25 MHz MCU with 32KB Flash, 4KB SRAM, 10-bit ADC, Comparator, DMA, UART/SPI/I2C, USB, HW Multiplier
Product details
Parameters
Package | Pins | Size
Features
- Low supply-voltage range:
3.6 V down to 1.8 V - Ultra-low power consumption
- Active mode (AM)
All system clocks active- 195 µA/MHz at 8 MHz, 3 V, flash program execution (typical)
- 115 µA/MHz at 8 MHz, 3 V, RAM program execution (typical)
- Standby mode (LPM3)
- Real-time clock (RTC) with crystal, watchdog, and supply supervisor operational, full RAM retention, fast wakeup:
1.9 µA at 2.2 V, 2.1 µA at 3 V (typical) - Low-power oscillator (VLO), general-purpose counter, watchdog, and supply supervisor operational, full RAM retention, fast wakeup:
1.4 µA at 3 V (typical)
- Real-time clock (RTC) with crystal, watchdog, and supply supervisor operational, full RAM retention, fast wakeup:
- Off mode (LPM4)
Full RAM retention, supply supervisor operational, fast wakeup:
1.1 µA at 3 V (typical) - Shutdown mode (LPM4.5)
0.18 µA at 3 V (typical)
- Active mode (AM)
- Wake up from standby in less than 5 µs
- 16-bit RISC architecture, extended memory, up to 25-MHz system clock
- Flexible power-management system
- Fully integrated LDO with programmable regulated core supply voltage
- Supply voltage supervision, monitoring, and brownout
- Unified clock system
- FLL control loop for frequency stabilization
- Low-power low-frequency internal clock source (VLO)
- Low-frequency trimmed internal reference source (REFO)
- 32-kHz watch crystals (XT1)
- High-frequency crystals up to 32 MHz (XT2)
- 16-bit Timer TA0, Timer_A with five capture/compare registers
- 16-bit Timer TA1, Timer_A with three capture/compare registers
- 16-bit Timer TA2, Timer_A with three capture/compare registers
- 16-bit Timer TB0, Timer_B with seven capture/compare shadow registers
- Two universal serial communication interfaces (USCIs)
- USCI_A0 and USCI_A1 each support:
- Enhanced UART with automatic baud-rate detection
- IrDA encoder and decoder
- Synchronous SPI
- USCI_B0 and USCI_B1 each support:
- I2C
- Synchronous SPI
- USCI_A0 and USCI_A1 each support:
- Full-speed universal serial bus (USB)
- Integrated USB-PHY
- Integrated 3.3-V and 1.8-V USB power system
- Integrated USB-PLL
- Eight input and eight output endpoints
- 10-bit analog-to-digital converter (ADC) with window comparator
- Comparator
- Hardware multiplier supports 32-bit operations
- Serial onboard programming, no external programming voltage needed
- Three-channel internal DMA
- Basic timer with RTC feature
- Device Comparison summarizes the available family members
All trademarks are the property of their respective owners.
Description
The TI MSP family of ultra-low-power microcontrollers consists of several devices featuring different sets of peripherals targeted for various applications. The architecture, combined with extensive low-power modes, is optimized to achieve extended battery life in portable measurement applications. The device features a powerful 16-bit RISC CPU, 16-bit registers, and constant generators that contribute to maximum code efficiency. The digitally controlled oscillator (DCO) allows the device to wake up from low-power modes to active mode in less than 5 µs.
The MSP430F5510, MSP430F5509, and MSP430F5508 devices are microcontroller configurations with integrated USB and PHY supporting USB 2.0, four 16-bit timers, a high-performance 10-bit ADC, two USCIs (1), a hardware multiplier, DMA, an RTC module with alarm capabilities, and 31 or 47 I/O pins.
The MSP430F5507, MSP430F5506, MSP430F5505, and MSP430F5504 devices are microcontroller configurations with integrated USB and PHY supporting USB 2.0, four 16-bit timers, a high-performance 10-bit ADC, one USCI, a hardware multiplier, DMA, an RTC module with alarm capabilities, and 31 I/O pins.
The MSP430F5503, MSP430F5502, MSP430F5501, and MSP430F5500 devices include all of the MSP430F5507, MSP430F5506, MSP430F5505, and MSP430F5504 peripherals, except that they have a comparator instead of the 10-bit ADC.
