Rotary Sensing MCU with extended scan interface, 64KB FRAM, 2KB SRAM for flow meters
Product details
Parameters
Package | Pins | Size
Features
- Embedded Microcontroller
- 16-Bit RISC Architecture up to 16-MHz Clock
- Wide Supply Voltage Range From 3.6 V Down to 1.8 V (Minimum Supply Voltage is Restricted by SVS Levels, See the SVS Specifications)
- Optimized Ultra-Low-Power Modes
- Active Mode: Approximately 100 µA/MHz
- Standby (LPM3 With VLO): 0.4 µA (Typical)
- Real-Time Clock (RTC) (LPM3.5): 0.35 µA (Typical) (1)
- Shutdown (LPM4.5): 0.02 µA (Typical)
- Ultra-Low-Power Ferroelectric RAM (FRAM)
- Up to 128KB of Nonvolatile Memory
- Ultra-Low-Power Writes
- Fast Write at 125 ns per Word (64KB in 4 ms)
- Unified Memory = Program + Data + Storage in One Single Space
- 1015 Write Cycle Endurance
- Radiation Resistant and Nonmagnetic
- Intelligent Digital Peripherals
- 32-Bit Hardware Multiplier (MPY)
- Three-Channel Internal Direct Memory Access (DMA)
- RTC With Calendar and Alarm Functions
- Five 16-Bit Timers With up to 7 Capture/Compare Registers Each
- 16-Bit and 32-Bit Cyclic Redundancy Checker (CRC16, CRC32)
- High-Performance Analog
- Extended Scan Interface (ESI) for Background Water, Heat, and Gas Volume Measurement
- 16-Channel Analog Comparator
- 12-Bit Analog-to-Digital Converter (ADC) With Internal Reference and Sample-and-Hold and up to 16 External Input Channels
- Integrated LCD Driver With Contrast Control for up to 320 Segments
- Multifunction Input/Output Ports
- All P1 to P10 and PJ Pins Support Capacitive Touch Capability Without Need for External Components
- Accessible Bit-, Byte- and Word-Wise (in Pairs)
- Edge-Selectable Wakeup From LPM on Ports P1, P2, P3, and P4
- Programmable Pullup and Pulldown on All Ports
- Code Security
- True Random Number Seed for Random Number Generation Algorithm
- Enhanced Serial Communication
- eUSCI_A0 and eUSCI_A1 Support:
- UART With Automatic Baud-Rate Detection
- IrDA Encode and Decode
- SPI
- eUSCI_B0 and eUSCI_B1 Support:
- I2C With Multiple-Slave Addressing
- SPI
- Hardware UART and I2C Bootloader (BSL)
- eUSCI_A0 and eUSCI_A1 Support:
- Flexible Clock System
- Fixed-Frequency DCO With 10 Selectable Factory-Trimmed Frequencies
- Low-Power Low-Frequency Internal Clock Source (VLO)
- 32-kHz Crystals (LFXT)
- High-Frequency Crystals (HFXT)
- Development Tools and Software
- Free Professional Development Environments With EnergyTrace++™ Technology
- Experimenter and Development Kits
- Family Members
- