System Diagram
    4. 2.4  Arm Cortex M33
      1. 2.4.1 Processor Core
      2. 2.4.2 SysTick Timer
      3. 2.4.3 Nested Vectored Interrupt Controller
      4. 2.4.4 System Control Block (SCB)
      5. 2.4.5 TI AI instruction extensions
    5. 2.5  Power Management
      1. 2.5.1 VDD_MAIN
      2. 2.5.2 VDD_IO
      3. 2.5.3 VDDSF
      4. 2.5.4 VDD_PA
    6. 2.6  Debug Subsystem (DEBUGSS)
    7. 2.7  Memory Subsystem (MEMSS)
      1. 2.7.1 External Memory Interface
    8. 2.8  Hardware Security Module
    9. 2.9  General Purpose Timers (GPT)
    10. 2.10 Real Time Clock (RTC)
    11. 2.11 Direct Memory Access
    12. 2.12 GPIOs
    13. 2.13 Communication Peripherals
      1. 2.13.1 UART
      2. 2.13.2 I2C
      3. 2.13.3 SPI
      4. 2.13.4 I2S
      5. 2.13.5 SDMMC
      6. 2.13.6 SDIO
      7. 2.13.7 CAN
      8. 2.13.8 ADC
  4. 3  Arm Cortex-M33 Processor
    1. 3.1 Arm Cortex-M33 Processor Introduction
    2. 3.2 Block Diagram
    3. 3.3 M33 instantiation parameters
    4. 3.4 Arm Cortex-M33 System Peripheral Details
      1. 3.4.1 Floating Point Unit (FPU)
      2. 3.4.2 Memory Protection Unit (MPU)
      3. 3.4.3 Digital Signal Processing (DSP)
      4. 3.4.4 Security Attribution Unit (SAU)
      5. 3.4.5 System Timer
      6. 3.4.6 Nested Vectored Interrupt Controller
      7. 3.4.7 System Control Block
      8. 3.4.8 System Control Space
    5. 3.5 CPU Sub-System Peripheral Details
      1. 3.5.1 Trace Port Interface Unit (TPIU)
      2. 3.5.2 DAP Bridge and Debug Authentication
      3. 3.5.3 Implementation Defined Attribution Unit (IDAU)
    6. 3.6 Programming Model
      1. 3.6.1 Modes of operation and execution
        1. 3.6.1.1 Security states
        2. 3.6.1.2 Operating modes
        3. 3.6.1.3 Operating states
        4. 3.6.1.4 Privileged access and unprivileged user access
      2. 3.6.2 Instruction set summary
      3. 3.6.3 Memory model
        1. 3.6.3.1 Private Peripheral Bus
        2. 3.6.3.2 Unaligned accesses
      4. 3.6.4 Processor core registers summary
      5. 3.6.5 Exceptions
        1. 3.6.5.1 Exception handling and prioritization
    7. 3.7 TrustZone-M
      1. 3.7.1 Overview
      2. 3.7.2 M33 Configuration
      3. 3.7.3 Description of elements
        1. 3.7.3.1 IDAU (Implementation Defined Attribution Unit)
          1. 3.7.3.1.1 Expected use
    8. 3.8 CC35xx Host MCU Registers
      1. 3.8.1 HOSTMCU_AON Registers
      2. 3.8.2 HOST_MCU Registers
      3. 3.8.3 HOST_MCU_SEC Registers
    9. 3.9 Arm® Cortex®-M33 Registers
      1. 3.9.1  CPU_ROM_TABLE Registers
      2. 3.9.2  TPIU Registers
      3. 3.9.3  DCB Registers
      4. 3.9.4  DIB Registers
      5. 3.9.5  DWT Registers
      6. 3.9.6  FPB Registers
      7. 3.9.7  FPE Registers
      8. 3.9.8  ICB Registers
      9. 3.9.9  ITM Registers
      10. 3.9.10 MPU Registers
      11. 3.9.11 NVIC Registers
      12. 3.9.12 SAU Registers
      13. 3.9.13 SCB Registers
      14. 3.9.14 SYSTIMER Registers
      15. 3.9.15 SYSTICK Registers
  5. 4 Memory Map
    1. 4.1 Memory Map
  6. 5 Interrupts and Events
    1. 5.1 Exception Model
      1. 5.1.1 Exception States
      2. 5.1.2 Exception Types
      3. 5.1.3 Exception Handlers
      4. 5.1.4 Vector Table
      5. 5.1.5 Exception Priorities
      6. 5.1.6 Interrupt Priority Grouping
      7. 5.1.7 Exception Entry and Return
        1. 5.1.7.1 Exception Entry
        2. 5.1.7.2 Exception Return
    2. 5.2 Fault Handling
      1. 5.2.1 Fault Types
      2. 5.2.2 Fault Escalation to HardFault
      3. 5.2.3 Fault Status Registers and Fault Address Registers
      4. 5.2.4 Lockup
    3. 5.3 Security State Switches
    4. 5.4 Event Manager
      1. 5.4.1 Introduction
      2. 5.4.2 Interrupts List
