SBASAO8 June   2025 DAC39RF20

ADVANCE INFORMATION  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Device Comparison
  6. 5 Pin Configuration and Functions
  7. 6 Specifications
    1. 6.1  Absolute Maximum Ratings
    2. 6.2  ESD Ratings
    3. 6.3  Recommended Operating Conditions
    4. 6.4  Thermal Information
    5. 6.5  Electrical Characteristics - DC Specifications
    6. 6.6  Electrical Characteristics - AC Specifications
    7. 6.7  Electrical Characteristics - Power Consumption
    8. 6.8  Timing Requirements
    9. 6.9  Switching Characteristics
    10. 6.10 SPI Interface Timing Diagrams
  8. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1  DAC Output Modes
        1. 7.3.1.1 NRZ Mode
        2. 7.3.1.2 RF Mode
        3. 7.3.1.3 DES Modes
      2. 7.3.2  DAC Core
        1. 7.3.2.1 DAC Output Structure
        2. 7.3.2.2 Full-Scale Current Adjustment
      3. 7.3.3  DEM and Dither
      4. 7.3.4  Offset Adjustment
      5. 7.3.5  Clocking Subsystem
        1. 7.3.5.1 Converter Phase Locked Loop (CPLL)
        2. 7.3.5.2 Clock and SYSREF Delay
        3. 7.3.5.3 SYSREF Capture and Monitoring
          1. 7.3.5.3.1 SYSREF Frequency Requirements
          2. 7.3.5.3.2 SYSREF Pulses for Full Alignment
          3. 7.3.5.3.3 Automatic SYSREF Calibration and Tracking
            1. 7.3.5.3.3.1 SYSREF Automatic Calibration Procedure
            2. 7.3.5.3.3.2 Multi-device Alignment
            3. 7.3.5.3.3.3 Calibration Failure
            4. 7.3.5.3.3.4 SYSREF Tracking
        4. 7.3.5.4 Trigger Clocking
      6. 7.3.6  Digital Signal Processing Blocks
        1. 7.3.6.1  Bypass Mode
        2. 7.3.6.2  DUC Mode
          1. 7.3.6.2.1 Digital Upconverter (DUC)
            1. 7.3.6.2.1.1 Interpolation Filters
            2. 7.3.6.2.1.2 Numerically Controlled Oscillator (NCO)
              1. 7.3.6.2.1.2.1 Phase-continuous NCO Update Mode
              2. 7.3.6.2.1.2.2 Phase-coherent NCO Update Mode
              3. 7.3.6.2.1.2.3 Phase-sync NCO Update Mode
              4. 7.3.6.2.1.2.4 NCO Synchronization
                1. 7.3.6.2.1.2.4.1 JESD204C LSB Synchronization
        3. 7.3.6.3  DDS SPI Mode
        4. 7.3.6.4  DDS Vector Mode
          1. 7.3.6.4.1 Second Order Amplitude Support
          2. 7.3.6.4.2 Vector Order and Symmetric Vector Mode
          3. 7.3.6.4.3 Initial Startup
          4. 7.3.6.4.4 Trigger Queuing
          5. 7.3.6.4.5 Trigger Burst
          6. 7.3.6.4.6 Hold Mode
          7. 7.3.6.4.7 Indexing Mode
          8. 7.3.6.4.8 Queued or Burst Triggers in Indexing-Mode
          9. 7.3.6.4.9 Writing Vectors While DDS is Enabled
        5. 7.3.6.5  DDS Streaming Mode
        6. 7.3.6.6  DSP Triggering
          1. 7.3.6.6.1 Trigger Latency
        7. 7.3.6.7  NCO Square Wave Mode
          1. 7.3.6.7.1 Square Wave Enable
        8. 7.3.6.8  DSP Mute Function
        9. 7.3.6.9  DSP Output Gain
        10. 7.3.6.10 Complex Output Support
        11. 7.3.6.11 Channel Bonder
        12. 7.3.6.12 Programmable FIR Filter
          1. 7.3.6.12.1 PFIR Coefficients
          2. 7.3.6.12.2 PFIR Reflection Cancellation Mode
