IWRL6843

활성

단일 칩 저전력 고성능 57GHz~64GHz 산업용 mmWave 레이더 센서

제품 상세 정보

Type IC Frequency range 57 - 64 GHz Number of receivers 4 Number of transmitters 3 ADC sampling rate (ksps) 25000 TX power (dBm) 13 Arm CPU Arm Cortex-R5F at 200MHz Hardware accelerators Radar hardware accelerator Edge AI enabled Yes DSP type 1 C66x Interface type 2 CAN-FD, GPIO, I2C, LIN, PWM, QSPI, SPI, UART RAM (kByte) 2000 Operating temperature range (°C) -40 to 105 Security Cryptographic acceleration, Device attestation & anti-counterfeit, Secure firmware & software update, Secure storage, Software IP protection Power supply solution LP87524B-Q1, LP87524J-Q1, LP87524P-Q1, LP87702-Q1 Rating Catalog
Type IC Frequency range 57 - 64 GHz Number of receivers 4 Number of transmitters 3 ADC sampling rate (ksps) 25000 TX power (dBm) 13 Arm CPU Arm Cortex-R5F at 200MHz Hardware accelerators Radar hardware accelerator Edge AI enabled Yes DSP type 1 C66x Interface type 2 CAN-FD, GPIO, I2C, LIN, PWM, QSPI, SPI, UART RAM (kByte) 2000 Operating temperature range (°C) -40 to 105 Security Cryptographic acceleration, Device attestation & anti-counterfeit, Secure firmware & software update, Secure storage, Software IP protection Power supply solution LP87524B-Q1, LP87524J-Q1, LP87524P-Q1, LP87702-Q1 Rating Catalog
FCCSP (ANC) 207 82.81 mm² (9.1 mm × 9.1 mm)
  • FMCW Transceiver
    • Integrated PLL, transmitter, receiver, baseband and ADC
    • 57 - 64GHz coverage with 7GHz continuous bandwidth
    • 4 receive channels and 3 to 4 transmit channels (IWRL6843 with 3 channels and IWRL6844 with 4 channels)
    • 12.5dBm typical output power per TX
    • 12.5dB typical noise figure
    • -90.5dBc/Hz typical phase noise at 1MHz
    • FMCW operation
    • 10MHz IF bandwidth, real-only Rx channels
    • Ultra-accurate chirp engine based on fractional-N PLL
    • Per transmitter binary phase shifter
  • Processing elements
    • Arm R5F core with double precision FPU (200MHz)
    • Hardware Accelerator (HWA 1.2) for FFT, log magnitude, and CFAR operations (200MHz)
    • C66x DSP (450MHz) for processing Radar data
  • Supports multiple low-power modes
    • Idle mode and deep sleep mode
  • Power management
    • 1.8V and 3.3V IO support
    • Built-in LDO network for enhanced PSRR
    • Two power rails for 1.8V IO mode, Three power rails for 3.3V IO mode
  • FCCSP package having 17 x 17 BGA grid, 207 BGA balls; Package size: 9.1mm x 9.1mm
  • Built-in calibration and self-test
    • Built-in Firmware (ROM)
    • Self-Contained on chip calibration system
  • Host Interfaces
    • 3 x UART
    • 2 x CAN-FD
    • 2 x SPI
  • LVDS for data transfer of raw ADC sample capture
  • Other interfaces available to user application
    • QSPI
    • I2C
    • JTAG
    • 8 x GPIOs
    • PWM Interface
    • 4 x GPADCs
  • Device security (on Secure device variants)
    • Programmable embedded hardware security module (HSM)
    • Secure authenticated and encrypted boot support
    • Customer programmable root keys, symmetric keys (256 bit), asymmetric keys (up to RSA-4K or ECC-512) with key revocation capability
    • Cryptographic hardware accelerators: PKA with ECC/RSA, AES (up to 256 bit), SHA (up to 512 bit), TRNG/DRBG and SM2, SM3, SM4(Chinese Crypto Algorithms)
    • Product Cybersecurity Compliance
      • Developed for cybersecurity-relevant applications
      • Documentation will be available to aid cybersecurity system design
  • Internal memory
    • On-Chip RAM - 2.5MBytes (2MBytes for IWRL6843) including