      3. 5.4.3 Wakeup Sources
      4. 5.4.4 Shared Peripherals MUX Selector
        1. 5.4.4.1 ADC HW Event Selector Mux
        2. 5.4.4.2 I2S HW Event Selector Mux
        3. 5.4.4.3 PDM HW Event Selector Mux
      5. 5.4.5 Timers MUX Selector Mux
        1. 5.4.5.1 SysTimer0 HW Event Selector Mux
        2. 5.4.5.2 SysTimer1 HW Event Selector Mux
        3. 5.4.5.3 RTC HW Event Selector Mux
      6. 5.4.6 GPTIMERs MUX Selector Mux
        1. 5.4.6.1 GPTIMER0 HW Event Selector Mux
        2. 5.4.6.2 GPTIMER1 HW Event Selector Mux
    5. 5.5 SOC_IC Registers
    6. 5.6 SOC_AON Registers
    7. 5.7 SOC_AAON Registers
  7. 6 Debug Subsystem (DEBUGSS)
    1. 6.1 Introduction
    2. 6.2 Block Diagram
    3. 6.3 Overview
    4. 6.4 Physical Interface
    5. 6.5 Debug Access Ports
    6. 6.6 Debug Features
      1. 6.6.1 Processor Debug
      2. 6.6.2 Breakpoint Unit (BPU)
      3. 6.6.3 Peripheral Debug
    7. 6.7 Behavior in Low Power Modes
    8. 6.8 Debug Access Control
    9. 6.9 SOC_DEBUGSS Registers
  8. 7 Power, Reset, Clock Management
    1. 7.1 Power Management
      1. 7.1.1 Power Supply System
        1. 7.1.1.1 VDD_MAIN
        2. 7.1.1.2 VIO
        3. 7.1.1.3 VDDSF
        4. 7.1.1.4 VPA
      2. 7.1.2 Power States
      3. 7.1.3 Power Domains
      4. 7.1.4 Brownout (BOR)
      5. 7.1.5 Boot Sequence
    2. 7.2 Reset
      1. 7.2.1 Reset Cause
      2. 7.2.2 Watchdog Timer (WDT)
    3. 7.3 Clocks
      1. 7.3.1 Fast Clock
      2. 7.3.2 Slow Clock
        1. 7.3.2.1 Slow Clock Overview
        2. 7.3.2.2 Slow Clock Tree
        3. 7.3.2.3 Slow Clock Boot Process
    4. 7.4 PRCM_AON Registers
    5. 7.5 PRCM_SCRATCHPAD Registers
  9. 8 Memory Subsystem (MEMSS)
    1. 8.1  Introduction
    2. 8.2  SRAM
    3. 8.3  D-Cache
    4. 8.4  Flash
    5. 8.5  PSRAM
    6. 8.6  XiP Memory Access
      1. 8.6.1 OTFDE
      2. 8.6.2 xSPI
      3. 8.6.3 Topology
      4. 8.6.4 µDMA
      5. 8.6.5 Arbiter
    7. 8.7  ICACHE Registers
    8. 8.8  DCACHE Registers
    9. 8.9  OSPI Registers
    10. 8.10 HOST_XIP Registers
  10. 9 Hardware Security Module (HSM)
    1. 9.1 Introduction
    2. 9.2 Overview
    3. 9.3 Mailbox and Register Access Firewall
    4. 9.4 DMA Firewall
    5. 9.5 HSM Key Storage
    6. 9.6 HSM Registers
    7. 9.7 HSM_NON_SEC Registers
    8. 9.8 HSM_SEC Registers
  11. 10Device Boot and Bootloader
    1. 10.1 CC35xx Boot Concept
    2. 10.2 Features
    3. 10.3 Vendor Images Format and Processing
      1. 10.3.1 External Flash Arrangement
      2. 10.3.2 Vendor Images Format
    4. 10.4 Boot Flows
      1. 10.4.1 Application Execution Boot Flow
      2. 10.4.2 Activation Flow
      3. 10.4.3 Initial Programming Flow
      4. 10.4.4 Reprogramming Flow
      5. 10.4.5 Wireless Connectivity Testing Tool Flow
    5. 10.5 Chain of Trust
  12. 11Direct Memory Access (DMA)
    1. 11.1 Overview
    2. 11.2 Block Diagram
    3. 11.3 Functional Description
      1. 11.3.1 Channels Assignment
      2. 11.3.2 Transfer Types
      3. 11.3.3 Addressing Modes
      4. 11.3.4 Transfer Modes
      5. 11.3.5 DMA Aligner Support
      6. 11.3.6 Initiating DMA Transfers
      7. 11.3.7 Stopping DMA Transfers
      8. 11.3.8 Channel Priorities
      9. 11.3.9 DMA Interrupts
    4. 11.4 HOST_DMA Registers
  13. 12One Time Programming (OTP)
  14. 13General Purpose Timers (GPT)
    1. 13.1 Overview
    2. 13.2 Block Diagram
    3. 13.3 Functional Description
      1. 13.3.1  Prescaler
      2. 13.3.2  Counter
      3. 13.3.3  Target
      4. 13.3.4  Channel Input Logic
      5. 13.3.5  Channel Output Logic
      6. 13.3.6  Channel Actions
        1. 13.3.6.1 Period and Pulse Width Measurement
        2. 13.3.6.2 Clear on Zero, Toggle on Compare Repeatedly
        3. 13.3.6.3 Set on Zero, Toggle on Compare Repeatedly
      7. 13.3.7  Channel Capture Configuration
      8. 13.3.8  Channel Filters
        1. 13.3.8.1 Setting up the Channel Filters
      9. 13.3.9  Synchronize Multiple GPTimers
      10. 13.3.10 Interrupts, ADC Trigger, and DMA Request
    4. 13.4 Timer Modes
      1. 13.4.1 Quadrature Decoder
      2. 13.4.2 DMA
      3. 13.4.3 IR Generation
      4. 13.4.4 Fault and Park
      5. 13.4.5 Dead-Band
      6. 13.4.6 Dead-Band, Fault and Park
      7. 13.4.7 Example Application: Brushless DC (BLDC) Motor
    5. 13.5 GPTIMER Registers
  15. 14System Timer (SysTimer)
    1. 14.1 Overview
    2. 14.2 Block Diagram
    3. 14.3 Functional Description
      1. 14.3.1 Common Channel Features
        1. 14.3.1.1 Compare Mode
        2. 14.3.1.2 Capture Mode
        3. 14.3.1.3 Additional Channel Arming Methods
      2. 14.3.2 Interrupts and Events
    4. 14.4 SYSRESOURCES Registers
    5. 14.5 SYSTIM Registers
  16. 15Real-Time Clock (RTC)
    1. 15.1 Introduction
    2. 15.2 Block Diagram
    3. 15.3 Interrupts and Events
      1. 15.3.1 Input Event
      2. 15.3.2 Output Event
      3. 15.3.3 Arming and Disarming Channels
    4. 15.4 CAPTURE and COMPARE Configurations
      1. 15.4.1 CHANNEL 0 - COMPARE CHANNEL
      2. 15.4.2 CHANNEL 1 - CAPTURE CHANNEL
    5. 15.5 RTC Registers
  17. 16General Purpose Input/Output (GPIOs)
    1. 16.1 Introduction
    2. 16.2 Block Diagram
    3. 16.3 I/O Mapping and Configuration
      1. 16.3.1 Basic I/O Mapping
      2. 16.3.2 Pin Mapping
    4. 16.4 Edge Detection
    5. 16.5 GPIO
    6. 16.6 I/O Pins
    7. 16.7 Unused Pins
    8. 16.8 IOMUX Registers
  18. 17Universal Asynchronous Receivers/Transmitters (UART)
    1. 17.1 Introduction
    2. 17.2 Block Diagram
    3. 17.3 UART Functional Description
      1. 17.3.1 Transmit and Receive Logic
      2. 17.3.2 Baud Rate Generation
      3. 17.3.3 FIFO Operation
        1. 17.3.3.1 FIFO Remapping
      4. 17.3.4 Data Transmission
      5. 17.3.5 Flow Control
      6. 17.3.6 IrDA Encoding and Decoding
      7. 17.3.7 Interrupts
      8. 17.3.8 Loopback Operation
    4. 17.4 UART-LIN Specification
      1. 17.4.1 Break transmission in UART mode
      2. 17.4.2 Break reception in UART mode
      3. 17.4.3 Break/Synch transmission in LIN mode
      4. 17.4.4 Break/Synch reception in LIN mode
      5. 17.4.5 Dormant mode operation
      6. 17.4.6 Event signal generation
      7. 17.4.7 Event signal detection when device is in active/idle modes
      8. 17.4.8 Event signal detection when device is in sleep mode
    5. 17.5 Interface to Host DMA
    6. 17.6 Initialization and Configuration
    7. 17.7 UART Registers
  19. 18Serial Peripheral Interface (SPI)
    1. 18.1 Overview
      1. 18.1.1 Features
      2. 18.1.2 Block Diagram
    2. 18.2 Signal Description
    3. 18.3 Functional Description
      1. 18.3.1  Clock Control
      2. 18.3.2  FIFO Operation
        1. 18.3.2.1 Transmit FIFO
        2. 18.3.2.2 Repeated Transmit Operation
        3. 18.3.2.3 Receive FIFO
        4. 18.3.2.4 FIFO Flush
      3. 18.3.3  Interrupts
      4. 18.3.4  Data Format
      5. 18.3.5  Delayed Data Sampling
      6. 18.3.6  Chip Select Control
      7. 18.3.7  Command Data Control
      8. 18.3.8  Protocol Descriptions
        1. 18.3.8.1 Motorola SPI Frame Format
        2. 18.3.8.2 Texas Instruments Synchronous Serial Frame Format
        3. 18.3.8.3 MICROWIRE Frame Format
      9. 18.3.9  CRC Configuration
      10. 18.3.10 Auto CRC Functionality
      11. 18.3.11 SPI Status
      12. 18.3.12 Debug Halt
    4. 18.4 Host DMA Operation
    5. 18.5 Initialization and Configuration
    6. 18.6 SPI Registers
  20. 19Inter-Integrated Circuit (I2C) Interface
    1. 19.1 Introduction
    2. 19.2 Block Diagram
    3. 19.3 Functional Description
      1. 19.3.1 Clock Control
        1. 19.3.1.1 Internal Clock
        2. 19.3.1.2 External Clock
      2. 19.3.2 General Architecture
        1. 19.3.2.1  Start and Stop Conditions
        2. 19.3.2.2  Data Format with 7-Bit Address
        3. 19.3.2.3  Data Format with 10-Bit Addressing
          1. 19.3.2.3.1 Additional 10-Bit Scenarios
        4. 19.3.2.4  Acknowledge
        5. 19.3.2.5  Repeated Start
        6. 19.3.2.6  Clock Stretching
        7. 19.3.2.7  Arbitration
        8. 19.3.2.8  Multi-Controller mode
        9. 19.3.2.9  Glitch Suppression
        10. 19.3.2.10 FIFO Operation
        11. 19.3.2.11 Burst Mode Operation
        12. 19.3.2.12 DMA Operation
        13. 19.3.2.13 Flush Stale Tx Data in Target Mode
          1. 19.3.2.13.1 Recommended Sequence
        14. 19.3.2.14 SMBUS 3.0 Support
          1. 19.3.2.14.1 Quick Command
          2. 19.3.2.14.2 Acknowledge Control
          3. 19.3.2.14.3 Alert Response protocol
          4. 19.3.2.14.4 Address Resolution Protocol
          5. 19.3.2.14.5 Enhanced Acknowledge Control
    4. 19.4 Initialization and Configuration
    5. 19.5 Interrupts
    6. 19.6 I2C Registers
  21. 20Secure Digital Multimedia Card (SDMMC)
    1. 20.1 Introduction
      1. 20.1.1 SDMMC Features
      2. 20.1.2 Integration
    2. 20.2 Functional Description
      1. 20.2.1  SDMMC Functional Modes
        1. 20.2.1.1 SDMMC Connected to an SD Card
        2. 20.2.1.2 Protocol and Data Format
          1. 20.2.1.2.1 Protocol
          2. 20.2.1.2.2 Data Format
      2. 20.2.2  SD Card Feedback
      3. 20.2.3  Resets
        1. 20.2.3.1 Hardware Reset
        2. 20.2.3.2 Software Reset
      4. 20.2.4  Interrupt Requests
        1. 20.2.4.1 Interrupt-Driven Operation
        2. 20.2.4.2 Polling
      5. 20.2.5  DMA Modes
        1. 20.2.5.1 DMA Peripheral Mode Operations
          1. 20.2.5.1.1 DMA Receive Mode
          2. 20.2.5.1.2 DMA Transmit Mode
      6. 20.2.6  Buffer Management
        1. 20.2.6.1 Data Buffer
          1. 20.2.6.1.1 Memory Size and Block Length
          2. 20.2.6.1.2 Data Buffer Status
      7. 20.2.7  Transfer Process
        1. 20.2.7.1 Different Types of Commands
        2. 20.2.7.2 Different Types of Responses
      8. 20.2.8  Transfer or Command Status and Error Reporting
        1. 20.2.8.1 Busy Timeout for R1b, R5b Response Type
        2. 20.2.8.2 Busy Timeout After Write CRC Status
        3. 20.2.8.3 Write CRC Status Timeout
        4. 20.2.8.4 Read Data Timeout
      9. 20.2.9  Auto Command 12 Timings
        1. 20.2.9.1 Auto Command 12 Timings During Write Transfer
        2. 20.2.9.2 Auto Command 12 Timings During Read Transfer
      10. 20.2.10 Transfer Stop
      11. 20.2.11 Output Signals Generation
        1. 20.2.11.1 Generation on Falling Edge of SDMMC Clock
        2. 20.2.11.2 Generation on Rising Edge of SDMMC Clock
      12. 20.2.12 Test Registers
      13. 20.2.13 SDMMC Hardware Status Features
    3. 20.3 Low-Level Programming Models
      1. 20.3.1 SDMMC Initialization Flow
        1. 20.3.1.1 Enable OCP and CLKADPI Clocks
        2. 20.3.1.2 SD Soft Reset Flow
        3. 20.3.1.3 Set SD Default Capabilities
        4. 20.3.1.4 SDMMC Host and Bus Configuration
      2. 20.3.2 Operational Modes Configuration
        1. 20.3.2.1 Basic Operations for SDMMC
        2. 20.3.2.2 Card Detection, Identification, and Selection
    4. 20.4 SDMMC Registers
  22. 21Secure Digital Input/Output (SDIO)
    1. 21.1 Introduction
    2. 21.2 Block Diagram
    3. 21.3 Functional Description
      1. 21.3.1 SDIO Interface Description
      2. 21.3.2 Protocol and Data Format
      3. 21.3.3 I/O Read/Write Command
        1. 21.3.3.1 IO_WR_DIRECT Command (CMD52)
        2. 21.3.3.2 IO_WR_EXTENDED Command (CMD53)
      4. 21.3.4 Reset
      5. 21.3.5 FIFO Operation
        1. 21.3.5.1 Rx FIFO (For Host Write)
        2. 21.3.5.2 Tx FIFO (For Host Read)
      6. 21.3.6 Interrupt Request
        1. 21.3.6.1 External Host IRQ
        2. 21.3.6.2 M33 IRQ
      7. 21.3.7 Transaction Details
        1. 21.3.7.1 Host write to SDIO IP (Rx FIFO)
          1. 21.3.7.1.1 Host write to SDIO IP (Rx FIFO) – Long SW latency case
          2. 21.3.7.1.2 Host write to SDIO IP (Rx FIFO) – CRC Error Case
        2. 21.3.7.2 Host reads from SDIO (TX buffer)
    4. 21.4 SDIO_CORE Registers
    5. 21.5 SDIO_CARD_FN1 Registers
  23. 22Inter-Integrated Circuit Sound (I2S)
    1. 22.1  Introduction
    2. 22.2  Block Diagram
    3. 22.3  Signal Descriptions
    4. 22.4  Functional Description
      1. 22.4.1 Pin Configuration
      2. 22.4.2 Serial Format Configuration
        1. 22.4.2.1 Register Configuration
      3. 22.4.3 Left-Justified (LJF)
        1. 22.4.3.1 Register Configuration
      4. 22.4.4 Right-Justified (RJF)
        1. 22.4.4.1 Register Configuration
      5. 22.4.5 DSP
        1. 22.4.5.1 Register Configuration
      6. 22.4.6 Clock Configuration
    5. 22.5  Memory Interface
      1. 22.5.1 Sample Word Length
      2. 22.5.2 Padding Mechanism
      3. 22.5.3 Channel Mapping
      4. 22.5.4 Sample Storage in Memory
      5. 22.5.5 DMA Operation
        1. 22.5.5.1 Start-Up
        2. 22.5.5.2 Operation
        3. 22.5.5.3 Shutdown
    6. 22.6  Samplestamp Generator
      1. 22.6.1 Samplestamp Counters
      2. 22.6.2 Start-Up Triggers
      3. 22.6.3 Samplestamp Capture
      4. 22.6.4 Achieving constant audio latency
    7. 22.7  Error Detection
    8. 22.8  Usage
      1. 22.8.1 Start-Up Sequence
      2. 22.8.2 Shutdown Sequence
    9. 22.9  I2S Configuration Guideline
    10. 22.10 I2S Registers
  24. 23Pulse Density Modulation (PDM)
    1. 23.1  Introduction
    2. 23.2  Block Diagram
    3. 23.3  Input Selection
      1. 23.3.1 PDM Data Mode
      2. 23.3.2 Manchester Input Mode
    4. 23.4  CIC Filter
      1. 23.4.1 Filter Design
      2. 23.4.2 Digital Filter Output
      3. 23.4.3 Offset Binary Mode
      4. 23.4.4 Twos-Complement Mode
    5. 23.5  FIFO Organization in Different Modes
      1. 23.5.1 Single Mono Microphone Configuration
        1. 23.5.1.1 24-bit Sample Size
          1. 23.5.1.1.1 32-bit Data Read
        2. 23.5.1.2 16-bit Sample Size
          1. 23.5.1.2.1 32-bit Data Read
          2. 23.5.1.2.2 16-bit Data Read
        3. 23.5.1.3 8-bit Sample Size
          1. 23.5.1.3.1 32-bit Data Read
          2. 23.5.1.3.2 16-bit Data Read
          3. 23.5.1.3.3 8-bit Data Read
      2. 23.5.2 Stereo or Dual Mono Microphone Configuration
        1. 23.5.2.1 24-bit Sample Size
          1. 23.5.2.1.1 32-bit Data Read
        2. 23.5.2.2 16-bit Sample Size
          1. 23.5.2.2.1 32-bit Data Read
          2. 23.5.2.2.2 16-bit Data Read
        3. 23.5.2.3 8-bit Sample Size
          1. 23.5.2.3.1 32-bit Data Read
          2. 23.5.2.3.2 16-bit Data Read
          3. 23.5.2.3.3 8-bit Data Read
      3. 23.5.3 FIFO Threshold Setting
      4. 23.5.4 Reset FIFO
    6. 23.6  Automatic Gain Control (AGC)
      1. 23.6.1 Operation in 2's Complement Format
      2. 23.6.2 Operation in Offset Binary Format
    7. 23.7  Interrupts
    8. 23.8  Clock Select and Control
    9. 23.9  DMA Operation
    10. 23.10 Samplestamp Generator
      1. 23.10.1 Samplestamp Counters
      2. 23.10.2 Start-Up Triggers
      3. 23.10.3 Samplestamp Capture