          3. 7.3.6.12.3 PFIR Power Savings
          4. 7.3.6.12.4 PFIR Usage
        13. 7.3.6.13 DES Interpolator
          1. 7.3.6.13.1 DAC Mute Function
      7. 7.3.7  Serdes Physical Layer
        1. 7.3.7.1 Serdes PLL
          1. 7.3.7.1.1 Enabling the Serdes PLL
          2. 7.3.7.1.2 Reference Clock
          3. 7.3.7.1.3 PLL VCO Calibration
          4. 7.3.7.1.4 Serdes PLL Loop Bandwidth
        2. 7.3.7.2 Serdes Receiver
          1. 7.3.7.2.1 Serdes Data Rate Selection
          2. 7.3.7.2.2 Serdes Receiver Termination
          3. 7.3.7.2.3 Serdes Receiver Polarity
          4. 7.3.7.2.4 Serdes Clock Data Recovery
          5. 7.3.7.2.5 Serdes Equalizer
            1. 7.3.7.2.5.1 Adaptive Equalization
            2. 7.3.7.2.5.2 Fixed Equalization
            3. 7.3.7.2.5.3 Pre and Post Cursor Analysis
          6. 7.3.7.2.6 Serdes Receiver Eyescan
            1. 7.3.7.2.6.1 Eyescan Procedure
            2. 7.3.7.2.6.2 Building an Eye Diagram
        3. 7.3.7.3 Serdes PHY Status
      8. 7.3.8  JESD204C Interface
        1. 7.3.8.1 Deviation from JESD204C Standard
        2. 7.3.8.2 Link Layer
          1. 7.3.8.2.1 Serdes Crossbar
          2. 7.3.8.2.2 Bit Error Rate Tester
          3. 7.3.8.2.3 Scrambler and Descrambler
          4. 7.3.8.2.4 64b and 66b Decoding Link Layer
            1. 7.3.8.2.4.1 Sync Header Alignment
            2. 7.3.8.2.4.2 Extended Multiblock Alignment
            3. 7.3.8.2.4.3 Data Integrity
          5. 7.3.8.2.5 8B and 10B Encoding Link Layer
            1. 7.3.8.2.5.1 Code Group Synchronization (CGS)
            2. 7.3.8.2.5.2 Initial Lane Alignment Sequence (ILAS)
            3. 7.3.8.2.5.3 Multi-frames and the Local Multiframe Clock (LMFC)
            4. 7.3.8.2.5.4 Frame and Multiframe Monitoring
            5. 7.3.8.2.5.5 Link Restart
            6. 7.3.8.2.5.6 Link Error Reports
            7. 7.3.8.2.5.7 Watchdog Timer (JTIMER)
        3. 7.3.8.3 SYSREF Alignment Required in Subclass 1 Mode
        4. 7.3.8.4 Transport Layer
        5. 7.3.8.5 JESD204C Debug Capture (JCAP)
          1. 7.3.8.5.1 Physical Layer Debug Capture
          2. 7.3.8.5.2 Link Layer Debug Capture
          3. 7.3.8.5.3 Transport Layer Debug Capture
        6. 7.3.8.6 JESD204C Interface Modes
          1. 7.3.8.6.1 JESD204C Format Diagrams
            1. 7.3.8.6.1.1 16-bit Formats
            2. 7.3.8.6.1.2 12-bit Formats
            3. 7.3.8.6.1.3 8-bit Formats
          2. 7.3.8.6.2 DUC and DDS Modes
      9. 7.3.9  Data Path Latency
      10. 7.3.10 Multi-Device Synchronization and Deterministic Latency
        1. 7.3.10.1 Programming RBD
        2. 7.3.10.2 Multiframe Lengths less than 32 Octa-Bytes (256 Bytes)
        3. 7.3.10.3 Recommended Algorithm to Determine the RBD Value
        4. 7.3.10.4 Operation in Subclass 0 Systems
      11. 7.3.11 Link Reset
      12. 7.3.12 Alarm Generation
        1. 7.3.12.1 Over Range Detection
        2. 7.3.12.2 Over Range Masking
      13. 7.3.13 Mute Function
        1. 7.3.13.1 Alarm Data Path Muting
        2. 7.3.13.2 Transmit Enables
