MSP430F2617

ACTIVE

16 MHz MCU with 92KB FLASH, 8KB SRAM, 12-bit ADC, Dual 12-bit DAC, I2C/SPI/UART, HW Multiplier, DMA

Top

Product details

Parameters

Non-volatile memory (kB) 92 RAM (KB) 8 ADC 12-bit SAR ADC: channels (#) 8 GPIO pins (#) 48 I2C 2 SPI 2 UART 2 Comparator channels (#) 8 Timers - 16-bit 2 Bootloader (BSL) UART Special I/O Operating temperature range (C) -40 to 105 Rating Catalog open-in-new Find other MSP430 ultra-low-power MCUs

Package | Pins | Size

LQFP (PM) 64 100 mm² 10 x 10 LQFP (PN) 80 196 mm² 14 x 14 NFBGA (ZCA) 113 49 mm² 7 x 7 open-in-new Find other MSP430 ultra-low-power MCUs

Features

  • Low supply voltage range: 1.8 V to 3.6 V
  • Ultra-low power consumption
    • Active mode: 365 µA at 1 MHz, 2.2 V
    • Standby mode (VLO): 0.5 µA
    • Off mode (RAM retention): 0.1 µA
  • Wake up from standby mode in less than 1 µs
  • 16-bit RISC architecture, 62.5-ns instruction cycle time
  • Three-channel internal DMA (MSP430F261x only)
  • 12-bit analog-to-digital converter (ADC) with internal reference, sample-and-hold, and autoscan feature
  • Dual 12-bit digital-to-analog converters (DACs) with synchronization (MSP430F261x only)
  • 16-bit Timer_A with three capture/compare registers
  • 16-bit Timer_B with seven capture/compare registers with shadow registers
  • On-chip comparator
  • Four universal serial communication interfaces (USCIs)
    • USCI_A0 and USCI_A1
      • Enhanced UART supporting automatic baud-rate detection
      • IrDA encoder and decoder
      • Synchronous SPI
    • USCI_B0 and USCI_B1
      • I2C
      • Synchronous SPI
  • Supply voltage supervisor and monitor with programmable level detection
  • Brownout detector
  • Bootloader (BSL)
  • Serial onboard programming, no external programming voltage needed, programmable code protection by security fuse
  • Family members (also see Device Comparison)
    • MSP430F2416
      • 92KB + 256 bytes flash memory
      • 4KB RAM
    • MSP430F2417
      • 92KB + 256 bytes flash memory
      • 8KB RAM
    • MSP430F2418
      • 116KB + 256 bytes flash memory
      • 8KB RAM
    • MSP430F2419
      • 120KB + 256 bytes flash memory
      • 4KB RAM
    • MSP430F2616
      • 92KB + 256 bytes flash memory
      • 4KB RAM
    • MSP430F2617
      • 92KB + 256 bytes flash memory
      • 8KB RAM
    • MSP430F2618
      • 116KB + 256 bytes flash memory
      • 8KB RAM
    • MSP430F2619
      • 120KB + 256 bytes flash memory
      • 4KB RAM
  • Available in 80-pin quad flat pack (LQFP), 64-pin LQFP, and 113-pin ball grid array (nFBGA)

All trademarks are the property of their respective owners.

open-in-new Find other MSP430 ultra-low-power MCUs

Description

The Texas Instruments MSP430™ family of ultra-low-power microcontrollers consists of several devices featuring different sets of peripherals targeted for various applications. The architecture, combined with five low-power modes is optimized to achieve extended battery life in portable measurement applications. The device features a powerful 16-bit RISC CPU, 16-bit registers, and constant generators that contribute to maximum code efficiency. The calibrated digitally controlled oscillator (DCO) allows wake-up from low-power modes to active mode in less than 1 µs.

The MSP430F261x and MSP430F241x series are microcontroller configurations with two built-in 16-bit timers, a fast 12-bit ADC, a comparator, two 12-bit DACs, four USCI modules, DMA, and up to 64 I/O pins. The MSP430F241x devices are identical to the MSP430F261x devices, with the exception that the DAC12 and the DMA modules are not implemented.

The LQFP-64 package is also available as a nonmagnetic package for medical imaging applications.

For complete module descriptions, see the MSP430F2xx, MSP430G2xx Family User’s Guide.

open-in-new Find other MSP430 ultra-low-power MCUs
Download

Technical documentation

= Top documentation for this product selected by TI
No results found. Please clear your search and try again. View all 37
Type Title Date
* Datasheet MSP430F261x, MSP430F241x Mixed-Signal Microcontrollers datasheet (Rev. L) May 01, 2020
* Errata MSP430F2617 Device Erratasheet (Rev. S) Apr. 21, 2020
* User guides MSP430x2xx Family User's Guide (Rev. J) Jul. 01, 2013
Application notes MSP430 System ESD Troubleshooting Guide Dec. 13, 2019
Application notes ESD Diode Current Specification (Rev. A) Jul. 10, 2019
Application notes Migrating from MSP430 F2xx and G2xx families to MSP430 FR4xx and FR2xx family (Rev. F) Mar. 26, 2019
Application notes Programming a Flash-Based MSP430 MCU Using the JTAG Interface (Rev. H) Mar. 15, 2019
Application notes Interfacing the 3-V MSP430 MCU to 5-V Circuits (Rev. A) Oct. 03, 2018
Application notes Migrating From MSP430F16x MCUs to MSP430F261x MCUs (Rev. B) Sep. 26, 2018
Application notes MSP430 Flash Memory Characteristics (Rev. B) Aug. 24, 2018
Application notes Understanding MSP430 Flash Data Retention (Rev. A) Aug. 24, 2018
Application notes Mixing C and Assembler With MSP430™ MCUs (Rev. A) Aug. 07, 2018
Application notes Using the TPS3619 With MSP430 Microcontrollers (Rev. B) Aug. 06, 2018
Application notes MSP430 LFXT1 Oscillator Accuracy (Rev. A) Aug. 03, 2018
Application notes Efficient Multiplication and Division Using MSP430 MCUs (Rev. A) Jul. 18, 2018
Application notes CRC Implementation with MSP430 MCUs (Rev. A) Jun. 21, 2018
Application notes Implementing An Ultra-Low-Power Keypad Interface With MSP430 MCUs (Rev. A) May 22, 2018
Application notes Li-Ion Battery Charger Solution Using an MSP430™ MCU (Rev. A) May 18, 2018
Application notes Random Number Generation Using MSP430™ MCUs (Rev. A) May 16, 2018
Application notes Wave Digital Filtering Using an MSP430 MCU (Rev. A) May 16, 2018
Application notes Software Coding Techniques for MSP430™ MCUs (Rev. B) Mar. 14, 2018
Application notes MSP430 32-kHz Crystal Oscillators (Rev. D) Jul. 18, 2017
Application notes Migrating from the MSP430F2xx,G2xx Family to the MSP430FR58xx/FR59xx/68xx/69xx (Rev. E) Nov. 03, 2016
Application notes Advanced Debugging Using the Enhanced Emulation Module (EEM) With CCS v6 (Rev. F) Sep. 06, 2016
Application notes General Oversampling of MSP ADCs for Higher Resolution (Rev. A) Apr. 01, 2016
Technical articles “Touching” the smart grid infrastructure space with capacitive sensing technology Mar. 31, 2016
Technical articles Don’t miss out on the top training videos of 2015 Dec. 16, 2015
Application notes MSP Code Protection Features Dec. 07, 2015
Technical articles How fast is your 32-bit MCU? Jul. 15, 2015
Technical articles Lose power, not data with new FRAM microcontrollers May 20, 2015
Application notes Design Considerations When Using the MSP430 Graphics Library Oct. 05, 2012
Application notes Migrating from the USCI Module to the eUSCI Module (Rev. A) Sep. 13, 2012
White papers Power Management Solutions for Ultra-Low-Power 16-Bit MSP430 MCUs (Rev. D) Mar. 28, 2012
Application notes Migrating from the MSP430F2xx Family to the MSP430FR57xx Family (Rev. A) Feb. 16, 2012
Application notes Powering the MSP430 from a High Voltage Input using the TPS62122 (Rev. C) Jan. 12, 2012
Application notes 1.8V – 5.5V Input, High-Efficiency DCDC Converter Reference Design for MSP430 (Rev. B) Jun. 14, 2010
Application notes Tiny DCDC Converter Reference Design (Rev. A) Jun. 14, 2010

Design & development

For additional terms or required resources, click any title below to view the detail page where available.

Hardware development

EVALUATION BOARDS Download
document-generic User guide
75
Description

The DRV8106S-Q1EVM is designed to evaluate the DRV8106S-Q1, which is an integrated, automotive qualified brushed DC motor driver. The DRV8106S-Q1 is a highly integrated half-bridge gate driver, capable of driving high-side and low-side N-channel power MOSFETs. It generates the proper gate drive (...)