      4. 23.10.4 Achieving Constant Audio Latency
    11. 23.11 Debug‑Mode Flag Behavior
    12. 23.12 Software Guidelines
    13. 23.13 PDM Registers
  25. 24Analog to Digital Converter (ADC)
    1. 24.1 Overview
    2. 24.2 Block Diagram
    3. 24.3 Functional Description
      1. 24.3.1  ADC Core
      2. 24.3.2  Voltage Reference Options
      3. 24.3.3  Internal Channels
      4. 24.3.4  Resolution Modes
      5. 24.3.5  ADC Clocking
      6. 24.3.6  Power Down Behavior
      7. 24.3.7  Sampling Trigger Sources and Sampling Modes
        1. 24.3.7.1 AUTO Sampling Mode
        2. 24.3.7.2 MANUAL Sampling Mode
      8. 24.3.8  Sampling Period
      9. 24.3.9  Conversion Modes
      10. 24.3.10 ADC Data Format
      11. 24.3.11 Status Register
      12. 24.3.12 ADC Events
        1. 24.3.12.1 Generic Event Publishers (INT_EVENT0 & INT_EVENT1)
        2. 24.3.12.2 DMA Trigger Event Publisher (INT_EVENT2)
        3. 24.3.12.3 Generic Event Subscriber
      13. 24.3.13 Advanced Features
        1. 24.3.13.1 Window Comparator
        2. 24.3.13.2 DMA & FIFO Operation
          1. 24.3.13.2.1 DMA/CPU Operation in Non-FIFO Mode (FIFOEN=0)
          2. 24.3.13.2.2 DMA/CPU Operation in FIFO Mode (FIFOEN=1)
          3. 24.3.13.2.3 DMA/CPU Operation Summary Matrix
        3. 24.3.13.3 Ad-hoc Single Conversion
    4. 24.4 ADC Registers
  26. 25Controller Area Network (CAN)
    1. 25.1 Introduction
    2. 25.2 Functions
    3. 25.3 DCAN Subsystem
    4. 25.4 DCAN Functional Description
      1. 25.4.1 Operating Modes
        1. 25.4.1.1 Software Initialization
        2. 25.4.1.2 Normal Operation
        3. 25.4.1.3 Restricted Operation Mode
        4. 25.4.1.4 Bus Monitoring Mode
        5. 25.4.1.5 Disabled Automatic Retransmission
          1. 25.4.1.5.1 Frame Transmission in DAR Mode
        6. 25.4.1.6 Power Down (Sleep Mode)
          1. 25.4.1.6.1 DCAN clock stop and wake operations
          2. 25.4.1.6.2 DCAN debug suspend operation
        7. 25.4.1.7 Test Modes
          1. 25.4.1.7.1 External Loop Back Mode
          2. 25.4.1.7.2 Internal Loop Back Mode
      2. 25.4.2 Timestamp Generation
        1. 25.4.2.1 Block Diagram
      3. 25.4.3 Timeout Counter
      4. 25.4.4 Rx Handling
        1. 25.4.4.1 Acceptance Filtering
          1. 25.4.4.1.1 Range Filter
          2. 25.4.4.1.2 Filter for specific IDs
          3. 25.4.4.1.3 Classic Bit Mask Filter
          4. 25.4.4.1.4 Standard Message ID Filtering
          5. 25.4.4.1.5 Extended Message ID Filtering
        2. 25.4.4.2 Rx FIFOs
          1. 25.4.4.2.1 Rx FIFO Blocking Mode
          2. 25.4.4.2.2 Rx FIFO Overwrite Mode
        3. 25.4.4.3 Dedicated Rx Buffers
          1. 25.4.4.3.1 Rx Buffer Handling
        4. 25.4.4.4 Debug on CAN Support
          1. 25.4.4.4.1 Filtering for Debug Messages
          2. 25.4.4.4.2 Debug Message Handling
      5. 25.4.5 Tx Handling
        1. 25.4.5.1 Transmit Pause
        2. 25.4.5.2 Dedicated Tx Buffers
        3. 25.4.5.3 Tx FIFO
        4. 25.4.5.4 Tx Queue
        5. 25.4.5.5 Mixed Dedicated Tx Buffers / Tx FIFO
        6. 25.4.5.6 Mixed Dedicated Tx Buffers / Tx Queue
        7. 25.4.5.7 Transmit Cancellation
        8. 25.4.5.8 Tx Event Handling
      6. 25.4.6 FIFO Acknowledge Handling
      7. 25.4.7 DCAN Message RAM
        1. 25.4.7.1 Message RAM Configuration
        2. 25.4.7.2 Rx Buffer and FIFO Element
        3. 25.4.7.3 Tx Buffer Element
        4. 25.4.7.4 Tx Event FIFO Element
        5. 25.4.7.5 Standard Message ID Filter Element
        6. 25.4.7.6 Extended Message ID Filter Element
      8. 25.4.8 Interrupt Requests
    5. 25.5 DCAN Wrapper
    6. 25.6 DCAN Clock Enable
    7. 25.7 DCAN Registers
  27. 26Revision History

