Top

Product details

Parameters

Number of channels (#) 4 Total supply voltage (Max) (+5V=5, +/-5V=10) 8 Total supply voltage (Min) (+5V=5, +/-5V=10) 2.7 Vos (offset voltage @ 25 C) (Max) (mV) 0.95 GBW (Typ) (MHz) 0.71 Slew rate (Typ) (V/us) 0.55 Rail-to-rail In to V-, Out Offset drift (Typ) (uV/C) 2 Iq per channel (Typ) (mA) 0.2 Vn at 1 kHz (Typ) (nV/rtHz) 12 CMRR (Typ) (dB) 83 Rating Catalog Operating temperature range (C) -40 to 125 Input bias current (Max) (pA) 60 Output current (Typ) (mA) 9 Features High Cload Drive Architecture CMOS THD + N @ 1 kHz (Typ) (%) 0.003 open-in-new Find other Precision op amps (Vos<1mV)

Package | Pins | Size

PDIP (N) 14 181 mm² 19.3 x 9.4 SOIC (D) 14 52 mm² 8.65 x 6 TSSOP (PW) 14 32 mm² 5 x 6.4 open-in-new Find other Precision op amps (Vos<1mV)

Features

  • Output Swing Includes Both Supply Rails
  • Low Noise...12 nV/ Hz Typ at f = 1 kHz
  • Low Input Bias Current...1 pA Typ
  • Fully Specified for Both Single-Supply and Split-Supply Operation
  • Low Power...500 µA Max
  • Common-Mode Input Voltage Range Includes Negative Rail
  • Low Input Offset Voltage
    950 µV Max at TA = 25°C (TLV226xA)
  • Wide Supply Voltage Range
    2.7 V to 8 V
  • Macromodel Included
  • Available in Q-Temp Automotive
    HighRel Automotive Applications
    Configuration Control / Print Support
    Qualification to Automotive Standards

Advanced LinCMOS is a trademark of Texas Instruments.

open-in-new Find other Precision op amps (Vos<1mV)

Description

The TLV2262 and TLV2264 are dual and quad low voltage operational amplifiers from Texas Instruments. Both devices exhibit rail-to-rail output performance for increased dynamic range in single or split supply applications. The TLV226x family offers a compromise between the micropower TLV225x and the ac performance of the TLC227x. It has low supply current for battery-powered applications, while still having adequate ac performance for applications that demand it. This family is fully characterized at 3 V and 5 V and is optimized for low-voltage applications. The noise performance has been dramatically improved over previous generations of CMOS amplifiers. Figure 1 depicts the low level of noise voltage for this CMOS amplifier, which has only 200 µA (typ) of supply current per amplifier.

The TLV226x, exhibiting high input impedance and low noise, are excellent for small-signal conditioning for high-impedance sources, such as piezoelectric transducers. Because of the micropower dissipation levels combined with 3-V operation, these devices work well in hand-held monitoring and remote-sensing applications. In addition, the rail-to-rail output feature with single or split supplies makes this family a great choice when interfacing with analog-to-digital converters (ADCs). For precision applications, the TLV226xA family is available and has a maximum input offset voltage of 950 µV.

The TLV2262/4 also makes great upgrades to the TLV2332/4 in standard designs. They offer increased output dynamic range, lower noise voltage and lower input offset voltage. This enhanced feature set allows them to be used in a wider range of applications. For applications that require higher output drive and wider input voltage range, see the TLV2432 and TLV2442 devices. If your design requires single amplifiers, please see the TLV2211/21/31 family. These devices are single rail-to-rail operational amplifiers in the SOT-23 package. Their small size and low power consumption, make them ideal for high density, battery-powered equipment.

open-in-new Find other Precision op amps (Vos<1mV)
Download

Technical documentation

= Top documentation for this product selected by TI
No results found. Please clear your search and try again. View all 4
Type Title Date
* Datasheet Advanced LinCMOS (TM) Rail-to-Rail Operational Amplifiers datasheet (Rev. C) Aug. 11, 2006
E-book The Signal e-book: A compendium of blog posts on op amp design topics Mar. 28, 2017
Application note TLV2262, TLV2264 EMI Immunity Performance Oct. 31, 2012
Application note Use of Rail-to-Rail Operational Amplifiers (Rev. A) Dec. 22, 1999

Design & development

For additional terms or required resources, click any title below to view the detail page where available.