Features
  • Half-bridge smart gate driver EVM for automotive applications
    • Temperature grade 1: –40°C to +125°C, TA
    • 4.9-V to 37-V operating range
    • Doubler charge pump for 100% PWM
    • Half-bridge control mode
    • SPI interface for detailed configuration and diagnostics
  • Smart gate drive architecture
    • Adjustable slew rate control
    • (...)
EVALUATION BOARDS Download
document-generic User guide
75
Description

The DRV8424E evaluation module (EVM) allows easy evaluation of the DRV8424E device.

The DRV8424E devices are integrated motor-driver solutions for bipolar stepper motors or brushed DC motors. The device integrates two N-channel power MOSFET H-bridges, integrated current sense and regulation (...)

Features
  • 4.5-V to 33-V operating voltage range
  • Up to 4-A peak current
  • A simple PHASE/EN input interface
  • Integrated current sense
  • Smart tune technology
EVALUATION BOARDS Download
document-generic User guide
Description

The DRV8424 evaluation module (EVM) allows easy evaluation of the DRV8424 device.

The DRV8424 devices are integrated motor-driver solutions for bipolar stepper motors. The device integrates two N-channel power MOSFET H-bridges, integrated current sense and regulation circuitry, and a microstepping (...)

Features
  • 4.5-V to 33-V operating voltage range
  • Up to 4-A peak current
  • A simple STEP/DIR input interface
  • Integrated current sense and microstepping indexer
  • Smart tune technology
EVALUATION BOARDS Download
document-generic User guide
75
Description

The DRV8424P evaluation module (EVM) allows easy evaluation of the DRV8424P device.

The DRV8424P devices are integrated motor-driver solutions for bipolar stepper motors or brushed DC motors. The device integrates two N-channel power MOSFET H-bridges, integrated current sense and regulation (...)

Features
  • 4.5-V to 33-V operating voltage range
  • Up to 4-A peak current
  • A simple PWM input interface
  • Integrated current sense
  • Smart tune technology
EVALUATION BOARDS Download
document-generic User guide
75
Description

The DRV8426E evaluation module (EVM) allows easy evaluation of the DRV8426E device.

The DRV8426E devices are integrated motor-driver solutions for bipolar stepper motors or brushed DC motors. The device integrates two N-channel power MOSFET H-bridges, integrated current sense and regulation (...)

Features
  • 4.5-V to 33-V operating voltage range
  • Up to 2.5-A Peak current
  • A simple PHASE/EN input interface
  • Integrated current sense
  • Smart tune technology
EVALUATION BOARDS Download
document-generic User guide
75
Description

The DRV8426 evaluation module (EVM) allows easy evaluation of the DRV8426 device.

The DRV8426 devices are integrated motor-driver solutions for bipolar stepper motors. The device integrates two N-channel power MOSFET H-bridges, integrated current sense and regulation circuitry, and a microstepping (...)

Features
  • 4.5-V to 33-V operating voltage range
  • Up to 2.5-A peak current
  • A simple STEP/DIR input interface
  • Integrated current sense and microstepping indexer
  • Smart tune technology
EVALUATION BOARDS Download
document-generic User guide
75
Description

The DRV8426P evaluation module (EVM) allows easy evaluation of the DRV8426P device.

The DRV8426P devices are integrated motor-driver solutions for bipolar stepper motors or brushed DC motors. The device integrates two N-channel power MOSFET H-bridges, integrated current sense and regulation (...)

Features
  • 4.5-V to 33-V operating voltage range
  • Up to 2.5-A peak current
  • A simple PWM input interface
  • Integrated current sense
  • Smart tune technology
EVALUATION BOARDS Download
document-generic User guide
75
Description

The DRV8428E evaluation module (EVM) allows easy evaluation of the DRV8428E device.

The DRV8428E devices are integrated motor-driver solutions for bipolar stepper motors or brushed DC motors. The device integrates two N-channel power MOSFET H-bridges, integrated current sense and regulation (...)

Features
  • 4.5-V to 33-V operating voltage range
  • Up to 1-A peak current
  • A simple PHASE/EN input interface
  • Integrated current sense
  • Smart tune technology
EVALUATION BOARDS Download
document-generic User guide
75
Description

The DRV8428 evaluation module (EVM) allows easy evaluation of the DRV8428 device.

The DRV8428 devices are integrated motor-driver solutions for bipolar stepper motors. The device integrates two N-channel power MOSFET H-bridges, integrated current sense and regulation circuitry, and a microstepping (...)

Features
  • 4.5-V to 33-V operating voltage range
  • Up to 1-A peak current
  • A simple STEP/DIR input interface
  • Integrated current sense
  • Smart tune technology
EVALUATION BOARDS Download
document-generic User guide
75
Description

The DRV8428P evaluation module (EVM) allows easy evaluation of the DRV8428P device.

The DRV8428P devices are integrated motor-driver solutions for bipolar stepper motors or brushed DC motors. The device integrates two N-channel power MOSFET H-bridges, integrated current sense and regulation (...)

Features
  • 4.5-V to 33-V operating voltage range
  • Up to 1-A peak current
  • A simple PWM input interface
  • Integrated current sense
  • Smart tune technology
EVALUATION BOARDS Download
document-generic User guide
75
Description

The DRV8436E evaluation module (EVM) allows easy evaluation of the DRV8436E device.

DRV8436E is an integrated motor-driver solution for bipolar stepper motors. The device integrates two N-channel power MOSFET H-bridges, integrated current sense and regulation circuitry, and a microstepping indexer (...)

Features
  • 4.5-V to 48-V operating voltage range
  • 2.5-A peak current
  • Simple PH/EN control interface
  • Integrated current sense
  • Smart-tune technology
EVALUATION BOARDS Download
document-generic User guide
75
Description

The DRV8436 evaluation module (EVM) allows easy evaluation of the DRV8436 device.

The DRV8436 devices are integrated motor-driver solutions for bipolar stepper motors. The device integrates two N-channel power MOSFET H-bridges, integrated current sense and regulation circuitry, and a microstepping (...)

Features
  • 4.5-V to 48-V operating voltage range
  • 2.5-A peak current
  • A simple STEP/DIR interface
  • Integrated current sense and microstepping indexer
  • Smart tune technology
EVALUATION BOARDS Download
document-generic User guide
75
Description

The DRV8436P evaluation module (EVM) allows easy evaluation of the DRV8436P device.

DRV8436P is an integrated motor-driver solution for bipolar stepper motors. The device integrates two N-channel power MOSFET H-bridges, integrated current sense and regulation circuitry, and a microstepping indexer (...)

Features
  • 4.5-V to 48-V operating voltage range
  • 2.5-A peak current
  • Simple PWM control interface
  • Integrated current sense
  • Smart-tune technology
EVALUATION BOARDS Download
document-generic User guide
75
Description

The DRV8705S-Q1EVM is designed to evaluate the DRV8705H-Q1, which is an integrated, automotive qualified brushed DC motor driver. The DRV8705S-Q1 is a highly integrated H-bridge gate driver, capable of driving high-side and low-side N-channel power MOSFETs. It generates the proper gate drive (...)

Features
  • H-bridge smart gate driver EVM for automotive applications
    • Temperature grade 1: –40°C to +125°C, TA
    • 4.9-V to 37-V operating range
    • Doubler charge pump for 100% PWM
    • Half-bridge and H-bridge control modes
    • SPI interface for simple configuration
  • Smart gate drive architecture
    • Adjustable slew rate control
    • 1.0-mA (...)
EVALUATION BOARDS Download
document-generic User guide
75
Description

The DRV8706S-Q1EVM is designed to evaluate the DRV8706S-Q1, which is an integrated, automotive qualified brushed DC motor driver. The DRV8706S-Q1 is a highly integrated H-bridge gate driver, capable of driving high-side and low-side N-channel power MOSFETs. It generates the proper gate drive (...)

Features
  • H-bridge smart gate driver EVM for automotive applications
    • Temperature grade 1: –40°C to +125°C, TA
    • 4.9-V to 37-V operating range
    • Doubler charge pump for 100% PWM
    • Half-bridge and H-bridge control modes
    • SPI interface for detailed configuration and diagnostics
  • Smart gate drive architecture
    • Adjustable slew (...)
EVALUATION BOARDS Download
document-generic User guide
99
Description

The DRV8711 is a stepper motor controller using external N-channel MOSFETs to drive a bipolar stepper motor or two brushed DC motors. A microstepping indexer is integrated, supporting up to 1/256 microstep. The DRV8711 is capable of providing ultra-smooth motion profile, and motor stall can be (...)

Features
  • Built-in 1/256-step microstepping indexer
  • N-channel NexFET power MOSFETs
  • Ultra-smooth motion profile
  • Integrated stall detection reported on logic-level output pin
  • Complete protection and diagnosis
  • User-friendly GUI
  • Stepper motor included
  • Configurable for dual DC motor control
EVALUATION BOARDS Download
document-generic User guide
149
Description

The DRV8714S-Q1 evaluation module (EVM) allows easy evaluation of the DRV8714S-Q1 device.

The DRV8714S-Q1 is 4-channel Gate Driver with inline current sensing and offline diagnostics. The DRV8714S-Q1 devices can be powered with a supply voltage from 4.9 to 37 V. A smart gate drive architecture (...)

