SWCU195A December   2024  – May 2025 CC2744R7-Q1 , CC2745P10-Q1 , CC2745R10-Q1 , CC2745R7-Q1 , CC2755R10

 

  1.   1
  2.   Read This First
    1.     About This Manual
    2.     Devices
    3.     Register, Field, and Bit Calls
    4.     Related Documentation
    5.     Trademarks
  3. 1 Architectural Overview
    1. 1.1  Target Applications
    2. 1.2  Introduction
    3. 1.3  Arm Cortex M33
      1. 1.3.1 Processor Core
      2. 1.3.2 SysTick Timer
      3. 1.3.3 Nested Vectored Interrupt Controller
      4. 1.3.4 System Control Block (SCB)
      5. 1.3.5 TI Machine Learning Instruction Extensions
    4. 1.4  On-Chip Memory
      1. 1.4.1 SRAM
      2. 1.4.2 FLASH
      3. 1.4.3 ROM
    5. 1.5  Power Supply System
      1. 1.5.1 VDDS
      2. 1.5.2 VDDIO
      3. 1.5.3 VDDR
      4. 1.5.4 VDDD Digital Core Supply
      5. 1.5.5 DC/DC Converter
    6. 1.6  Radio
    7. 1.7  Hardware Security Module
    8. 1.8  AES 128-Bit Cryptographic Accelerator
    9. 1.9  System Timer (SYSTIM)
    10. 1.10 General Purpose Timers (LGPT)
    11. 1.11 Always-ON (AON) or Ultra-Low Leakage (ULL) Domain
      1. 1.11.1 Watchdog Timer
      2. 1.11.2 Battery and Temperature Monitor
      3. 1.11.3 Voltage Glitch Monitor (VGM)
      4. 1.11.4 Real-Time Clock (RTC)
      5. 1.11.5 Low Power Comparator
    12. 1.12 Direct Memory Access
    13. 1.13 System Control and Clock
    14. 1.14 Communication Peripherals
      1. 1.14.1 UART
      2. 1.14.2 I2C
      3. 1.14.3 SPI
      4. 1.14.4 CAN-FD
      5. 1.14.5 I2S
    15. 1.15 Programmable I/Os
    16. 1.16 Algorithm Processing Unit (APU)
    17. 1.17 Serial Wire Debug (SWD)
  4. 2 Arm® Cortex®-M33 Processor
    1. 2.1 Arm® Cortex®-M33 Processor Introduction
    2. 2.2 M33 Instantiation Parameters
    3. 2.3 Arm® Cortex®-M33 System Peripheral Details
      1. 2.3.1 Floating Point Unit (FPU)
      2. 2.3.2 Memory Protection Unit (MPU)
      3. 2.3.3 Digital Signal Processing (DSP)
      4. 2.3.4 Security Attribution Unit (SAU)
      5. 2.3.5 System Timer (SysTick)
      6. 2.3.6 Nested Vectored Interrupt Controller (NVIC)
      7. 2.3.7 System Control Block (SCB)
      8. 2.3.8 System Control Space (SCS)
    4. 2.4 CPU Sub-System Peripheral Details
      1. 2.4.1 Trace Port Interface Unit (TPIU)
      2. 2.4.2 DAP Bridge and Debug Authentication
      3. 2.4.3 Implementation Defined Attribution Unit (IDAU)
      4. 2.4.4 Custom Datapath Extension (CDE)
    5. 2.5 Programming Model
      1. 2.5.1 Modes of Operation and Execution
        1. 2.5.1.1 Security States
        2. 2.5.1.2 Operating Modes
        3. 2.5.1.3 Operating States
        4. 2.5.1.4 Privileged Access and Unprivileged User Access
      2. 2.5.2 Instruction Set Summary
      3. 2.5.3 Memory Model
        1. 2.5.3.1 Private Peripheral Bus
        2. 2.5.3.2 Unaligned Accesses
      4. 2.5.4 Processor Core Registers Summary
      5. 2.5.5 Exceptions
        1. 2.5.5.1 Exception Handling and Prioritization
    6. 2.6 TrustZone-M
      1. 2.6.1 Overview
      2. 2.6.2 M33 Configuration
      3. 2.6.3 Description of Elements
        1. 2.6.3.1 IDAU (Implementation Defined Attribution Unit)
          1. 2.6.3.1.1 Expected Use
        2. 2.6.3.2 Gaskets
          1. 2.6.3.2.1 Periphery Gasket
          2. 2.6.3.2.2 Controller Gasket
        3. 2.6.3.3 Memories
        4. 2.6.3.4 TCM
      4. 2.6.4 TCM Registers
    7. 2.7 Arm® Cortex®-M33 Registers
      1. 2.7.1  CPU_ROM_TABLE Registers
      2. 2.7.2  TPIU Registers
      3. 2.7.3  DCB Registers
      4. 2.7.4  DIB Registers
      5. 2.7.5  DWT Registers
      6. 2.7.6  FPB Registers
      7. 2.7.7  FPE Registers
      8. 2.7.8  ICB Registers
      9. 2.7.9  ITM Registers
      10. 2.7.10 MPU Registers
      11. 2.7.11 NVIC Registers
      12. 2.7.12 SAU Registers
      13. 2.7.13 SCB Registers
      14. 2.7.14 SYSTIMER Registers
      15. 2.7.15 SYSTICK Registers
      16. 2.7.16 Clock Control
      17. 2.7.17 Protocol Descriptions
      18. 2.7.18 Reset Considerations
        1. 2.7.18.1 Hardware Reset Considerations
      19. 2.7.19 Initialization
      20. 2.7.20 Interrupt and Event Support
        1. 2.7.20.1 Connection to Event Fabric
      21. 2.7.21 Power Management
  5. 3 Memory Map
    1. 3.1 Memory Map
  6. 4 Interrupts and Events
    1. 4.1 Exception Model
      1. 4.1.1 Exception States
      2. 4.1.2 Exception Types
      3. 4.1.3 Exception Handlers
      4. 4.1.4 Vector Table
      5. 4.1.5 Exception Priorities
      6. 4.1.6 Interrupt Priority Grouping
      7. 4.1.7 Exception Entry and Return
        1. 4.1.7.1 Exception Entry
        2. 4.1.7.2 Exception Return
    2. 4.2 Fault Handling
      1. 4.2.1 Fault Types
      2. 4.2.2 Fault Escalation to HardFault
      3. 4.2.3 Fault Status Registers and Fault Address Registers
      4. 4.2.4 Lockup
    3. 4.3 Security State Switches
    4. 4.4 Event Fabric
      1. 4.4.1 Introduction
      2. 4.4.2 Overview
      3. 4.4.3 Registers
      4. 4.4.4 AON Event Fabric
        1. 4.4.4.1 AON Common Input Events List
        2. 4.4.4.2 AON Event Subscribers
        3. 4.4.4.3 Power Management Controller (PMCTL)
        4. 4.4.4.4 Real Time Clock (RTC)
        5. 4.4.4.5 AON to MCU Event Fabric
      5. 4.4.5 MCU Event Fabric
        1. 4.4.5.1 Common Input Event List
        2. 4.4.5.2 MCU Event Subscribers
          1. 4.4.5.2.1 System CPU
          2. 4.4.5.2.2 Non-Maskable Interrupt (NMI)
    5. 4.5 Digital Test Bus (DTB)
    6. 4.6 EVTSVT Registers
    7. 4.7 EVTULL Registers
  7. 5 Debug Subsystem
    1. 5.1  Introduction
    2. 5.2  Block Diagram
    3. 5.3  Overview
      1. 5.3.1 Physical Interface
      2. 5.3.2 Debug Access Ports
    4. 5.4  Debug Features
      1. 5.4.1 Processor Debug
      2. 5.4.2 Breakpoint Unit (BPU)
      3. 5.4.3 Peripheral Debug
    5. 5.5  Behavior in Low Power Modes
    6. 5.6  Restricting Debug Access
    7. 5.7  Mailbox (DSSM)
    8. 5.8  Mailbox Events
      1. 5.8.1 CPU Interrupt Event (AON_DBG_COMB)
    9. 5.9  Software Considerations
    10. 5.10 DBGSS Registers
  8. 6 Power, Reset, and Clocking
    1. 6.1 Introduction
    2. 6.2 System CPU Modes
    3. 6.3 Supply System
      1. 6.3.1 Internal DC/DC Converter and Global LDO
    4. 6.4 Power States
      1. 6.4.1 RESET
      2. 6.4.2 SHUTDOWN
      3. 6.4.3 ACTIVE
      4. 6.4.4 IDLE
      5. 6.4.5 STANDBY
      6. 6.4.6 PMCTL Registers
    5. 6.5 Digital Power Partitioning
    6. 6.6 Clocks
      1. 6.6.1 Block Diagram
      2. 6.6.2 LF clock
        1. 6.6.2.1 LFINC Measurement Mechanism
        2. 6.6.2.2 LFINC Filtering
      3. 6.6.3 HFOSC
        1. 6.6.3.1 HFOSC Control and Qualification
        2. 6.6.3.2 HFOSC Tracking Loop
      4. 6.6.4 AFOSC
        1. 6.6.4.1 AFOSC Control and Qualification
        2. 6.6.4.2 AFOSC Tracking Loop
        3. 6.6.4.3 AFOSC Ratio
      5. 6.6.5 CLKSVT
      6. 6.6.6 CLKULL
      7. 6.6.7 CKM Registers
      8. 6.6.8 CKMD Registers
      9. 6.6.9 CLKCTL Registers
    7. 6.7 Resets
      1. 6.7.1 Watchdog Timer (WDT)
      2. 6.7.2 RTC Reset
      3. 6.7.3 LF Loss Detection
    8. 6.8 AON (REG3V3) Register Bank
  9. 7 Internal Memory
    1. 7.1 SRAM
      1. 7.1.1 Overview
        1. 7.1.1.1 Purpose of the Peripheral
        2. 7.1.1.2 Features
        3. 7.1.1.3 Functional Block Diagram
      2. 7.1.2 Peripheral Functional Description
        1. 7.1.2.1 Parity Error Detection
          1. 7.1.2.1.1 Parity Error Debug Register
        2. 7.1.2.2 Extension Mode
        3. 7.1.2.3 Initialization
        4. 7.1.2.4 TrustZone Watermarking
      3. 7.1.3 SRAM Registers
      4. 7.1.4 SRAMCTRL Registers
    2. 7.2 VIMS
      1. 7.2.1 Overview
        1. 7.2.1.1 Purpose of the Peripheral
        2. 7.2.1.2 Features
        3. 7.2.1.3 Functional Block Diagram
      2. 7.2.2 Peripheral Functional Description
        1. 7.2.2.1 Dedicated 8KB CPU Cache
        2. 7.2.2.2 Dedicated 2KB HSM Cache
        3. 7.2.2.3 Dedicated 128-Bit Line Buffer
        4. 7.2.2.4 ROM
        5. 7.2.2.5 Flash
        6. 7.2.2.6 Auxiliary Regions