    4. 7.4 Device Functional Modes
      1. 7.4.1 Power Modes
  9. 8 Programming
    1. 8.1 Using the Standard SPI Interface
      1. 8.1.1 SCS
      2. 8.1.2 SCLK
      3. 8.1.3 SDI
      4. 8.1.4 SDO
      5. 8.1.5 Serial Interface Protocol
      6. 8.1.6 Streaming Mode
    2. 8.2 Using the Fast Reconfiguration Interface
    3. 8.3 Register Maps
      1. 8.3.1  Standard_SPI-3.1 Registers
      2. 8.3.2  System Registers
      3. 8.3.3  Trigger Registers
      4. 8.3.4  CPLL_AND_CLOCK Registers
      5. 8.3.5  SYSREF Registers
      6. 8.3.6  JESD204C Registers
      7. 8.3.7  JESD204C_Advanced Registers
      8. 8.3.8  SerDes_Equalizer Registers
      9. 8.3.9  SerDes_Eye-Scan Registers
      10. 8.3.10 SerDes_Lane_Status Registers
      11. 8.3.11 SerDes_PLL Registers
      12. 8.3.12 DAC_and_Analog_Configuration Registers
      13. 8.3.13 Datapath Registers
      14. 8.3.14 NCO_and_Mixer Registers
      15. 8.3.15 Alarm Registers
      16. 8.3.16 Fuse_Control Registers
      17. 8.3.17 Fuse_Backed Registers
      18. 8.3.18 DDS_Vector_Mode Registers
      19. 8.3.19 Programmable_FIR Registers
  10. 9 Application and Implementation
    1. 9.1 Application Information
      1. 9.1.1 Startup Procedure
      2. 9.1.2 Bandwidth Optimization for Square Wave Mode
    2. 9.2 Typical Application: Ku-Band Radar Transmitter
      1. 9.2.1 Design Requirements
      2. 9.2.2 Detailed Design Procedure
      3. 9.2.3 Application Curves
    3. 9.3 Power Supply Recommendations
      1. 9.3.1 Power Up and Down Sequence
    4. 9.4 Layout
      1. 9.4.1 Layout Guidelines and Example
  11. 10Device and Documentation Support
    1. 10.1 Documentation Support
      1. 10.1.1 Related Documentation
    2. 10.2 Receiving Notification of Documentation Updates
    3. 10.3 Support Resources
    4. 10.4 Trademarks
    5. 10.5 Electrostatic Discharge Caution
    6. 10.6 Glossary
  12. 11Revision History
  13. 12Mechanical, Packaging, and Orderable Information

6.7 Electrical Characteristics - Power Consumption

Typical values at TA = +105°C and fast process, minimum and maximum values over operating free-air temperature range, typical supply voltages, 2 channels,external clock mode, fCLK = 22GHz, fOUT = 2997MHz, NRZ mode, IFS_SWITCH = 20mA, unless otherwise noted.
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
IVDDA18 1.8V combined supply current for VDDA18A and VDDA18B Power Mode 1: Single DAC, JMODE 0 with 1 real stream, fINPUT = 22GSPS, 1x Interpolation, fSERDES = 22.6875Gbps, 66b/64b encoding, NRZ mode, fOUT = 8797 MHz 60 mA
IVDDIO 1.8V supply current for VDDIO 1
IVDDCSR 1.8V combined supply current for VDDCLK18, VDDSYS18, VDDR18 and VDDSP18 344
IVDDCP18 1.8V supply for data converter PLL/VCO 2
IVDDL 0.8V combined supply current for VDDLB, VDDLA 340
IVDDCLK 0.8V supply current for VDDCLK08 656
IDVDD 0.8V supply current for VDDDIG, VDDT, VDDEB and VDDEA 2320
IVEE –1.8V combined supply current for VEEAM18 and VEEBM18 57
PDIS Total power dissipation 3483 mW