Features
  • 4.9-V to 37-V operating voltage range
  • 4 channel smart multi-stage gate driver
  • 4 PWM inputs with output mapping
  • 2x wide common mode current shunt amplifiers
  • SPI and H/W Multiple interface options available
EVALUATION BOARDS Download
document-generic User guide
149
Description

The DRV8718S-Q1 evaluation module (EVM) allows easy evaluation of the DRV8718S-Q1 device.

The DRV8718S-Q1 is 8-channel Gate Driver with inline current sensing and offline diagnostics. The DRV8718S-Q1 devices can be powered with a supply voltage from 4.9 to 37 V. A smart gate drive architecture (...)

Features
  • 4.9-V to 37-V operating voltage range
  • 8 channel smart multi-stage gate driver
  • 4 PWM inputs with output mapping
  • 2x wide common mode current shunt amplifiers
  • SPI and H/W multiple interface options available
EVALUATION BOARDS Download
document-generic User guide
99
Description

The DRV8805 evaluation module consists of a quad low-side motor driver with built-in indexer control interface that can be used to drive a unipolar stepper motor in full-step, half-step or wave mode. With the DRV8805EVM, designers can quickly and easily evaluate the performance of DRV8805 motor (...)

Features
  • 1.5A Continuous Current Single Channel Output
  • 800mA Continuous Current, 4 channels ON
  • Wide Operating Voltage Range: 8.2 to 60 V
  • Low RDSON (500mΩ)
  • Includes terminal as well as kelvin connections for all DRV8805 signals.
  • Includes USB port for programming of the microprocessor.
  • EVM includes LED indicator of (...)
EVALUATION BOARDS Download
document-generic User guide
99
Description

The DRV8834 evaluation module (EVM) demonstrates the capabilities and performance of the DRV8834 motor driver from Texas Instruments. This EVM comes with an on-board MSP430 microcontroller which has been pre-programmed with a set of useful algorithms for driving a stepper or two brushed DC motors (...)

Features
  • Microstep using DRV8834 internal indexer, on-board MSP430, or external MCU.
  • On-board potentiometers allows for adjusting Vref and decay ratio, blanking time and off time.
  • Control and status signals brought out to test headers for easy evaluation.
  • Headers and a simple jumper are provided so that the (...)
EVALUATION BOARDS Download
document-generic User guide
49
Description

This dual H-bridge driver with integrated FETs, DRV8880 can drive stepper motor drivers up to 1/16 microstepping with an on-chip indexer. Aimed at 24V motors, this device features AutoTune(TM) adaptive decay mode, which automatically adjusts the decay settings during operation to achieve the motor's (...)

Features
  • DRV8880 6.5-45V, dual H-bridge stepper motor driver with AutoTune™ adaptive decay
  • MSP430 MCU onboard
  • GUI for tuning
  • Supports 2.0A full-scale/1.4A RMS current output to motor
EVALUATION BOARDS Download
document-generic User guide
49
Description

DRV8881E is a dual H-bridge motor driver that can drive either a stepper motor or dual brushed DC motor driver with a Phase/Enable control interface. For stepper motors, this device also features TI's AutoTune™ adaptive decay mode. Aimed at 24V motors, this device also features AutoTune&trade (...)

Features
  • DRV8881E 6.5-45V, dual H-bridge motor driver
  • MSP430 MCU onboard
  • GUI for tuning
  • Supports 1.4A RMS current output to motor per H-bridge (2.5A peak)
EVALUATION BOARDS Download
document-generic User guide
49
Description

DRV8881P is a dual H-bridge motor driver that can drive either a stepper motor or dual brushed DC motor with a PWM control interface. Also aimed at 24V motors, this device supports slow, fast and mixed decay settings to tune the motors' performance. The DRV8881PEVM (evaluation module) serves as a (...)

Features
  • DRV8881P 6.5-45V, dual H-bridge motor driver
  • MSP430 MCU onboard
  • GUI for tuning
  • Supports 1.4A RMS current output to motor per H-bridge (2.5A peak)
EVALUATION BOARDS Download
document-generic User guide
49
Description
The DRV8884 evaluation module (EVM) demonstrates the integrated current sensing capabilities and performance of the DRV8884 integrated circuit from Texas Instruments. The EVM includes the DRV8885 to control a stepper motor, a MSP430F2617 to control the DRV8884 inputs, and a USB to UART to (...)
Features
  • Integrated current sense to minimize cost and power
  • 8-V to 37-V operating supply voltage range
  • Multiple decay modes
  • Adjustable current regulation
  • User-friendly GUI via MSP430 and USB interface
EVALUATION BOARDS Download
document-generic User guide
49
Description

The DRV8885 evaluation module (EVM) demonstrates the integrated current sensing capabilities and performance of the DRV8885 integrated circuit from Texas Instruments. The EVM includes the DRV8885 to control a stepper motor, a MSP430F2617 to control the DRV8885 inputs, and a USB to UART to (...)