      • R5F TCMA RAM - 512KB
      • R5F TCMB RAM - 256KB
      • DSS L2 RAM - 384KB
      • DSS L3 RAM - 512KB (available only in IWRL6844)
      • DSS L3 Shared RAM - 896KB (can be shared with TCMs)
  • Functional Safety-Compliant Targeted
    • Developed for Functional Safety Applications
    • Documentation will be available to aid functional safety system design
    • Hardware integrity up to SIL 2 targeted as per IEC61508 standard
  • Clock source
    • 40.0MHz crystal for primary clock
    • Supports externally driven clock (Square/Sine) at 40.0MHz
    • 32kHz internal oscillator for low power operations
  • Operating temperature range
    • Junction Temperature Range: –40°C to 105°C
  • FMCW Transceiver
    • Integrated PLL, transmitter, receiver, baseband and ADC
    • 57 - 64GHz coverage with 7GHz continuous bandwidth
    • 4 receive channels and 3 to 4 transmit channels (IWRL6843 with 3 channels and IWRL6844 with 4 channels)
    • 12.5dBm typical output power per TX
    • 12.5dB typical noise figure
    • -90.5dBc/Hz typical phase noise at 1MHz
    • FMCW operation
    • 10MHz IF bandwidth, real-only Rx channels
    • Ultra-accurate chirp engine based on fractional-N PLL
    • Per transmitter binary phase shifter
  • Processing elements
    • Arm R5F core with double precision FPU (200MHz)
    • Hardware Accelerator (HWA 1.2) for FFT, log magnitude, and CFAR operations (200MHz)
    • C66x DSP (450MHz) for processing Radar data
  • Supports multiple low-power modes
    • Idle mode and deep sleep mode
  • Power management
    • 1.8V and 3.3V IO support
    • Built-in LDO network for enhanced PSRR
    • Two power rails for 1.8V IO mode, Three power rails for 3.3V IO mode
  • FCCSP package having 17 x 17 BGA grid, 207 BGA balls; Package size: 9.1mm x 9.1mm
  • Built-in calibration and self-test
    • Built-in Firmware (ROM)
    • Self-Contained on chip calibration system
  • Host Interfaces
    • 3 x UART
    • 2 x CAN-FD
    • 2 x SPI
  • LVDS for data transfer of raw ADC sample capture
  • Other interfaces available to user application
    • QSPI
    • I2C
    • JTAG
    • 8 x GPIOs
    • PWM Interface
    • 4 x GPADCs
  • Device security (on Secure device variants)
    • Programmable embedded hardware security module (HSM)
    • Secure authenticated and encrypted boot support
    • Customer programmable root keys, symmetric keys (256 bit), asymmetric keys (up to RSA-4K or ECC-512) with key revocation capability
    • Cryptographic hardware accelerators: PKA with ECC/RSA, AES (up to 256 bit), SHA (up to 512 bit), TRNG/DRBG and SM2, SM3, SM4(Chinese Crypto Algorithms)
    • Product Cybersecurity Compliance
      • Developed for cybersecurity-relevant applications
      • Documentation will be available to aid cybersecurity system design
  • Internal memory
    • On-Chip RAM - 2.5MBytes (2MBytes for IWRL6843) including

      • R5F TCMA RAM - 512KB
      • R5F TCMB RAM - 256KB
      • DSS L2 RAM - 384KB
      • DSS L3 RAM - 512KB (available only in IWRL6844)
      • DSS L3 Shared RAM - 896KB (can be shared with TCMs)
  • Functional Safety-Compliant Targeted
    • Developed for Functional Safety Applications
    • Documentation will be available to aid functional safety system design
    • Hardware integrity up to SIL 2 targeted as per IEC61508 standard
  • Clock source
    • 40.0MHz crystal for primary clock
    • Supports externally driven clock (Square/Sine) at 40.0MHz
    • 32kHz internal oscillator for low power operations
  • Operating temperature range
    • Junction Temperature Range: –40°C to 105°C

The IWRL684x mmWave Sensor device is TI’s low power and Hardware Security Module (HSM) enabled integrated single chip mmWave sensor based on FMCW radar technology. The device is capable of operation in the 57GHz to 63.9GHz band with 7GHz continuous chirp bandwidth and is designed for various industrial use cases. The device also takes advantage of a low power architecture to enable power-constrained applications. The device is split into the following four switchable power domains:

The IWRL684x is specifically designed to be able to dynamically control the power states of the above-mentioned power domains based on application requirements. The device also features various low-power states and that are achieved by turning off internal IP blocks of the device. IWRL684x device also provides the option of retaining memory during these low power states to retain critical information such as application image and RF profiles across different power modes.