5.7 SOC_AAON Registers

Table 5-202 lists the memory-mapped registers for the SOC_AAON registers. All register offset addresses not listed in Table 5-202 should be considered as reserved locations and the register contents should not be modified.

Table 5-202 SOC_AAON Registers
OffsetAcronymRegister NameSection
0hDMASIMASKSecure Interrupt MaskSection 5.7.1
4hDMASISETSecure Interrupt SetSection 5.7.2
8hDMASICLRSecure Interrupt ClearSection 5.7.3
ChDMASIMSETInterrupt Mask SetSection 5.7.4
10hDMASIMCLRInterrupt Mask ClearSection 5.7.5
14hDMASRISSecure Event StatusSection 5.7.6
18hDMASMISMasked Interrupt StatusSection 5.7.7
1000hDMANSIMASKDMA Non-Secure Interrupt MaskSection 5.7.8
1004hDMANSISETDMA Non-Secure Interrupt SetSection 5.7.9
1008hDMANSICLRDMA Non-Secure Interrupt Clear RegisterSection 5.7.10
100ChDMANSIMSETDMA Non-Secure Interrupt Mask SetSection 5.7.11
1010hDMANSIMCLRDMA Interrupt Mask ClearSection 5.7.12
1014hDMANSRISDMA Non -Secure Raw interrupt StatusSection 5.7.13
1018hDMANSMISDMA Non-Secure Mask Interrupt StatusSection 5.7.14

Complex bit access types are encoded to fit into small table cells. Table 5-203 shows the codes that are used for access types in this section.

Table 5-203 SOC_AAON Access Type Codes
Access TypeCodeDescription
Read Type
RRRead
Write Type
WWWrite
Reset or Default Value
-nValue after reset or the default value

5.7.1 DMASIMASK Register (Offset = 0h) [Reset = 00000000h]

DMASIMASK is shown in Table 5-204.

Return to the Summary Table.

DMA M33 Secure Event IMASK. Mask Event. '0' - CLR - Clear Interrupt Mask '1' - SET - Set Interrupt Mask

Table 5-204 DMASIMASK Register Field Descriptions
BitFieldTypeResetDescription
31-12RESERVEDR0hReserved
11-0IMASKR/W0h'0' - CLR - Clear Interrupt Mask '1' - SET - Set Interrupt Mask

5.7.2 DMASISET Register (Offset = 4h) [Reset = 00000000h]

DMASISET is shown in Table 5-205.

Return to the Summary Table.

DMA M33 Secure Event ISET. Sets event in RIS Write 0 - NO_EFFECT - Writing 0 has no effect Write 1 - SET - Sets interrupt

Table 5-205 DMASISET Register Field Descriptions
BitFieldTypeResetDescription
31-12RESERVEDR0hReserved
11-0ISETW0hWrite 0 - NO_EFFECT - Writing 0 has no effect Write 1 - SET - Sets interrupt Type: Write-Clear.

5.7.3 DMASICLR Register (Offset = 8h) [Reset = 00000000h]

DMASICLR is shown in Table 5-206.

Return to the Summary Table.

DMA M33 Secure Event ICLR. Clears event in RIS Write 0 - NO_EFFECT - Writing 0 has no effect Write 1 - CLR - Clears the Event

Table 5-206 DMASICLR Register Field Descriptions
BitFieldTypeResetDescription
31-12RESERVEDR0hReserved
11-0ICLRW0hWrite 0 - NO_EFFECT - Writing 0 has no effect Write 1 - CLR - Clears the Event Type: Write-Clear.

5.7.4 DMASIMSET Register (Offset = Ch) [Reset = 00000000h]

DMASIMSET is shown in Table 5-207.

Return to the Summary Table.

DMA M33 Secure Event IMSET. Sets Event Write 0 - NO_EFFECT - Writing 0 has no effect Write 1 - SET - Set interrupt mask

Table 5-207 DMASIMSET Register Field Descriptions
BitFieldTypeResetDescription
31-12RESERVEDR0hReserved
11-0IMSETW0hWrite 0 - NO_EFFECT - Writing 0 has no effect Write 1 - SET - Set interrupt mask Type: Write-Clear

5.7.5 DMASIMCLR Register (Offset = 10h) [Reset = 00000000h]

DMASIMCLR is shown in Table 5-208.

Return to the Summary Table.

DMA M33 Secure Event IMCLR. Clears Event Write 0 - NO_EFFECT - Writing 0 has no effect Write 1 - CLR - Clear interrupt mask

Table 5-208 DMASIMCLR Register Field Descriptions
BitFieldTypeResetDescription
31-12RESERVEDR0hReserved
11-0IMCLRW0hWrite 0 - NO_EFFECT - Writing 0 has no effect Write 1 - CLR - Clear interrupt mask Type: Write-Clear.

5.7.6 DMASRIS Register (Offset = 14h) [Reset = 00000000h]

DMASRIS is shown in Table 5-209.

Return to the Summary Table.

DMA M33 Secure Event RIS. Raw interrupt status for event. This bit is set to 1 when an event is received. when the corresponding bit in ICLR is set to 1, this bit will be cleared. Read 0 - CLR - Interrupt did not occur Read 1 - SET - Interrupt occurred

Table 5-209 DMASRIS Register Field Descriptions
BitFieldTypeResetDescription
31-12RESERVEDR0hReserved
11-0RISR0hRead 0 - CLR - Interrupt did not occur Read 1 - SET - Interrupt occurred

5.7.7 DMASMIS Register (Offset = 18h) [Reset = 00000000h]

DMASMIS is shown in Table 5-210.