Features
  • Integrated Current Sense to minimize cost and power
  • 8 V to 37 V Operating Supply Voltage Range
  • Multiple Decay Modes
  • Adjustable current regulation
  • User-friendly GUI via MSP430 and USB interface
EVALUATION BOARDS Download
document-generic User guide
49
Description
The DRV8886AT evaluation module (EVM) demonstrates the integrated current sensing capabilities and performance of the DRV8886AT integrated circuit from Texas Instruments. The EVM includes the DRV8886AT to control a stepper motor, a MSP430F2617 to control the DRV8886AT inputs, and a USB to UART to (...)
Features
  • Integrated Current Sense to minimize cost and power
  • 8V to 37V Operating Supply Voltage Range
  • Multiple Decay Modes
  • Adjustable Current Regulation
  • User-friendly GUI via MSP430 and USB interface
EVALUATION BOARDS Download
document-generic User guide
49
Description
The DRV8886 evaluation module (EVM) demonstrates the integrated current sensing capabilities and performance of the DRV8886 integrated circuit from Texas Instruments. The EVM includes the DRV8886 to control a stepper motor, a MSP430F2617 to control the DRV8886 inputs, and a USB to UART to (...)
Features
  • Integrated Current Sense to minimize cost and power
  • 8V to 37V Operating Supply Voltage Range
  • Multiple Decay Modes
  • Adjustable current regulation
  • User-friendly GUI via MSP430 and USB interface
EVALUATION BOARDS Download
document-generic User guide
75
Description

The DRV8889-Q1 evaluation module (EVM) allows easy evaluation of the DRV8889-Q1 device. The DRV8889-Q1 device is an integrated, dual H-bridge driver for automotive stepper motor applications.

The evaluation module allows the device to be configured for all of its functional modes including (...)

Features
  • 4.5-V to 40-V operating voltage range
  • Full stepping and microstepping modes down to 1/256
  • Programmable decay modes for stepper tuning, including dynamic decay and ripple control smart tuning modes
  • Stall detection
  • Slip detection
EVALUATION BOARDS Download
document-generic User guide
75
Description

The DRV8899-Q1 evaluation module (EVM) allows easy evaluation of the DRV8899-Q1 device. The DRV8899-Q1 device is an integrated, dual H-bridge driver for automotive stepper motor applications.

The evaluation module allows the device to be configured for all of its functional modes including (...)

Features
  • 4.5-V to 45-V operating voltage range
  • Full stepping and microstepping modes down to 1/256
  • Programmable decay modes for stepper tuning, including dynamic decay and ripple control smart-tuning modes
  • Integrated current sensing function
  • SPI with daisy chain support
EVALUATION BOARDS Download
document-generic User guide
190
Description

The MSP-FET430U80 is a powerful flash emulation tool that includes the hardware and software required to quickly begin application development on the MSP430 MCU. It includes a ZIF socket target board and a USB debugging interface (MSP-FET) used to program and debug the MSP430 in-system through the (...)

Features
  • USB debugging interface (MSP-FET) connects a flash-based MSP430 MCU to a PC for real-time, in-system programming and debugging
  • Technical specifications:
    • Software configurable supply voltage between 1.8 and 3.6 volts at 100mA
    • Supports JTAG Security Fuse blow to protect code
    • Supports all MSP430 boards (...)
DEVELOPMENT KITS Download
document-generic User guide
89
Description

The MSP-TS430PM64 is a standalone ZIF socket target board used to program and debug the MSP430 MCU in-system through the JTAG interface or the Spy Bi-Wire (2-wire JTAG) protocol.

Device Support: The MSP-TS430PM64 development board supports MSPF13x, MSP430F14x, MSP430F14x1, MSP430F15x, MSP430F16x (...)

Features
  • Development board (MSP-TS430PM64) with a ZIF socket fitting MSP430 derivatives in 64-pin LQFP (PM) packages includes an LED indicator, JTAG adapter, and header pin-outs for prototyping
  • Supports all debugging interfaces using a standard 14-pin JTAG header such as the MSP-FET430UIF
DEVELOPMENT KITS Download
document-generic User guide
89
Description

The MSP-TS430PN80 is a standalone ZIF socket target board used to program and debug the MSP430 MCU in-system through the JTAG interface or the Spy Bi-Wire (2-wire JTAG) protocol.