Hardware development

EVALUATION BOARD Download
10
Description

Speed up your op amp prototyping and testing with the DIP-Adapter-EVM, which provides a fast, easy and inexpensive way to interface with small, surface-mount ICs. You can connect any supported op amp using the included Samtec terminal strips or wire them directly to existing circuits.

The (...)

Features
  • Simplifies prototyping of SMT IC’s
  • Supports 6 common package types
  • Low Cost
EVALUATION BOARD Download
Description
The DIYAMP-EVM is a unique evaluation module (EVM) family that provides engineers and do it yourselfers (DIYers) with real-world amplifier circuits, enabling you to quickly evaluate design concepts and verify simulations. It is available in three industry-standard packages (SC70, SOT23, SOIC) and 12 (...)
Features
  • 3 packages to choose from: SC70-5, SOT23-5 and SOIC-8
  • 12 circuit configurations to choose from: Noninverting, Inverting, Active Filters, Difference Amp, Comparator and more!
  • Dual and single supply configurations
  • PCB designed for High performance: Optimized for each function
  • Multiple interface options (...)
EVALUATION BOARD Download
Description

The Universal OPAMPEVM is a series of general purpose blank circuit boards that simplify prototyping circuits for a variety of IC package types. The evaluation module board design allows many different circuits to be constructed easily and quickly. Five models are offered with each targeted for (...)

Design tools & simulation

SIMULATION MODEL Download
SLOJ128A.ZIP (15 KB) - PSpice Model
SIMULATION TOOL Download
PSpice® for TI design and simulation tool
PSPICE-FOR-TI — PSpice® for TI is a design and simulation environment that helps evaluate functionality of analog circuits. This full-featured, design and simulation suite uses an analog analysis engine from Cadence®. Available at no cost, PSpice for TI includes one of the largest model libraries in the (...)
Features
  • Leverages Cadence PSpice Technology
  • Preinstalled library with a suite of digital models to enable worst-case timing analysis
  • Dynamic updates ensure you have access to most current device models
  • Optimized for simulation speed without loss of accuracy
  • Supports simultaneous analysis of multiple products
  • (...)
SIMULATION TOOL Download
SPICE-based analog simulation program
TINA-TI TINA-TI provides all the conventional DC, transient and frequency domain analysis of SPICE and much more. TINA has extensive post-processing capability that allows you to format results the way you want them. Virtual instruments allow you to select input waveforms and probe circuit nodes voltages (...)
CALCULATION TOOL Download
Analog engineer's calculator
ANALOG-ENGINEER-CALC — The Analog Engineer’s Calculator is designed to speed up many of the repetitive calculations that analog circuit design engineers use on a regular basis. This PC-based tool provides a graphical interface with a list of various common calculations ranging from setting op-amp gain with feedback (...)
Features
  • Expedites circuit design with analog-to-digital converters (ADCs) and digital-to-analog converters (DACs)
    • Noise calculations
    • Common unit translation
  • Solves common amplifier circuit design problems
    • Gain selections using standard resistors
    • Filter configurations
    • Total noise for common amplifier configurations
  • (...)
CALCULATION TOOL Download
Noise Calculator, Generator and Examples
OPAMP-NOISECALC This folder contains three tools to help in understandning and managing noise in cicuits. The included tools are:
  • A noise generator tool - This is a Lab View 4-Run Time executable that generates Gaussian white noise, uniform white noise, 1/f noise, short noise, and 60Hz line noise. Temporal data (...)
DESIGN TOOL Download
Single-supply, low-side, unidirectional current-sensing circuit
CIRCUIT060001 — This single–supply, low–side, current sensing solution accurately detects load current up to 1A and converts it to a voltage between 50mV and 4.9V. The input current range and output voltage range can be scaled as necessary and larger supplies can be used to accommodate larger swings.
Features
  • Senses Temperature between 25°C - 50°C 
  • Output: 0.05V - 3.25V 
  • Single 3.3V Supply with half-supply reference
DESIGN TOOL Download
Temperature sensing with NTC thermistor circuit
CIRCUIT060002 — This temperature sensing circuit uses a resistor in series with a negative–temperature–coefficient (NTC) thermistor to form a voltage divider, which has the effect of producing an output voltage that is linear over temperature. The circuit uses an op amp in a non–inverting (...)
Features
  • Senses Temperature between 25°C - 50°C 
  • Output: 0.05V - 3.25V 
  • Single 3.3V Supply with half-supply reference
DESIGN TOOL Download
Temperature sensing with PTC thermistor circuit
CIRCUIT060003 — This temperature sensing circuit uses a resistor in series with a positive–temperature–coefficient (PTC) thermistor to form a voltage–divider, which has the effect of producing an output voltage that is linear over temperature. The circuit uses an op amp in a non–inverting (...)
Features
  • Senses Temperature between 0°C - 50°C 
  • Output: 0.05V - 3.25V 
  • Single 3.3V Supply with half-supply reference
DESIGN TOOL Download
Low-noise and long-range PIR sensor conditioner circuit
CIRCUIT060004 — This two stage amplifier design amplifies and filters the signal from a passive infrared (PIR) sensor. The circuit includes multiple low–pass and high–pass filters to reduce noise at the output of the circuit to be able to detect motion at long distances and reduce false triggers. This (...)
Features
  • Single 5V Supply 
  • Passes frequencies between 0.7Hz - 10Hz 
  • AC Gain: 90dB
DESIGN TOOL Download
High-side current sensing with discrete difference amplifier circuit
CIRCUIT060005 — This single–supply, high–side, low–cost current sensing solution detects load current between 50mA and 1A and converters it to an output voltage from 0.25V to 5V. High–side sensing allows for the system to identify ground shorts and does not create a ground disturbance on the load.
Features
  • Single 36V supply 
  • Input: 50mA to 1A 
  • Output: 0.25V to 5V
DESIGN TOOL Download
Bridge amplifier circuit
CIRCUIT060006 — A strain gauge is a sensor whose resistance varies with applied force. To measure the variation in resistance, the strain gauge is placed in a bridge configuration. This design uses a 2 op amp instrumentation circuit to amplify a differential signal created by the change in resistance of a strain (...)
Features
  • Single 5V supply with half-supply reference
  • Input: -2.22mV to 2.27mV differential
  • Output: 225mV - 4.72V
  • Strain gauge resistance variation: 115 - 125 Ohms
  • Gain: 1001V/V
DESIGN TOOL Download
Low-side, bidirectional current-sensing circuit
CIRCUIT060007 — This single-supply low-side, bidirectional current sensing solution can accurately detect load currents from –1A to 1A. The linear range of the output is from 110mV to 3.19V. Low-side current sensing keeps the common-mode voltage near ground, and is thus most useful in applications with large (...)
Features
  • Single 5V supply with half-supply reference
  • Input: -2.22mV to 2.27mV differential
  • Output: 225mV - 4.72V 
  • Strain gauge resistance variation: 115 - 125 Ohms 
  • Gain: 1001V/V
DESIGN TOOL Download
Full-wave rectifier circuit
CIRCUIT060008 — This absolute value circuit can turn alternating current (AC) signals to single polarity signals. This circuit functions with limited distortion for ±10-V input signals at frequencies up to 50kHz and for signals as small as ±25mV at frequencies up to 1kHz.
Features
  • 30V Split supply with ground reference 
  • Input: +/-25mV to +/-10V 
  • Output: 25mV to 10V
DESIGN TOOL Download
Half-wave rectifier circuit
CIRCUIT060009 — The precision half-wave rectifier inverts and transfers only the negative-half input of a time varying input signal (preferably sinusoidal) to its output. By appropriately selecting the feedback resistor values, different gains can be achieved. Precision half-wave rectifiers are commonly used with (...)
Features
  • 5V Split supply 
  • Input: +/-0.2mVpp to +/-4Vpp 
  • Output: 0.1V to 2V
DESIGN TOOL Download
PWM generator circuit
CIRCUIT060010 — This circuit utilizes a triangle wave generator and comparator to generate a 500 kHz pulse-width modulated (PWM) waveform with a duty cycle that is inversely proportional to the input voltage. An op amp and comparator generate a triangle waveform which is applied to the inverting input of a second (...)
Features
  • 5V Single supply with half-supply reference 
  • Input: -2V to 2V 
  • Output: 0V to 5V

CAD/CAE symbols

Package Pins Download
PDIP (N) 14 View options
SOIC (D) 14 View options
TSSOP (PW) 14 View options

Ordering & quality

Information included:
  • RoHS
  • REACH
  • Device marking
  • Lead finish/Ball material
  • MSL rating/Peak reflow
  • MTBF/FIT estimates
  • Material content
  • Qualification summary
  • Ongoing reliability monitoring

Support & training

TI E2E™ forums with technical support from TI engineers

Content is provided "as is" by TI and community contributors and does not constitute TI specifications. See terms of use.

If you have questions about quality, packaging or ordering TI products, see TI support. ​​​​​​​​​​​​​​

Videos

Related videos