        7. 7.2.2.7 Flash Partition and Protection
          1. 7.2.2.7.1 Main Region
          2. 7.2.2.7.2 Read Protection
          3. 7.2.2.7.3 Sticky Write/Erase Protection
        8. 7.2.2.8 TrustZoneTM Watermark
        9. 7.2.2.9 Debug Access
      3. 7.2.3 VIMS Registers
    3. 7.3 FLASH
      1. 7.3.1 FLASH Registers
  10. 8 Hardware Security Module (HSM)
    1. 8.1 Introduction
    2. 8.2 Overview
    3. 8.3 One-Time-Programmable (OTP) Controller
      1. 8.3.1 High-Level Sequence to Handle OTP Requests
    4. 8.4 Mailbox and Register Access Firewall
    5. 8.5 DMA Firewall
    6. 8.6 Coprocessor
    7. 8.7 HSM FW
      1. 8.7.1 Acquiring the Latest HSM FW
      2. 8.7.2 Programming HSM FW
      3. 8.7.3 Optional Customer Signing of HSM FW
    8. 8.8 HSM Registers
    9. 8.9 HSMCRYPTO Registers
  11. 9 Device Boot and Bootloader
    1. 9.1 Device Boot and Programming
      1. 9.1.1 Boot Flow
      2. 9.1.2 Boot Status
      3. 9.1.3 Boot Protection/Locking Mechanisms
      4. 9.1.4 Debug and Active SWD Connections at Boot
        1. 9.1.4.1 Secure Debug and Persistent Debug
      5. 9.1.5 Flashless Test Mode and Tools Client Mode
        1. 9.1.5.1 Flashless Test Mode
        2. 9.1.5.2 Tools Client Mode
      6. 9.1.6 Retest Mode and Return-to-Factory Procedure
      7. 9.1.7 Disabling SWD Debug Port
    2. 9.2 Flash Programming
      1. 9.2.1 CCFG
      2. 9.2.2 CCFG Permissions/Restrictions that Affect Flash Programming
      3. 9.2.3 SACI Flash Programming Commands
      4. 9.2.4 Flash Programming Flows
        1. 9.2.4.1 Initial Programming of a New Device
        2. 9.2.4.2 Reprogramming of Previously Programmed Device
        3. 9.2.4.3 Add User Record on Already Programmed Device as Part of Commissioning Step
        4. 9.2.4.4 Incrementally Program Ancillary Data to MAIN Flash Sectors of a Previously Programmed Device
        5. 9.2.4.5 Reprogramming of Only the Main Flash Application of a Previously Programmed Device
    3. 9.3 Device Management Command Interface
      1. 9.3.1 SACI Communication Protocol
        1. 9.3.1.1 Host Side Protocol
        2. 9.3.1.2 Command Format
        3. 9.3.1.3 Response Format
        4. 9.3.1.4 Response Result Field
        5. 9.3.1.5 Command Sequence Tag
        6. 9.3.1.6 Host Side Timeout
      2. 9.3.2 SACI Commands
        1. 9.3.2.1 Miscellaneous Commands
          1. 9.3.2.1.1 SACI_CMD_MISC_NO_OPERATION
          2. 9.3.2.1.2 SACI_CMD_MISC_GET_DIE_ID
          3. 9.3.2.1.3 SACI_CMD_MISC_GET_CCFG_USER_REC
          4. 9.3.2.1.4 SACI_CMD_GET_SECBOOT_HSMFW_UPDATE_STATUS
          5. 9.3.2.1.5 SACI_CMD_HSM_GET_SYS_INFO
        2. 9.3.2.2 Debug Commands
          1. 9.3.2.2.1 SACI_CMD_DEBUG_EXIT_SACI_HALT
          2. 9.3.2.2.2 SACI_CMD_DEBUG_EXIT_SACI_SHUTDOWN
          3. 9.3.2.2.3 SACI_CMD_DEBUG_REQ_KEY_ID
          4. 9.3.2.2.4 SACI_CMD_DEBUG_REQ_CHALLENGE
          5. 9.3.2.2.5 SACI_CMD_DEBUG_SUBMIT_CHALLENGE_RESP
          6. 9.3.2.2.6 SACI_CMD_DEBUG_CLOSE_SESSION
          7. 9.3.2.2.7 SACI_CMD_BLDR_APP_RESET_DEVICE
          8. 9.3.2.2.8 SACI_CMD_BLDR_APP_EXIT_SACI_RUN
        3. 9.3.2.3 Flash Programming Commands
          1. 9.3.2.3.1  SACI_CMD_FLASH_ERASE_CHIP
          2. 9.3.2.3.2  SACI_CMD_FLASH_ERASE_MAIN_APP
          3. 9.3.2.3.3  SACI_CMD_FLASH_PROG_CCFG_SECTOR
          4. 9.3.2.3.4  SACI_CMD_FLASH_PROG_CCFG_USER_REC
          5. 9.3.2.3.5  SACI_CMD_FLASH_PROG_SCFG_SECTOR
          6. 9.3.2.3.6  SACI_CMD_FLASH_PROG_MAIN_SECTOR
          7. 9.3.2.3.7  SACI_CMD_FLASH_PROG_MAIN_PIPELINED
          8. 9.3.2.3.8  SACI_CMD_FLASH_VERIFY_MAIN_SECTORS
          9. 9.3.2.3.9  SACI_CMD_FLASH_VERIFY_CCFG_SECTOR
          10. 9.3.2.3.10 SACI_CMD_FLASH_VERIFY_SCFG_SECTOR
    4. 9.4 Bootloader Support
      1. 9.4.1 Bootloader v.s Secure Boot
    5. 9.5 ROM Serial Bootloader
      1. 9.5.1 ROM Serial Bootloader Interfaces
        1. 9.5.1.1 Packet Handling
          1. 9.5.1.1.1 Packet Acknowledge and Not-Acknowledge Bytes
        2. 9.5.1.2 Transport Layer