Typical applications include analog and digital sensor systems and data loggers that require connectivity to various USB hosts.
For complete module descriptions, see the MSP430F5xx and MSP430F6xx Family Users Guide.
(1)In the 48-pin packages, the USCI functions that are pinned out are limited to what the user configures on port 4 with the port mapping controller. It may not be possible to bring out all functions simultaneously.
Important information
We are currently planning the next generation of this product. The new part will leverage a laminate BGA package that we call nFBGA. This package offers datasheet-equivalent electrical performance. It is also board layout/footprint equivalent to MicroStar. For more details, please reference this application note.
Technical documentation
Design & development
For additional terms or required resources, click any title below to view the detail page where available.Hardware development
Description
The DRV52510-Q1 evaluation module (EVM) allows a designer to driver to assess the device alone or connected to target actuators such as a solenoid to easily and quickly evaluate performance of the driver or the actuator in use conditions.
Features
- High output current capable of 3A peak
- Integrated diagnostics
- Analog input
- I2C communication of device status and system conditions
- Wide operating voltage range of 4.5 V – 18V
Description
Features
- High output current capable of 8A peak
- Integrated fault protect modes
- Analog input
- Wide operating voltage range of 4.5 V – 18V
Description
The DRV2700EVM is an evaluation module for the DRV2700. The DRV2700 is intended for high voltage piezo applications typically used in Industrial Applications. The differential 200Vpp output capability as well as the 100V single ended output can be evaluated using this EVM. The available pin (...)
Features
- 5V input to +/-100V Differential Output
- Single ended and differential input modes
- Multiple boost voltage settings
- Easily powered through USB or external Power Supply
- Breakout for usage as a boost converter
Description
The EVM430-CAPMINI is an easy-to-use evaluation board for the MSP430FR2512 capacitive-touch-sensing microcontroller. It demonstrates the key features of CapTIvate technology such as ultra-low power and ease of use. The onboard CapTIvate HID bridge tool supports touch online tuning with CapTIvate (...)
Features
- Features the ultra-low-power MSP430FR2512 capacitive sensing MCU
- Four Capacitive touch buttons
- On-board speaker for outputting sound
- On-board HID bridge for communicating with CapTIvate Design Center on PC
Description
The Educational BoosterPack MKII offers a high level of integration for developers to quickly prototype complete solutions. Various analog and digital inputs/outputs are at your disposal including an analog joystick, environmental and motion sensors, RGB LED, microphone, buzzer (...)
Features
- TI OPT3001 Light Sensor
- TI TMP006 Temperature Sensor
- Servo Motor Connector
- 3-Axis Accelerometer
- User Push Buttons
- RGB Multi-color LED
- Buzzer
- 40-pin Stackable BoosterPack Connector
- Color TFT LCD Display
- Microphone
- 2-Axis Joystick with Pushbutton
Description
The MSP-TS430RGC64USB is a standalone 64-pin ZIF socket target board used to program and debug the MSP430 MCU in-system through the JTAG interface or the Spy Bi-Wire (2-wire JTAG) protocol.
Device Support: The MSP-TS430RGCUSB development board supports MSP430F550x, MSP430F551x and MSP430F552x MCUs in (...)
Features
- Development board (MSP-TS430RGC64USB) MSP-TS430RGC64USB with a 64-pin ZIF socket fitting MSP430 derivatives in 64-pin QFN (RGC) packages includes an LED indicator, JTAG adapter, and header pin-outs for prototyping.
- Supports all debugging interfaces using a standard 14-pin JTAG header such as the (...)
Description
The MSP-FET is a powerful emulation development tool – often called a debug probe – which allows users to quickly begin development on MSP low-power microcontrollers (MCU).
It supports programming and real-time debugging over both JTAG and SBW interfaces. Furthermore, the MSP-FET also provides a (...)
Features
- USB debugging interface to connect any MSP430 MCU to a computer for real-time, in-system programming and debugging
- Enables EnergyTrace™ technology for energy measurement and debugging on all MSP430 and MSP432 devices in the Code Composer Studio and IAR Embedded Workbench development environments
- (...)
