MSP430F6724A

• Low Supply-Voltage Range:
  3.6 V Down to 1.8 V
• Ultra-Low Power Consumption
  • Active Mode (AM):
    All System Clocks Active
    265 µA/MHz at 8 MHz, 3.0 V, Flash Program Execution (Typical)
    140 µA/MHz at 8 MHz, 3.0 V, RAM Program Execution (Typical)
  • Standby Mode (LPM3):
    Real-Time Clock (RTC) With Crystal, Watchdog, and Supply Supervisor Operational, Full RAM Retention, Fast Wake up:
    1.7 µA at 2.2 V, 2.5 µA at 3.0 V (Typical)
  • Off Mode (LPM4):
    Full RAM Retention, Supply Supervisor Operational, Fast Wake up:
    1.6 µA at 3.0 V (Typical)
  • Shutdown RTC Mode (LPM3.5):
    Shutdown Mode, Active RTC With Crystal:
    1.24 µA at 3.0 V (Typical)
  • Shutdown Mode (LPM4.5):
    0.78 µA at 3.0 V (Typical)
• Wake up From Standby Mode in 3 µs (Typical)
• 16-Bit RISC Architecture, Extended Memory, up to 25-MHz System Clock
• Flexible Power-Management System
  • Fully Integrated LDO With Programmable Regulated Core Supply Voltage
  • Supply Voltage Supervision, Monitoring, and Brownout
  • System Operation From up to Two Auxiliary Power Supplies
• Unified Clock System
  • FLL Control Loop for Frequency Stabilization
  • Low-Power Low-Frequency Internal Clock Source (VLO)
  • Low-Frequency Trimmed Internal Reference Source (REFO)
  • 32-kHz Crystals (XT1)
• One 16-Bit Timer With Three Capture/Compare Registers
• Three 16-Bit Timers With Two Capture/Compare Registers Each
• Enhanced Universal Serial Communication Interfaces (eUSCIs)
  • eUSCI_A0, eUSCI_A1, and eUSCI_A2
    • Enhanced UART Supports Automatic Baud-Rate Detection
    • IrDA Encoder and Decoder
    • Synchronous SPI
  • eUSCI_B0
    • I²C With Multiple Slave Addressing
    • Synchronous SPI
• Password-Protected RTC With Crystal Offset Calibration and Temperature Compensation
• Separate Voltage Supply for Backup Subsystem
  • 32-kHz Low-Frequency Oscillator (XT1)
  • Real-Time Clock
  • Backup Memory (4 × 16 Bits)
• Three 24-Bit Sigma-Delta Analog-to-Digital Converters (ADCs) With Differential PGA Inputs
• Integrated LCD Driver With Contrast Control for up to 320 Segments in 8-Mux Mode
• Hardware Multiplier Supports 32-Bit Operations
• 10-Bit 200-ksps ADC
  • Internal Reference
  • Sample-and-Hold, Autoscan Feature
  • Up to Six External Channels and Two Internal Channels, Including Temperature Sensor
• Three-Channel Internal DMA
• Serial Onboard Programming, No External Programming Voltage Needed
• Device Comparison Summarizes the Available Family Members
• Available in 100-Pin and 80-Pin LQFP Packages
• Single-Phase Electronic Watt-Hour Meter Development Tool (Also See Tools and Software)
  • EVM430-F6736 - MSP430F6736 EVM for Metering
  • Energy Measurement Design Center for MSP430™ MCUs

All trademarks are the property of their respective owners.

The TI MSP family of ultra-low-power microcontrollers consists of several devices featuring different sets of peripherals targeted for various applications. The architecture, combined with extensive low-power modes, is optimized to achieve extended battery life in portable measurement applications. The device features a powerful 16-bit RISC CPU, 16-bit registers, and constant generators that contribute to maximum code efficiency. The DCO allows the device to wake up from low-power modes to active mode in 3 µs (typical).

The MSP430F673xA and MSP430F672xA devices are microcontrollers with high-performance 24-bit sigma-delta ADCs (three ADCs in MSP430F673xA and two ADCs in MSP430F672xA), a 10-bit ADC, four eUSCIs (three eUSCI_A modules and one eUSCI_B module), four 16-bit timers, a hardware multiplier, a DMA module, an RTC module with alarm capabilities, an LCD driver with integrated contrast control, an auxiliary supply system, and up to 72 I/O pins in the 100‑pin devices and 52 I/O pins in the 80‑pin devices.

For complete module descriptions, see the MSP430F5xx and MSP430F6xx Family User’s Guide.