Device Support: The MSP-TS430PN80 development board supports MSP430F241x, MSP430F261x, MSP430F43x, MSP430F43x1 (...)

Features
  • Development board (MSP-TS430PN80) with a ZIF socket fitting some MSP430 derivatives in 80-pin LQFP (PN) packages includes an LED indicator, JTAG adapter, and header pin-outs for prototyping
  • Supports all debugging interfaces using a standard 14-pin JTAG header such as the MSP-FET430UIF

Software development

SOFTWARE DEVELOPMENT KITS (SDK) Download
MSP430Ware for MSP Microcontrollers
MSPWARE MSP430Ware is a collection of resources that help users to effectively create and build MSP430 code. These resources support ALL MSP430 microcontrollers (MCUs). As one user mentioned, “It’s essentially everything developers need to become MSP430 microcontroller experts!”

This complete collection of (...)

Features
  • Collection of MSP design resources
  • Available within CCS, as a standalone executable, or as part of TI’s new Cloud-based tools
  • Auto-updates through the web
  • Sleek & intuitive GUI for browsing content
  • Features the MSP Driver Library
  • Automatic filtering of content using a unique 2-pane view
CODE EXAMPLES & DEMOS Download
SLAC151K.ZIP (730 KB)
DRIVERS & LIBRARIES Download
Digital Signal Processing (DSP) Library for MSP430 Microcontrollers
MSP-DSPLIB — The Texas Instruments MSP430™ Digital Signal Processing library is a set of highly optimized functions to perform many common signal processing operations on fixed-point numbers for MSP430 microcontrollers. This function set is typically used in applications where processing-intensive (...)
DRIVERS & LIBRARIES Download
MSP Graphics Library
MSP-GRLIB The MSP Graphics Library is a royalty-free set of graphics primitives for creating graphical user interfaces on MSP430 and MSP432 microcontroller-based boards that have a graphical display. The graphical library consists of two building layers of functionality: the display driver layer, specific to (...)
Features
  • Free license and royalty-free use
  • Simplify and accelerate developmen tof applications
  • Easy-to-maintain code
DRIVERS & LIBRARIES Download
Fixed Point Math Library for MSP
MSP-IQMATHLIB The Texas Instruments® MSP IQmath and Qmath Libraries are a collection of highly optimized and high-precision mathematical functions for C programmers to seamlessly port a floating-point algorithm into fixed-point code on MSP430 and MSP432 devices. These routines are typically used in (...)
Features
  • Optimized fixed point functions - reduce development time and enable developers to focus on optimizing application code
  • Up to 100x higher performance when executing common fixed point scalar math functions in CCS – this means the MSP microcontroller can remain in low power modes longer than (...)
DRIVERS & LIBRARIES Download
Bootloader (BSL) for MSP low-power microcontrollers
MSPBSL The bootloader (BSL) on MSP430™ microcontrollers (MCUs) lets users communicate with embedded memory in the MSP MCUs during the prototyping phase, final production, and in service. This is done through standard interfaces such as UART, I2C, SPI, and USB. Both the programmable memory (...)
IDES, CONFIGURATION, COMPILERS & DEBUGGERS Download
Code Composer Studio™ Integrated Development Environment for MSP Microcontrollers
CCSTUDIO-MSP

Code Composer Studio is an integrated development environment (IDE) that supports TI's Microcontroller and Embedded Processors portfolio. Code Composer Studio comprises a suite of tools used to develop and debug embedded applications. It includes an optimizing C/C++ compiler, source code editor (...)

IDES, CONFIGURATION, COMPILERS & DEBUGGERS Download
EnergyTrace Technology
ENERGYTRACE EnergyTrace™ software for MSP430™ MCUs, MSP432™ MCUs, CC13xx wireless MCUs and CC26xx wireless MCUs is an energy-based code analysis tool that measures and displays the energy profile of an application and helps optimize it for ultra-low-power consumption.

As most developers know, it is difficult to (...)

