Top

Product details

Parameters

Resolution (Bits) 16 DAC channels 1 Interface type SPI Output type Buffered Current, Buffered Voltage Settling time (µs) 10 Features Current Output, Low Power Reference: type Ext, Int Architecture String Rating Catalog Output range (Max) (mA/V) 24 Output range (Min) (mA/V) 0 Operating temperature range (C) -40 to 125 open-in-new Find other Precision DACs (<=10MSPS)

Package | Pins | Size

HTSSOP (PWP) 24 34 mm² 7.7 x 4.4 VQFN (RHA) 40 36 mm² 6 x 6 open-in-new Find other Precision DACs (<=10MSPS)

Features

  • Current Output: 4 mA to 20 mA;
    0 mA to 20 mA; 0 mA to 24 mA
  • Voltage Output:
    • 0 V to 5 V; 0 V to 10 V; ±5 V; ±10 V
    • 0 V to 5.5 V; 0 V to 11 V; ±5.5 V; ±11 V
      (10% Over Range)
  • ±0.1% FSR Total Unadjusted Error (TUE) Maximum
  • DNL: ±1 LSB Maximum
  • Simultaneous Voltage and Current Output
  • Internal 5-V Reference (10 ppm/°C, Maximum)
  • Internal 4.6-V Power-Supply Output
  • Reliability Features:
    • CRC Check and Watchdog Timer
    • Thermal Alarm
    • Open Alarm, Short Current Limit
  • Wide Temperature Range: –40°C to 125°C
  • 6-mm × 6-mm 40-Pin VQFN and 24-Pin HTSSOP Packages

All trademarks are the property of their respective owners.

open-in-new Find other Precision DACs (<=10MSPS)

Description

The DAC7760 and DAC8760 are low-cost, precision, fully-integrated, 12-bit and 16-bit digital-to-analog converters (DACs) designed to meet the requirements of industrial process-control applications. These devices can be programmed as a current output with a range of 4 mA to 20 mA, 0 mA to 20 mA, or 0 mA to 24 mA; or as a voltage output with a range of 0 V to 5 V, 0 V to 10 V, ±5 V, or
±10 V with a 10% overrange (0 V to 5.5 V, 0 V to
11 V, ±5.5 V, or ±11 V). Both current and voltage outputs can be simultaneously enabled while being controlled by a single data register.

These devices include a power-on-reset function to ensure powering up in a known state (both IOUT and VOUT are disabled and in a Hi-Z state). The CLR and CLR-SEL pins set the voltage outputs to zero-scale or midscale, and the current output to the low end of the range, if the output is enabled. Zero and gain registers can be programmed to digitally calibrate the device in the end system. The output slew rate is also programmable by register. These devices can superimpose an external HART® signal on the current output and can operate with either a single 10-V to 36-V supply, or dual supplies of up to ±18 V. All versions are available in both 6-mm ×
6-mm 40-pin VQFN and 24-pin HTSSOP packages.

open-in-new Find other Precision DACs (<=10MSPS)
Download

Technical documentation

= Top documentation for this product selected by TI
No results found. Please clear your search and try again. View all 12
Type Title Date
* Datasheet DACx760 Single-Channel, 12- and 16-Bit Programmable Current and Voltage Output Digital-to-Analog Converters for 4-mA to 20-mA Current Loop Applications datasheet (Rev. C) Jan. 04, 2018
Application notes Thermal Management to Increase Density in PLC AO Modules Jun. 12, 2018
Technical articles Input Isolation for 3-wire Analog Outputs Jun. 15, 2015
Technical articles A new feather in the cap – new MSP430 industrial series microcontrollers are here! Nov. 05, 2014
Application notes Analog Applications Journal 4Q 2014 Oct. 24, 2014
Application notes SPICE models for Precision DACs Oct. 24, 2014
Technical articles Industrial DACs: How to design universal analog outputs Sep. 24, 2014
Technical articles Industrial DACs: Protecting 3-wire analog outputs Aug. 12, 2014
Application notes Combined Voltage and Current Output with the DACx760 Jul. 24, 2014
User guides DACx760EMC-EVM User's Guide Apr. 24, 2014
Application notes Implementing HART™ Communication With the DAC8760 Family Jan. 16, 2014
User guides DACx760EVM and DACx750EVM User's Guide (Rev. A) Nov. 21, 2013

Design & development

For additional terms or required resources, click any title below to view the detail page where available.

Hardware development

EVALUATION BOARDS Download
document-generic User guide
75
Description

The DAC8760EMC-EVM (EMC enhanced evaluation module) provides an easy to use platform for evaluation of the performance and operating characteristics of the DAC8760 (16-bit, Voltage Output & Current Output DAC) in harsh industrial environments. The EVM is a complete evaluation kit that includes a (...)

Features
  • Protection circuitry against IEC61000-4 ESD, EFT, CI, and RI test standards
  • 4kV Galvanic Isolation between host MCU and DAC8760
  • LabVIEW™ based PC Evaluation Software
EVALUATION BOARDS Download
document-generic User guide
149
Description

The DAC8760EVM (evaluation module) provides an easy to use platform for evaluation of the performance and operating characteristics of the DAC8760 (16-bit, Voltage Output  & Current Output DAC). The EVM is a complete evaluation kit that includes a USB-based motherboard called the (...)

Features
  • Test point access to all analog and digital signals
  •  Jumper-selectable hardware configurations
  •  LabVIEW™ based PC Evaluation Software

Software development

SUPPORT SOFTWARE Download
SBOC433B.ZIP (208485 KB)

Design tools & simulation

SIMULATION MODELS Download
SBAM177.ZIP (50 KB) - IBIS Model
SIMULATION TOOLS Download
PSpice® for TI design and simulation tool
PSPICE-FOR-TI — PSpice® for TI is a design and simulation environment that helps evaluate functionality of analog circuits. This full-featured, design and simulation suite uses an analog analysis engine from Cadence®. Available at no cost, PSpice for TI includes one of the largest model libraries in the (...)
Features
  • Leverages Cadence PSpice Technology
  • Preinstalled library with a suite of digital models to enable worst-case timing analysis
  • Dynamic updates ensure you have access to most current device models
  • Optimized for simulation speed without loss of accuracy
  • Supports simultaneous analysis of multiple products
  • (...)
SIMULATION TOOLS Download
SPICE-based analog simulation program
TINA-TI TINA-TI provides all the conventional DC, transient and frequency domain analysis of SPICE and much more. TINA has extensive post-processing capability that allows you to format results the way you want them. Virtual instruments allow you to select input waveforms and probe circuit nodes voltages (...)
document-generic User guide
CALCULATION TOOLS Download
Analog engineer's calculator
ANALOG-ENGINEER-CALC — The Analog Engineer’s Calculator is designed to speed up many of the repetitive calculations that analog circuit design engineers use on a regular basis. This PC-based tool provides a graphical interface with a list of various common calculations ranging from setting op-amp gain with feedback (...)
Features
  • Expedites circuit design with analog-to-digital converters (ADCs) and digital-to-analog converters (DACs)
    • Noise calculations
    • Common unit translation
  • Solves common amplifier circuit design problems
    • Gain selections using standard resistors
    • Filter configurations
    • Total noise for common amplifier configurations
  • (...)

Reference designs

REFERENCE DESIGNS Download
Multi-Channel Analog Output Module With Multiplexed Single-Channel DAC for PLCs Reference Design
TIDA-00760 This reference design helps achieve low-cost, high-speed, small form-factor and high resolution for programmable logic controller (PLC) analog output module designs based on sequentially multiplexed sample and hold buffers.
document-generic Schematic document-generic User guide
REFERENCE DESIGNS Download
Combined Voltage/Current Output with Surge Protection Reference Design
TIDA-00559 The TIDA-00559 TI Design provides a universal analog output (AO) for industrial sensors and transmitters. It is based on a 16-Bit DAC and uses a single output. This common output is user configurable for 0 to 10-V or for 4 to 20-mA. Usage in harsh industrial environment is addressed by a dedicated (...)
document-generic Schematic document-generic User guide
REFERENCE DESIGNS Download
16-Bit Analog Mixed Input and Output Module for Programmable Logic Controller (PLC) Reference Design
TIDA-00170 The TIDA-00170 is a reference design for industrial control Analog Mixed Input Output Modules. The design implements four channel analog input & two channel analog output. The analog input channels can measure all standard industrial voltages up to ±10V and current inputs up to 24mA. The (...)
document-generic Schematic document-generic User guide
REFERENCE DESIGNS Download
16-Bit Analog Output Module Reference Design for Programmable Logic Controllers (PLC)
TIDA-00118 This reference design provides a complete 4-channel, 16-bit analog output module design for Programmable Logic Controllers (PLCs). It is designed and fully tested to meet IEC61000-4 EMC and surge requirements for industrial automation systems. The small form-factor design implements four 16-bit (...)
document-generic Schematic document-generic User guide
REFERENCE DESIGNS Download
Adaptive Power Supply for PLC Analog Output Module with Output Channel Protection
TIDA-00231 TIDA-00231 is a reference design for an industrial Programmable Logic Controller (PLC) analog output module. The design provides a unique power saving solution for a digital-to-analog converter (DAC)-based analog current output module with an adaptive power supply. This adaptive power supply (...)
document-generic Schematic document-generic User guide
REFERENCE DESIGNS Download
Analog Input, Output and Relay Drive Output Module for Smart Grid IEDs Reference Design
TIDA-00310 This reference design showcases a flexible Analog IO solution for Smart Grid devices like Protection Relays and RTUs that also need to communicate with other devices on the grid that use the analog IO such as voltage (5V to 10V DC) or current (4-20mA). This solution enables both types of IO as well (...)
document-generic Schematic document-generic User guide
REFERENCE DESIGNS Download
Combined Voltage and Current Output Terminal for Analog Outputs (AO) in Industrial Applications
TIPD119 This TI Verified Reference Design implements a combined voltage and current output terminal for analog outputs in industrial applications.  The DAC8760 combined with the OPA192 create a combined voltage and current output that allows for a single two-terminal output connector for both the voltage and (...)
document-generic Schematic document-generic User guide
REFERENCE DESIGNS Download
Single-Channel Industrial Voltage & Current Output Driver, Isolated, EMC/EMI Tested Reference Design
TIPD153 This TI CerTIfied Reference Design implements a isolated single-channel industrial voltage and current output module using the DAC8760 and ISO7641.  The circuit features a digitally controlled voltage or current output that produces the standard outputs of 0-20mA, 0-24mA, 4-20mA, 0-5V, +/-5V (...)
document-generic Schematic document-generic User guide

CAD/CAE symbols

Package Pins Download
HTSSOP (PWP) 24 View options
VQFN (RHA) 40 View options

Ordering & quality

Support & training

TI E2E™ forums with technical support from TI engineers

Content is provided "as is" by TI and community contributors and does not constitute TI specifications. See terms of use.

If you have questions about quality, packaging or ordering TI products, see TI support. ​​​​​​​​​​​​​​

Videos

Related videos