          1. 9.5.1.2.1 UART Transport
            1. 9.5.1.2.1.1 UART Baud Rate Automatic Detection
          2. 9.5.1.2.2 SPI Transport
      2. 9.5.2 ROM Serial Bootloader Parameters
      3. 9.5.3 ROM Serial Bootloader Commands
        1. 9.5.3.1 BLDR_CMD_PING
        2. 9.5.3.2 BLDR_CMD_GET_STATUS
        3. 9.5.3.3 BLDR_CMD_GET_PART_ID
        4. 9.5.3.4 BLDR_CMD_RESET
        5. 9.5.3.5 BLDR_CMD_CHIP_ERASE
        6. 9.5.3.6 BLDR_CMD_CRC32
        7. 9.5.3.7 BLDR_CMD_DOWNLOAD
        8. 9.5.3.8 BLDR_CMD_DOWNLOAD_CRC
        9. 9.5.3.9 BLDR_CMD_SEND_DATA
      4. 9.5.4 Bootloader Firmware Update Example
  12. 10Device Configuration
    1. 10.1 Guidelines for Securely Configuring Your Device
      1. 10.1.1 Enabling and Configuring Secure Boot
      2. 10.1.2 Configure Debug Access
      3. 10.1.3 Configure Flash Protections
      4. 10.1.4 Configure Device Permissions
      5. 10.1.5 Configure HSM FW Update Keys
      6. 10.1.6 Configure emSensor
    2. 10.2 Factory Configuration (FCFG)
    3. 10.3 Customer Configuration (CCFG)
    4. 10.4 Security Configuration (SCFG)
  13. 11Secure Boot
    1. 11.1  Secure Boot
    2. 11.2  Execution Flow
    3. 11.3  ROM API
      1. 11.3.1 HAPI (Hardware API)
      2. 11.3.2 Registers
    4. 11.4  Configuration
      1. 11.4.1 Slot Configuration
      2. 11.4.2 Policy
        1. 11.4.2.1 Authentication Method
        2. 11.4.2.2 Authentication Algorithm
        3. 11.4.2.3 Update Mode
          1. 11.4.2.3.1 Overwrite
          2. 11.4.2.3.2 XIP Revert Enabled/Disabled
      3. 11.4.3 Key Update Key Hash
      4. 11.4.4 Key Ring
      5. 11.4.5 Boot Seed
    5. 11.5  Generic Image Format
    6. 11.6  Application Update
      1. 11.6.1 Image Format
    7. 11.7  Secondary Secure Bootloader Update
      1. 11.7.1 Image Format
      2. 11.7.2 Update Pattern
    8. 11.8  Key Update
      1. 11.8.1 Image Format
    9. 11.9  Antirollback
    10. 11.10 Version Log (VLOG)
      1. 11.10.1 Record structure
    11. 11.11 Fallback
    12. 11.12 ROM Panic
  14. 12General Purpose Timers (LGPT)
    1. 12.1 Overview
    2. 12.2 Block Diagram
    3. 12.3 Functional Description
      1. 12.3.1  Prescaler
      2. 12.3.2  Counter
      3. 12.3.3  Target
      4. 12.3.4  Channel Input Logic
      5. 12.3.5  Channel Output Logic
      6. 12.3.6  Channel Actions
        1. 12.3.6.1 Period and Pulse Width Measurement
        2. 12.3.6.2 Clear on Zero, Toggle on Compare Repeatedly
        3. 12.3.6.3 Set on Zero, Toggle on Compare Repeatedly
      7. 12.3.7  Channel Capture Configuration
      8. 12.3.8  Channel Filters
        1. 12.3.8.1 Setting up the Channel Filters
      9. 12.3.9  Synchronize Multiple LGPT Timers
      10. 12.3.10 Interrupts, ADC Trigger, and DMA Request
    4. 12.4 Timer Modes
      1. 12.4.1 Quadrature Decoder
      2. 12.4.2 DMA
      3. 12.4.3 IR Generation
      4. 12.4.4 Fault and Park
      5. 12.4.5 Deadband
      6. 12.4.6 Deadband, Fault, and Park
      7. 12.4.7 Example Application: Brushless DC (BLDC) Motor
    5. 12.5 LGPT0 Registers
    6. 12.6 LGPT1 Registers
    7. 12.7 LGPT2 Registers
    8. 12.8 LGPT3 Registers
  15. 13Algorithm Processing Unit (APU)
    1. 13.1 Introduction
    2. 13.2 APU Related Collateral
    3. 13.3 Functional Description
    4. 13.4 APU Operation
    5. 13.5 Interrupts and Events
    6. 13.6 Data Representation
    7. 13.7 Data Memory
    8. 13.8 Software
    9. 13.9 APU Registers
  16. 14Voltage Glitch Monitor (VGM)
    1. 14.1 Overview
    2. 14.2 Features and Operation
  17. 15System Timer (SYSTIM)
    1. 15.1 Overview
    2. 15.2 Block Diagram
    3. 15.3 Functional Description
      1. 15.3.1 Common Channel Features
        1. 15.3.1.1 Compare Mode
        2. 15.3.1.2 Capture Mode
        3. 15.3.1.3 Additional Channel Arming Methods
      2. 15.3.2 Interrupts and Events
    4. 15.4 SYSTIM Registers
  18. 16Real Time Clock (RTC)
    1. 16.1 Introduction
    2. 16.2 Block Diagram
    3. 16.3 Interrupts and Events
      1. 16.3.1 Input Event
      2. 16.3.2 Output Event
      3. 16.3.3 Arming and Disarming Channels
    4. 16.4 CAPTURE and COMPARE Configurations
      1. 16.4.1 CHANNEL 0 - COMPARE CHANNEL
      2. 16.4.2 CHANNEL 1—CAPTURE CHANNEL
    5. 16.5 RTC Registers
  19. 17Low Power Comparator (SYS0)
    1. 17.1 Introduction
    2. 17.2 Block Diagram
    3. 17.3 Functional Description
      1. 17.3.1 Input Selection
      2. 17.3.2 Voltage Divider
      3. 17.3.3 Hysteresis
      4. 17.3.4 Wake-Up
    4. 17.4 SYS0 Registers
  20. 18Battery Monitor, Temperature Sensor, and DCDC Controller (PMUD)
    1. 18.1 Introduction
    2. 18.2 Functional Description
      1. 18.2.1 BATMON
      2. 18.2.2 DCDC
    3. 18.3 PMUD Registers
  21. 19Micro Direct Memory Access (µDMA)
    1. 19.1 Introduction
    2. 19.2 Block Diagram
    3. 19.3 Functional Description
      1. 19.3.1  Channel Assignments
      2. 19.3.2  Priority
      3. 19.3.3  Arbitration Size
      4. 19.3.4  Request Types
        1. 19.3.4.1 Single Request
        2. 19.3.4.2 Burst Request
      5. 19.3.5  Channel Configuration
      6. 19.3.6  Transfer Modes
        1. 19.3.6.1 Stop Mode
        2. 19.3.6.2 Basic Mode
        3. 19.3.6.3 Auto Mode
        4. 19.3.6.4 Ping-Pong Mode
        5. 19.3.6.5 Memory Scatter-Gather Mode
        6. 19.3.6.6 Peripheral Scatter-Gather Mode
      7. 19.3.7  Transfer Size and Increments
      8. 19.3.8  Peripheral Interface
      9. 19.3.9  Software Request
      10. 19.3.10 Interrupts and Errors
      11. 19.3.11 Initialization and Configuration
        1. 19.3.11.1 Module Initialization
        2. 19.3.11.2 Configuring a Memory-to-Memory Transfer
        3. 19.3.11.3 Configure the Channel Attributes
        4. 19.3.11.4 Configure the Channel Control Structure
        5. 19.3.11.5 Start the Transfer
        6. 19.3.11.6 Software Considerations
    4. 19.4 DMA Registers
  22. 20Advanced Encryption Standard (AES)
    1. 20.1 Introduction
      1. 20.1.1 AES Performance
    2. 20.2 Functional Description
      1. 20.2.1 Reset Considerations
      2. 20.2.2 Interrupt and Event Support
        1. 20.2.2.1 Interrupt Events and Requests
        2. 20.2.2.2 Connection to Event Fabric
      3. 20.2.3 µDMA
        1. 20.2.3.1 µDMA Example
    3. 20.3 Encryption and Decryption Configuration
      1. 20.3.1  CBC-MAC (Cipher Block Chaining-Message Authentication Code)
      2. 20.3.2  CBC (Cipher Block Chaining) Encryption
      3. 20.3.3  CBC Decryption
      4. 20.3.4  CTR (Counter) Encryption/Decryption
      5. 20.3.5  ECB (Electronic Code Book) Encryption
      6. 20.3.6  ECB Decryption
      7. 20.3.7  CFB (Cipher Feedback) Encryption
      8. 20.3.8  CFB Decryption
      9. 20.3.9  OFB (Open Feedback) Encryption
      10. 20.3.10 OFB Decryption
      11. 20.3.11 PCBC (Propagating Cipher Block Chaining) Encryption
      12. 20.3.12 PCBC Decryption
      13. 20.3.13 CTR-DRBG (Counter-Deterministic Random Bit Generator)
      14. 20.3.14 CCM
    4. 20.4 AES Registers
    5. 20.5 CRYPTO Registers
  23. 21Analog to Digital Converter (ADC)
    1. 21.1 Overview
    2. 21.2 Block Diagram
    3. 21.3 Functional Description
      1. 21.3.1  ADC Core
      2. 21.3.2  Voltage Reference Options
      3. 21.3.3  Resolution Modes
      4. 21.3.4  ADC Clocking
      5. 21.3.5  Power Down Behavior
      6. 21.3.6  Sampling Trigger Sources and Sampling Modes
        1. 21.3.6.1 AUTO Sampling Mode
        2. 21.3.6.2 MANUAL Sampling Mode
      7. 21.3.7  Sampling Period
      8. 21.3.8  Conversion Modes
      9. 21.3.9  ADC Data Format
      10. 21.3.10 Status Register
      11. 21.3.11 ADC Events
        1. 21.3.11.1 CPU Interrupt Event Publisher (INT_EVENT0)
        2. 21.3.11.2 Generic Event Publisher (INT_EVENT1)
        3. 21.3.11.3 DMA Trigger Event Publisher (INT_EVENT2)
        4. 21.3.11.4 Generic Event Subscriber
    4. 21.4 Advanced Features
      1. 21.4.1 Window Comparator
      2. 21.4.2 DMA & FIFO Operation
        1. 21.4.2.1 DMA/CPU Operation in Non-FIFO Mode (FIFOEN=0)
        2. 21.4.2.2 DMA/CPU Operation in FIFO Mode (FIFOEN=1)
        3. 21.4.2.3 DMA/CPU Operation Summary Matrix
      3. 21.4.3 Ad-hoc Single Conversion
    5. 21.5 ADC Registers
  24. 22I/O Controller (IOC)
    1. 22.1  Introduction
    2. 22.2  Block Diagram
    3. 22.3  I/O Mapping and Configuration
      1. 22.3.1 Basic I/O Mapping
      2. 22.3.2 Radio GPO
      3. 22.3.3 Pin Mapping
      4. 22.3.4 DTB Muxing
    4. 22.4  Edge Detection
    5. 22.5  GPIO
    6. 22.6  I/O Pins
    7. 22.7  Unused Pins
    8. 22.8  Debug Configuration
    9. 22.9  IOC Registers
    10. 22.10 GPIO Registers
  25. 23Universal Asynchronous Receiver/Transmitter (UART-LIN)
    1. 23.1 Introduction
    2. 23.2 Block Diagram
    3. 23.3 UART Functional Description
      1. 23.3.1 Transmit and Receive Logic
      2. 23.3.2 Baud Rate Generation
      3. 23.3.3 FIFO Operation
        1. 23.3.3.1 FIFO Remapping
      4. 23.3.4 Data Transmission
      5. 23.3.5 Flow Control
      6. 23.3.6 IrDA Encoding and Decoding
      7. 23.3.7 Interrupts
      8. 23.3.8 Loopback Operation
    4. 23.4 UART-LIN Specification
      1. 23.4.1 Break transmission in UART mode
      2. 23.4.2 Break reception in UART mode
      3. 23.4.3 Break/Synch transmission in LIN mode
      4. 23.4.4 Break/Synch reception in LIN mode
      5. 23.4.5 Dormant mode operation
      6. 23.4.6 Wakeup signal generation
      7. 23.4.7 Wakeup signal detection when device is in active/idle modes
      8. 23.4.8 Wakeup signal detection when device is in standby mode
    5. 23.5 Interface to µDMA
    6. 23.6 Initialization and Configuration
    7. 23.7 UART Registers
  26. 24Serial Peripheral Interface (SPI)
    1. 24.1 Overview
      1. 24.1.1 Features
      2. 24.1.2 Block Diagram
    2. 24.2 Signal Description
    3. 24.3 Functional Description
      1. 24.3.1  Clock Control
      2. 24.3.2  FIFO Operation
        1. 24.3.2.1 Transmit FIFO
        2. 24.3.2.2 Repeated Transmit Operation
        3. 24.3.2.3 Receive FIFO
        4. 24.3.2.4 FIFO Flush
      3. 24.3.3  Interrupts
      4. 24.3.4  Data Format
      5. 24.3.5  Delayed Data Sampling
      6. 24.3.6  Chip Select Control
      7. 24.3.7  Command Data Control
      8. 24.3.8  Protocol Descriptions
        1. 24.3.8.1 Motorola SPI Frame Format
        2. 24.3.8.2 Texas Instruments Synchronous Serial Frame Format
        3. 24.3.8.3 MICROWIRE Frame Format
      9. 24.3.9  CRC Configuration
      10. 24.3.10 Auto CRC Functionality
      11. 24.3.11 Auto Header Functionality
      12. 24.3.12 SPI Status
      13. 24.3.13 Debug Halt
    4. 24.4 µDMA Operation
    5. 24.5 Initialization and Configuration
    6. 24.6 SPI Registers
  27. 25Inter-Integrated Circuit (I2C)
    1. 25.1 Introduction
    2. 25.2 Block Diagram
    3. 25.3 Functional Description
      1. 25.3.1 Functional Overview
        1. 25.3.1.1 Start and Stop Conditions
        2. 25.3.1.2 Data Format with 7-Bit Address
        3. 25.3.1.3 Data Validity
        4. 25.3.1.4 Acknowledge
        5. 25.3.1.5 Arbitration
      2. 25.3.2 Available Speed Modes
      3. 25.3.3 Interrupts
        1. 25.3.3.1 I2C Controller Interrupts
        2. 25.3.3.2 I2C Target Interrupts
      4. 25.3.4 Loopback Operation
      5. 25.3.5 Command Sequence Flowcharts
        1. 25.3.5.1 I2C Controller Command Sequences
        2. 25.3.5.2 I2C Target Command Sequences
    4. 25.4 Initialization and Configuration
    5. 25.5 I2C Registers
  28. 26Inter-IC Sound (I2S)
    1. 26.1  Introduction
    2. 26.2  Block Diagram
    3. 26.3  Clock Architecture
    4. 26.4  Signal Descriptions
    5. 26.5  Functional Description
      1. 26.5.1 Pin Configuration
      2. 26.5.2 Serial Format Configuration
      3. 26.5.3 I2S Format Schematic
        1. 26.5.3.1 Register Configuration
      4. 26.5.4 Left-Justified (LJF)
        1. 26.5.4.1 Register Configuration
      5. 26.5.5 Right-Justified (RJF)
        1. 26.5.5.1 Register Configuration
      6. 26.5.6 DSP
        1. 26.5.6.1 Register Configuration