A Hardware Security Module (HSM) is also provisioned in the device (available with secure part variants). The HSM consists of a programmable Arm Cortex-M4 core and the necessary infrastructure to provide a secure zone of operation within the device.

Additionally, the device is built with TI’s low power 45nm RF CMOS process and enables unprecedented levels of integration in an extremely small form factor. IWRL684x is designed for low power, self-monitored, ultra-accurate radar systems in the industrial space for applications like high density people tracking & counting, industrial robots and drones .

The IWRL684x mmWave Sensor device is TI’s low power and Hardware Security Module (HSM) enabled integrated single chip mmWave sensor based on FMCW radar technology. The device is capable of operation in the 57GHz to 63.9GHz band with 7GHz continuous chirp bandwidth and is designed for various industrial use cases. The device also takes advantage of a low power architecture to enable power-constrained applications. The device is split into the following four switchable power domains:

The IWRL684x is specifically designed to be able to dynamically control the power states of the above-mentioned power domains based on application requirements. The device also features various low-power states and that are achieved by turning off internal IP blocks of the device. IWRL684x device also provides the option of retaining memory during these low power states to retain critical information such as application image and RF profiles across different power modes.

A Hardware Security Module (HSM) is also provisioned in the device (available with secure part variants). The HSM consists of a programmable Arm Cortex-M4 core and the necessary infrastructure to provide a secure zone of operation within the device.

Additionally, the device is built with TI’s low power 45nm RF CMOS process and enables unprecedented levels of integration in an extremely small form factor. IWRL684x is designed for low power, self-monitored, ultra-accurate radar systems in the industrial space for applications like high density people tracking & counting, industrial robots and drones .

다운로드 스크립트와 함께 비디오 보기 비디오

기술 자료

검색된 결과가 없습니다. 검색어를 지우고 다시 시도하세요.
7개 모두 보기
상위 문서 유형 직함 형식 옵션 최신 영어 버전 다운로드 날짜
* 데이터 시트 IWRL6843/IWRL6844 Single-Chip 57 to 64GHz Industrial Radar Sensor datasheet (Rev. A) PDF | HTML 2025. 12. 16
* 사용 설명서 xWRL68xx Technical Reference Manual (Rev. A) 2026. 1. 7
* 정오표 IWRL6843/IWRL6844 Device Errata (Rev. A) PDF | HTML 2025. 12. 15
Application brief Understanding Range and Angular Resolution in mmWave Radar Devices (Rev. A) PDF | HTML 2026. 1. 5
Product overview The IWRL6844: Advancing 60GHz Radar Sensing for Factory and Building Automation PDF | HTML 2025. 5. 14
애플리케이션 노트 Calibrations in TI Low-Power mmWave Radar Sensors (Rev. B) PDF | HTML 2025. 2. 3
Application brief Understanding Artificial Intelligence and Machine Learning in Radar Applications PDF | HTML 2024. 12. 4

설계 및 개발

추가 조건 또는 필수 리소스는 사용 가능한 경우 아래 제목을 클릭하여 세부 정보 페이지를 확인하세요.

평가 보드

IWRL6844EVM — IWRL6844 평가 모듈

텍사스 인스트루먼트의 xWRL6844EVM은 사용이 간편한 xWRL6844 mmWave 레이더 센서용 평가 모듈입니다. xWRL6844EVM은 독립 작동 방식은 물론, DCA1000EVM과 직접 연결하여 원시 ADC 캡처 및 신호 처리 개발도 지원합니다. 이 EVM에는 온칩 DSP, 하드웨어 액셀러레이터와 저전력 ARM® Cortex® - R5F 컨트롤러용 소프트웨어 개발을 시작하는 데 필요한 모든 것이 포함되어 있습니다. 또한 EVM에는 온보드 버튼, 간단한 사용자 인터페이스의 빠른 통합을 위한 LED와 프로그래밍 및 디버깅을 (...)
사용 설명서: PDF | HTML
지원되는 제품 및 하드웨어
재고 있음
제한:
??asset.out-of-stock-ti_ko_KR??
이용할 수 없음
IDE, 구성, 컴파일러 또는 디버거

CCSTUDIO — Code Composer Studio integrated development environment (IDE)

CCStudio™ IDE is part of TI's extensive CCStudio™ development ecosystem and is an integrated development environment for TI's microcontrollers, processors, wireless connectivity devices, and radar sensors. CCStudio IDE is available as desktop or cloud-based applications. The cloud version (...)