IVDDA18 1.8V combined supply current for VDDA18A and VDDA18B Power Mode 2: Dual DACs, JMODE 2 with 2 IQ streams, fINPUT = 5.5GSPS, 4x Interpolation, fSERDES = 22.6875Gbps, 66b/64b encoding, NRZ mode, fOUT = 2897MHz 114 mA
IVDDIO 1.8V supply current for VDDIO 0
IVDDCSR 1.8V combined supply current for VDDCLK18, VDDSYS18, VDDR18 and VDDSP18 350
IVDDCP18 1.8V supply for data converter PLL/VCO 0
IVDDL 0.8V combined supply current for VDDLB, VDDLA 710
IVDDCLK 0.8V supply current for VDDCLK08 687
IDVDD 0.8V supply current for VDDDIG, VDDT, VDDEB and VDDEA 4198
IVEE –1.8V combined supply current for VEEAM18 and VEEBM18 114
PDIS Total power dissipation 5517 mW
IVDDA18 1.8V combined supply current for VDDA18A and VDDA18B Power Mode 3: Dual DACs, JMODE 3 with 4 IQ streams, fINPUT = 2.75GSPS, 8x Interpolation, fSERDES =30.9375Gbps, 66b/64b encoding, NRZ mode, fOUT = 2897MHz, 5897MHz 114 mA
IVDDIO 1.8V supply current for VDDIO 1
IVDDCSR 1.8V combined supply current for VDDCLK18, VDDSYS18, VDDR18 and VDDSP18 388
IVDDCP18 1.8V supply for data converter PLL/VCO 0
IVDDL 0.8V combined supply current for VDDLB, VDDLA 710
IVDDCLK 0.8V supply current for VDDCLK08 687
IDVDD 0.8V supply current for VDDDIG, VDDT, VDDEB and VDDEA 5262
IVEE –1.8V combined supply current for VEEAM18 and VEEBM18 114
PDIS Total power dissipation 6437 mW
IVDDA18 1.8V combined supply current for VDDA18A and VDDA18B Power Mode 4: Dual DACs, JMODE 6 with 4 IQ streams, fINPUT = 458.3MSPS, 48x Interpolation, fSERDES =30.25Gbps, 66b/64b encoding, NRZ mode, fOUT = 2897MHz, 5897MHz 114 mA
IVDDIO 1.8V supply current for VDDIO 1
IVDDCSR 1.8V combined supply current for VDDCLK18, VDDSYS18, VDDR18 and VDDSP18 388
IVDDCP18 1.8V supply for data converter PLL/VCO 0
IVDDL 0.8V combined supply current for VDDLB, VDDLA 710
IVDDCLK 0.8V supply current for VDDCLK08 687
IDVDD 0.8V supply current for VDDDIG, VDDT, VDDEB and VDDEA 4602
IVEE –1.8V combined supply current for VEEAM18 and VEEBM18 114
PDIS Total power dissipation 5909 mW
IVDDA18 1.8V combined supply current for VDDA18A and VDDA18B Power Mode 5: Dual DACs, JMODE 17 with 2 real streams, fINPUT = 21GSPS, 1x Interpolation, fSERDES = 32.48Gbps, 66b/64b encoding, NRZ mode, fOUT = 8797MHz 114 mA
IVDDIO 1.8V supply current for VDDIO 1
IVDDCSR 1.8V combined supply current for VDDCLK18, VDDSYS18, VDDR18 and VDDSP18 395
IVDDCP18 1.8V supply for data converter PLL/VCO 0
IVDDL 0.8V combined supply current for VDDLB, VDDLA 710
IVDDCLK 0.8V supply current for VDDCLK08 687
IDVDD 0.8V supply current for VDDDIG, VDDT, VDDEB and VDDEA 3665
IVEE –1.8V combined supply current for VEEAM18 and VEEBM18 114
PDIS Total power dissipation Power Mode 5: Dual DACs, JMODE 17 with 2 real streams, fINPUT = 21GSPS, 1x Interpolation, fSERDES = 32.48Gbps, 66b/64b encoding, NRZ mode, fOUT = 8797MHz 5172 mW
PDIS Total power dissipation Power Mode 6: Power Down mW
IVDDDIG Additional Current DES enabled scales with fCLK and # DAC 150 mA
Additional Current with PFIR enabled at DUC output scales with fCLK and fraction non-zero taps (of 24) 2100 mA
IVDDCP18 Additional Current with PLLVCO enabled scales with fCLK 132 mA
IVEE Additional Current with 40mA compared to 20mA per DAC 57 mA