      7. 26.5.7 Clock Configuration
    6. 26.6  Memory Interface
      1. 26.6.1 Sample Word Length
      2. 26.6.2 Padding Mechanism
      3. 26.6.3 Channel Mapping
      4. 26.6.4 Sample Storage in Memory
      5. 26.6.5 DMA Operation
        1. 26.6.5.1 Start-Up
        2. 26.6.5.2 Operation
        3. 26.6.5.3 Shutdown
    7. 26.7  Samplestamp Generator
      1. 26.7.1 Samplestamp Counters
      2. 26.7.2 Start-Up Triggers
      3. 26.7.3 Samplestamp Capture
      4. 26.7.4 Achieving Constant Audio Latency
    8. 26.8  Error Detection
    9. 26.9  Usage
      1. 26.9.1 Start-Up Sequence
      2. 26.9.2 Shutdown Sequence
    10. 26.10 I2S Configuration Guideline
    11. 26.11 I2S Registers
  29. 27CAN-FD
    1. 27.1 Introduction
    2. 27.2 Functions
    3. 27.3 MCAN Subsystem
    4. 27.4 MCAN Functional Description
      1. 27.4.1 Operating Modes
        1. 27.4.1.1 Software Initialization
        2. 27.4.1.2 Normal Operation
        3. 27.4.1.3 CAN FD Operation
        4. 27.4.1.4 Transmitter Delay Compensation
          1. 27.4.1.4.1 Description
          2. 27.4.1.4.2 Transmitter Delay Compensation Measurement
        5. 27.4.1.5 Restricted Operation Mode
        6. 27.4.1.6 Bus Monitoring Mode
        7. 27.4.1.7 Disabled Automatic Retransmission
          1. 27.4.1.7.1 Frame Transmission in DAR Mode
        8. 27.4.1.8 Power Down (Sleep Mode)
          1. 27.4.1.8.1 MCAN Clock Stop and Wake Operations
          2. 27.4.1.8.2 MCAN Debug Suspend Operation
        9. 27.4.1.9 Test Modes
          1. 27.4.1.9.1 External Loop Back Mode
          2. 27.4.1.9.2 Internal Loop Back Mode
      2. 27.4.2 Timestamp Generation
        1. 27.4.2.1 External Timestamp Counter
        2. 27.4.2.2 Block Diagram
      3. 27.4.3 Timeout Counter
      4. 27.4.4 Rx Handling
        1. 27.4.4.1 Acceptance Filtering
          1. 27.4.4.1.1 Range Filter
          2. 27.4.4.1.2 Filter for specific IDs
          3. 27.4.4.1.3 Classic Bit Mask Filter
          4. 27.4.4.1.4 Standard Message ID Filtering
          5. 27.4.4.1.5 Extended Message ID Filtering
        2. 27.4.4.2 Rx FIFOs
          1. 27.4.4.2.1 Rx FIFO Blocking Mode
          2. 27.4.4.2.2 Rx FIFO Overwrite Mode
        3. 27.4.4.3 Dedicated Rx Buffers
          1. 27.4.4.3.1 Rx Buffer Handling
        4. 27.4.4.4 Debug on CAN Support
          1. 27.4.4.4.1 Filtering for Debug Messages
          2. 27.4.4.4.2 Debug Message Handling
      5. 27.4.5 Tx Handling
        1. 27.4.5.1 Transmit Pause
        2. 27.4.5.2 Dedicated Tx Buffers
        3. 27.4.5.3 Tx FIFO
        4. 27.4.5.4 Tx Queue
        5. 27.4.5.5 Mixed Dedicated Tx Buffers / Tx FIFO
        6. 27.4.5.6 Mixed Dedicated Tx Buffers / Tx Queue
        7. 27.4.5.7 Transmit Cancellation
        8. 27.4.5.8 Tx Event Handling
      6. 27.4.6 FIFO Acknowledge Handling
      7. 27.4.7 MCAN Message RAM
        1. 27.4.7.1 Message RAM Configuration
        2. 27.4.7.2 Rx Buffer and FIFO Element
        3. 27.4.7.3 Tx Buffer Element
        4. 27.4.7.4 Tx Event FIFO Element
        5. 27.4.7.5 Standard Message ID Filter Element
        6. 27.4.7.6 Extended Message ID Filter Element
      8. 27.4.8 Interrupt Requests
    5. 27.5 CC27xx MCAN Wrapper
    6. 27.6 MCAN Clock Enable
    7. 27.7 Additional Notes
    8. 27.8 CANFD Registers
  30. 28Radio
    1. 28.1  Introduction
    2. 28.2  Block Diagram
    3. 28.3  Overview
      1. 28.3.1 Radio Sub-Domains
      2. 28.3.2 Radio RAMs
      3. 28.3.3 Doorbell (DBELL)
        1. 28.3.3.1 Interrupts
        2. 28.3.3.2 GPIO Control
        3. 28.3.3.3 SYSTIM Interface
    4. 28.4  Radio Usage Model
      1. 28.4.1 CRC and Whitening
    5. 28.5  LRFDDBELL Registers
    6. 28.6  LRFDMDM32 Registers
    7. 28.7  LRFDPBE Registers
    8. 28.8  LRFDPBE32 Registers
    9. 28.9  LRFDRFE Registers
    10. 28.10 LRFDRFE32 Registers
    11. 28.11 LRFDRXF Registers
    12. 28.12 LRFDS2R Registers
    13. 28.13 LRFDTRC Registers
    14. 28.14 LRFDTXF Registers
  31. 29Revision History