Return to the Summary Table.

DMA M33 Secure Event MIS. Mask interrupt status for event Read 0 - CLR - Interrupt did not occur Read 1 - SET - Interrupt occurred

Table 5-210 DMASMIS Register Field Descriptions
BitFieldTypeResetDescription
31-12RESERVEDR0hReserved
11-0MISR0hRead 0 - CLR - Interrupt did not occur Read 1 - SET - Interrupt occurred

5.7.8 DMANSIMASK Register (Offset = 1000h) [Reset = 00000000h]

DMANSIMASK is shown in Table 5-211.

Return to the Summary Table.

DMA M33 Non-Secured IMASK. Mask Event. '0' - CLR - Clear Interrupt Mask '1' - SET - Set Interrupt Mask

Table 5-211 DMANSIMASK Register Field Descriptions
BitFieldTypeResetDescription
31-12RESERVEDR0hReserved
11-0IMASKR/W0h'0' - CLR - Clear Interrupt Mask '1' - SET - Set Interrupt Mask

5.7.9 DMANSISET Register (Offset = 1004h) [Reset = 00000000h]

DMANSISET is shown in Table 5-212.

Return to the Summary Table.

DMA M33 Non-Secured ISET. Sets event in RIS Write 0 - NO_EFFECT - Writing 0 has no effect Write 1 - SET - Sets interrupt

Table 5-212 DMANSISET Register Field Descriptions
BitFieldTypeResetDescription
31-12RESERVEDR0hReserved
11-0ISETW0hWrite 0 - NO_EFFECT - Writing 0 has no effect Write 1 - SET - Sets interrupt Type: Write-Clear.

5.7.10 DMANSICLR Register (Offset = 1008h) [Reset = 00000000h]

DMANSICLR is shown in Table 5-213.

Return to the Summary Table.

DMA M33 Non-Secured ICLR. Clears event in RIS Write 0 - NO_EFFECT - Writing 0 has no effect Write 1 - CLR - Clears the Event

Table 5-213 DMANSICLR Register Field Descriptions
BitFieldTypeResetDescription
31-12RESERVEDR0hReserved
11-0ICLRW0hWrite 0 - NO_EFFECT - Writing 0 has no effect Write 1 - CLR - Clears the Event Type: Write-Clear.

5.7.11 DMANSIMSET Register (Offset = 100Ch) [Reset = 00000000h]

DMANSIMSET is shown in Table 5-214.

Return to the Summary Table.

DMA M33 Non-Secured IMSET. Sets Event Write 0 - NO_EFFECT - Writing 0 has no effect Write 1 - SET - Set interrupt mask

Table 5-214 DMANSIMSET Register Field Descriptions
BitFieldTypeResetDescription
31-12RESERVEDR0hReserved
11-0IMSETW0hWrite 0 - NO_EFFECT - Writing 0 has no effect Write 1 - SET - Set interrupt mask Type: Write-Clear

5.7.12 DMANSIMCLR Register (Offset = 1010h) [Reset = 00000000h]

DMANSIMCLR is shown in Table 5-215.

Return to the Summary Table.

DMA M33 Non-Secured IMCLR. Clears Event Write 0 - NO_EFFECT - Writing 0 has no effect Write 1 - CLR - Clear interrupt mask

Table 5-215 DMANSIMCLR Register Field Descriptions
BitFieldTypeResetDescription
31-12RESERVEDR0hReserved
11-0IMCLRW0hWrite 0 - NO_EFFECT - Writing 0 has no effect Write 1 - CLR - Clear interrupt mask Type: Write-Clear.

5.7.13 DMANSRIS Register (Offset = 1014h) [Reset = 00000000h]

DMANSRIS is shown in Table 5-216.

Return to the Summary Table.

DMA M33 Non-Secured RIS. Raw interrupt status for event. This bit is set to 1 when an event is received. when the corresponding bit in ICLR is set to 1, this bit will be cleared. Read 0 - CLR - Interrupt did not occur Read 1 - SET - Interrupt occurred

Table 5-216 DMANSRIS Register Field Descriptions
BitFieldTypeResetDescription
31-12RESERVEDR0hReserved
11-0RISR0hRead 0 - CLR - Interrupt did not occur Read 1 - SET - Interrupt occurred

5.7.14 DMANSMIS Register (Offset = 1018h) [Reset = 00000000h]

DMANSMIS is shown in Table 5-217.

Return to the Summary Table.

DMA M33 Non-Secured MIS. Mask interrupt status for event Read 0 - CLR - Interrupt did not occur Read 1 - SET - Interrupt occurred

Table 5-217 DMANSMIS Register Field Descriptions
BitFieldTypeResetDescription
31-12RESERVEDR0hReserved
11-0MISR0hRead 0 - CLR - Interrupt did not occur Read 1 - SET - Interrupt occurred