Description
The MSP Gang Programmer (MSP-GANG) is a MSP430™/MSP432™ device programmer that can program up to eight identical MSP430/MSP432 Flash or FRAM devices at the same time. It connects to a host PC using a standard RS-232 or USB connection and provides flexible programming options that allow (...)
Features
- Quickly and reliably program Flash or FRAM-based MSP devices via RS-232 or USB interface
- Several programming modes:
- Interactive Mode – Programming while connected to PC using the MSP GANG Programmer GUI
- Program from Image – An image can be stored, which contains configuration options and code (...)
Software development
This complete collection of (...)
Features
- Collection of MSP design resources
- Available within CCS, as a standalone executable, or as part of TI’s new Cloud-based tools
- Auto-updates through the web
- Sleek & intuitive GUI for browsing content
- Features the MSP Driver Library
- Automatic filtering of content using a unique 2-pane view
Features
- MSP430G23xx
- MSP430G24xx
- MSP430G25xx
- MSP430G2x44
- MSP430G2x55
- MSP430F5xx
- MSP430FR2433
- MSP430FR25xx
- MSP430FR26xx
- MSP430FR57xx
Note: This software is available as part of MSPWare. If you have downloaded and (...)
Features
- MSP430 API Code Stacks - Contains all necessary API's and examples to get started with USB development, using the CDC (Communications Device Class), HID (Human Interface Device) and MSC (Mass Storage Class) classes. The USB API also supports composite devices where a single physical device contains (...)
Features
- Free license and royalty-free use
- Simplify and accelerate development of applications
- Easy-to-maintain code
Features
- Up to 26x higher performance when executing floating point scalar math functions
- Remains in low power modes longer due to the increased performance
- Free and easy to use – now integrated in CCS and IAR
Code Composer Studio is an integrated development environment (IDE) that supports TI's Microcontroller and Embedded Processors portfolio. Code Composer Studio comprises a suite of tools used to develop and debug embedded applications. It includes an optimizing C/C++ compiler, source code editor (...)
Features
- Simple & easy-to-use code editor & compiler with built-in Serial Monitor/terminal
- Features a robust framework of intuitive functional APIs for controlling microcontroller peripherals (i.e. digitalRead, digitalWrite, Serial.print, etc)
- Support for various TI embedded devices (MSP430, TM4C, CC3200 (...)
As most developers know, it is difficult to (...)
Features
- Current measurement is enabled for all MSP430 MCUs, MSP432 MCUs and connectivity devices
- Tracing of CPU states is available on selected MSP430 MCUs, MSP432 MCUs, CC13x2 wireless MCUs and CC26x2 wireless MCUs
- Tracing of peripheral states is also available on selected MSP430 MCUs, CC13x2 (...)
CCS Uniflash is a standalone tool used to (...)
Design tools & simulation
Reference designs
Design files
-
download TIDA-00856 BOM.pdf (141KB) -
download TIDA-00856 Assembly Drawing.pdf (186KB) -
download TIDA-00856 PCB.pdf (1097KB) -
download TIDA-00856 CAD Files.zip (668KB) -
download TIDA-00856 Gerber.zip (437KB)
Design files
-
download TIDA-00609 BOM.pdf (125KB) -
download TIDA-00609 Assembly Drawing.pdf (1219KB) -
download TIDA-00609 PCB.pdf (2187KB) -
download TIDA-00609 CAD Files.zip (24452KB) -
download TIDA-00609 Gerber.zip (7534KB)
Design files
-
download PMP5722 BOM.pdf (17KB) -
download PMP5722 Assembly Drawing.pdf (34KB) -
download PMP5722 CAD Files.zip (366KB) -
download PMP5722 Gerber.zip (274KB)
CAD/CAE symbols
Package | Pins | Download |
---|---|---|
LQFP (PT) | 48 | View options |
NFBGA (ZXH) | 80 | View options |
VQFN (RGC) | 64 | View options |
VQFN (RGZ) | 48 | View options |
Ordering & quality
- RoHS
- REACH
- Device marking
- Lead finish/Ball material
- MSL rating/Peak reflow
- MTBF/FIT estimates
- Material content
- Qualification summary
- Ongoing reliability monitoring
Support & training
TI E2E™ forums with technical support from TI engineers
Content is provided "as is" by TI and community contributors and does not constitute TI specifications. See terms of use.
If you have questions about quality, packaging or ordering TI products, see TI support.