2.7.12 SAU Registers

Table 2-470 lists the memory-mapped registers for the SAU registers. All register offset addresses not listed in Table 2-470 should be considered as reserved locations and the register contents should not be modified.

Table 2-470 SAU Registers
OffsetAcronymRegister NameSection
0hSAU_CTRLAllows enabling of the Security Attribution UnitSection 2.7.12.1
4hSAU_TYPEIndicates the number of regions implemented by the Security Attribution UnitSection 2.7.12.2
8hSAU_RNRSelects the region currently accessed by SAU_RBAR and SAU_RLARSection 2.7.12.3
ChSAU_RBARProvides indirect read and write access to the base address of the currently selected SAU regionSection 2.7.12.4
10hSAU_RLARProvides indirect read and write access to the limit address of the currently selected SAU regionSection 2.7.12.5
14hSFSRProvides information about any security related faultsSection 2.7.12.6
18hSFARShows the address of the memory location that caused a Security violationSection 2.7.12.7

Complex bit access types are encoded to fit into small table cells. Table 2-471 shows the codes that are used for access types in this section.

Table 2-471 SAU Access Type Codes
Access TypeCodeDescription
Read Type
RRRead
Write Type
WWWrite
Reset or Default Value
-nValue after reset or the default value

2.7.12.1 SAU_CTRL Register (Offset = 0h) [Reset = 00000000h]

SAU_CTRL is shown in Table 2-472.

Return to the Summary Table.

Allows enabling of the Security Attribution Unit

Table 2-472 SAU_CTRL Register Field Descriptions
BitFieldTypeResetDescription
31-2RES0R0hReserved, RES0
1ALLNSR/W0hWhen SAU_CTRL.ENABLE is 0 this bit controls if the memory is marked as Non-secure or Secure
0ENABLER/W0hEnables the SAU

2.7.12.2 SAU_TYPE Register (Offset = 4h) [Reset = 00000000h]

SAU_TYPE is shown in Table 2-473.

Return to the Summary Table.

Indicates the number of regions implemented by the Security Attribution Unit

Table 2-473 SAU_TYPE Register Field Descriptions
BitFieldTypeResetDescription
31-8RES0RXhReserved, RES0
7-0SREGIONR4hThe number of implemented SAU regions

2.7.12.3 SAU_RNR Register (Offset = 8h) [Reset = 00000000h]

SAU_RNR is shown in Table 2-474.

Return to the Summary Table.

Selects the region currently accessed by SAU_RBAR and SAU_RLAR

Table 2-474 SAU_RNR Register Field Descriptions
BitFieldTypeResetDescription
31-8RES0RXhReserved, RES0
7-0REGIONR/W0hIndicates the SAU region accessed by SAU_RBAR and SAU_RLAR

2.7.12.4 SAU_RBAR Register (Offset = Ch) [Reset = 00000000h]

SAU_RBAR is shown in Table 2-475.

Return to the Summary Table.

Provides indirect read and write access to the base address of the currently selected SAU region

Table 2-475 SAU_RBAR Register Field Descriptions
BitFieldTypeResetDescription
31-5BADDRR/WXhHolds bits [31:5] of the base address for the selected SAU region
4-0RES0R0hReserved, RES0

2.7.12.5 SAU_RLAR Register (Offset = 10h) [Reset = 00000000h]

SAU_RLAR is shown in Table 2-476.

Return to the Summary Table.

Provides indirect read and write access to the limit address of the currently selected SAU region

Table 2-476 SAU_RLAR Register Field Descriptions
BitFieldTypeResetDescription
31-5LADDRR/WXhHolds bits [31:5] of the limit address for the selected SAU region
4-2RES0R0hReserved, RES0
1NSCR/W0hControls whether Non-secure state is permitted to execute an SG instruction from this region
0ENABLER/W0hSAU region enable

2.7.12.6 SFSR Register (Offset = 14h) [Reset = 00000000h]

SFSR is shown in Table 2-477.

Return to the Summary Table.

Provides information about any security related faults

Table 2-477 SFSR Register Field Descriptions
BitFieldTypeResetDescription
31-8RES0RXhReserved, RES0
7LSERRR/W0hSticky flag indicating that an error occurred during lazy state activation or deactivation
6SFARVALIDR/W0hThis bit is set when the SFAR register contains a valid value. As with similar fields, such as BFSR.BFARVALID and MMFSR.MMARVALID, this bit can be cleared by other exceptions, such as BusFault
5LSPERRR/W0hStick flag indicating that an SAU or IDAU violation occurred during the lazy preservation of floating-point state
4INVTRANR/W0hSticky flag indicating that an exception was raised due to a branch that was not flagged as being domain crossing causing a transition from Secure to Non-secure memory
3AUVIOLR/W0hSticky flag indicating that an attempt was made to access parts of the address space that are marked as Secure with NS-Req for the transaction set to Non-secure. This bit is not set if the violation occurred during lazy state preservation. See LSPERR
2INVERR/W0hThis can be caused by EXC_RETURN.DCRS being set to 0 when returning from an exception in the Non-secure state, or by EXC_RETURN.ES being set to 1 when returning from an exception in the Non-secure state
1INVISR/W0hThis bit is set if the integrity signature in an exception stack frame is found to be invalid during the unstacking operation
0INVEPR/W0hThis bit is set if a function call from the Non-secure state or exception targets a non-SG instruction in the Secure state. This bit is also set if the target address is a SG instruction, but there is no matching SAU/IDAU region with the NSC flag set

2.7.12.7 SFAR Register (Offset = 18h) [Reset = 00000000h]

SFAR is shown in Table 2-478.

Return to the Summary Table.

Shows the address of the memory location that caused a Security violation

Table 2-478 SFAR Register Field Descriptions
BitFieldTypeResetDescription
31-0ADDRESSR/W0hThe address of an access that caused a attribution unit violation. This field is only valid when SFSR.SFARVALID is set. This allows the actual flip flops associated with this register to be shared with other fault address registers. If an implementation chooses to share the storage in this way, care must be taken to not leak Secure address information to the Non-secure state. One way of achieving this is to share the SFAR register with the MMFAR_S register, which is not accessible to the Non-secure state