지원되는 제품 및 하드웨어
IDE, 구성, 컴파일러 또는 디버거

EDGE-AI-STUDIO — Edge AI Studio

Edge AI Studio는 TI 프로세서, 마이크로컨트롤러, 레이더 센서의 에지 AI 개발을 가속화하기 위해 설계된 그래픽 및 명령줄 툴 모음입니다. TI Model Zoo의 모델을 활용해 개념 증명을 개발하든,
자체 모델을 활용하든, Edge AI Studio는 필요한 모든 툴을 제공합니다.

Edge AI Studio 그래픽 사용자 인터페이스는 라이브 개발 플랫폼에 배포할 모델을 교육 및 컴파일하고, 데이터를 수집하고 데이터에 주석을 추가하기 위한 완전 통합 솔루션을 제공합니다. TI Model Zoo에서 다양한 사전 학습된 (...)

지원되는 제품 및 하드웨어
IDE, 구성, 컴파일러 또는 디버거

EDGE-AI-STUDIO-MCU — Edge AI Studio for Microcontrollers

Edge AI Studio는 TI 프로세서, 마이크로컨트롤러, 레이더 센서의 에지 AI 개발을 가속화하기 위해 설계된 그래픽 및 명령줄 툴 모음입니다. TI Model Zoo의 모델을 활용해 개념 증명을 개발하든,
자체 모델을 활용하든, Edge AI Studio는 필요한 모든 툴을 제공합니다.

Edge AI Studio 그래픽 사용자 인터페이스는 라이브 개발 플랫폼에 배포할 모델을 교육 및 컴파일하고, 데이터를 수집하고 데이터에 주석을 추가하기 위한 완전 통합 솔루션을 제공합니다. TI Model Zoo에서 다양한 사전 학습된 (...)

지원되는 제품 및 하드웨어
온라인 교육

RADAR-ACADEMY — mmWave Radar Academy

The Radar Academy is a documentation package intended to provide educational resources related to mmWave radar technology
지원되는 제품 및 하드웨어
시작하기

TI-DEVELOPER-ZONE — Start embedded development on your desktop or in the cloud

From evaluation to deployment the TI Developer Zone provides a comprehensive range of software, tools and training to ensure that you have everything you need for each stage of the development process.
지원되는 제품 및 하드웨어
소프트웨어 프로그래밍 도구

UNIFLASH — UniFlash for most TI microcontrollers (MCUs) and mmWave sensors

UniFlash는 TI의 광범위한 CCStudio™ 개발 에코시스템의 일부로, TI 마이크로컨트롤러 및 무선 연결 장치의 온칩 플래시와 TI 프로세서의 온보드 플래시를 프로그래밍하기 위한 소프트웨어 도구입니다. UniFlash는 그래픽 및 명령줄 인터페이스를 모두 제공하며, 데스크톱 또는 클라우드 환경에서 실행할 수 있습니다.

UniFlash는 CCStudio 개발자 영역의 클라우드에서 실행하거나 Windows®, Linux®, macOS® 컴퓨터에서 다운로드해 사용할 수 있습니다.

macOS는 mmWave, AMx, K2G 및 (...)

지원되는 제품 및 하드웨어
지원 소프트웨어

RADAR-TOOLBOX — Radar evaluation and development support package with example projects, documentation and tools

The Radar Toolbox is a collection of demos, software tools, and documentation designed to assist in the evaluation of TI Radar Devices
지원되는 제품 및 하드웨어
패키지 CAD 기호, 풋프린트 및 3D 모델
FCCSP (ANC) 207 Ultra Librarian

주문 및 품질

권장 제품에는 본 TI 제품과 관련된 매개 변수, 평가 모듈 또는 레퍼런스 디자인이 있을 수 있습니다.

지원 및 교육

TI 엔지니어의 기술 지원을 받을 수 있는 TI E2E™ 포럼

콘텐츠는 TI 및 커뮤니티 기고자에 의해 "있는 그대로" 제공되며 TI의 사양으로 간주되지 않습니다. 사용 약관을 참조하십시오.

품질, 패키징, TI에서 주문하는 데 대한 질문이 있다면 TI 지원을 방문하세요. ​​​​​​​​​​​​​​

동영상