Features
  • Current measurement is enabled for all MSP430 MCUs, MSP432 MCUs and connectivity devices
  • Tracing of CPU states is available on selected MSP430 MCUs, MSP432 MCUs, CC13x2 wireless MCUs and CC26x2 wireless MCUs 
  • Tracing of peripheral states is also available on selected MSP430 MCUs, CC13x2 (...)
IDES, CONFIGURATION, COMPILERS & DEBUGGERS Download
IAR Embedded Workbench
Provided by IAR Systems IAR Embedded Workbench for MSP430 (EW430)
IAR Embedded Workbench for MSP430 is a complete debugger and C/C++ compiler toolchain for building and debugging embedded applications based on MSP430 microcontrollers. The Debugger is a fully integrated debugger for source and disassembly level debugging (...)
PROGRAMMING TOOLS Download
MSP MCU Programmer and Debugger
MSP-FET The MSP-FET is a powerful emulation development tool – often called a debug probe – which allows users to quickly begin development on MSP low-power microcontrollers (MCU).

It supports programming and real-time debugging over both JTAG and SBW interfaces. Furthermore, the MSP-FET also provides a (...)

115
Features
  • USB debugging interface to connect any MSP430 MCU to a computer for real-time, in-system programming and debugging
  • Enables EnergyTrace™ technology for energy measurement and debugging on all MSP430 and MSP432 devices in the Code Composer Studio and IAR Embedded Workbench development environments
  • (...)
PROGRAMMING TOOLS Download
MSP-GANG Production Programmer
MSP-GANG The MSP Gang Programmer (MSP-GANG) is a MSP430™/MSP432™ device programmer that can program up to eight identical MSP430/MSP432 Flash or FRAM devices at the same time. It connects to a host PC using a standard RS-232 or USB connection and provides flexible programming options that allow (...)
Features
  • Quickly and reliably program Flash or FRAM-based MSP devices via RS-232 or USB interface
  • Several programming modes:
    • Interactive Mode – Programming while connected to PC using the MSP GANG Programmer GUI
    • Program from Image – An image can be stored, which contains configuration options and code (...)
PROGRAMMING TOOLS Download
UniFlash stand-alone flash tool for microcontrollers, Sitara™; processors and SimpleLink™
UNIFLASH Supported devices: CC13xx, CC25xx, CC26xx, CC3x20, CC3x30, CC3x35, Tiva, C2000, MSP43x, Hercules, PGA9xx, IWR12xx, IWR14xx, IWR16xx, IWR18xx , IWR68xx, AWR12xx, AWR14xx, AWR16xx, AWR18xx.  Command line only: AM335x, AM437x, AM571x, AM572x, AM574x, AM65XX, K2G

CCS Uniflash is a standalone tool used to (...)

Design tools & simulation

CAD/CAE SYMBOLS Download
SLAC060E.ZIP (97 KB)

Reference designs

REFERENCE DESIGNS Download
Closed Loop Stepper Motor Reference Design With Encoder for Stall-Detection
TIDA-01370 — TIDA-01370 is a TI design used for the stall-detection in a stepper motor driven by the DRV8880 in the presence of a closed loop feedback obtained with an optical rotary incremental encoder.  The reference design shows how to detect a stall using a closed-loop algorithm.
document-generic Schematic document-generic User guide
REFERENCE DESIGNS Download
24V Stepper Motor Controller with Integrated Current Sense Reference Design
TIDA-00867 The TIDA-00867 reference design showcases the benefits of integrated current sensing for stepper motors. Integraded current sensing is available on the DRV8885. The DRV8885EVM to demonstrate this feature.
document-generic Schematic document-generic User guide
REFERENCE DESIGNS Download
24V Stepper Motor Design with AutoTune Reference Design
TIDA-00830 TIDA-00830 is an application overview of TI’s automatic stepper motor tuning feature known as AutoTune™.  This design showcases how quickly AutoTune can adapt to changes in system inputs or motor characteristics without the user having to apply any type of parameter tuning.  (...)
document-generic Schematic document-generic User guide
REFERENCE DESIGNS Download
Stepper Motor System with Medium Torque Drive
TIDA-00111 This bipolar stepper motor system implements an MSP430, a DRV8818, and a NEMA 23 motor.  It's suitable for applications requiring up to 140 oz-in of torque, and up to 800 RPM.  Motor voltage support is 8V to 35V, and max current is 2.5A.  A multitude of configuration options allow (...)
document-generic Schematic document-generic User guide
Design files

CAD/CAE symbols

Package Pins Download
BGA MICROSTAR JUNIOR (ZQW) 113 View options
LQFP (PM) 64 View options
LQFP (PN) 80 View options
NFBGA (ZCA) 113 View options

Ordering & quality

Recommended products may have parameters, evaluation modules or reference designs related to this TI product.

Support & training

TI E2E™ forums with technical support from TI engineers

Content is provided "as is" by TI and community contributors and does not constitute TI specifications. See terms of use.

If you have questions about quality, packaging or ordering TI products, see TI support. ​​​​​​​​​​​​​​

Videos

Related videos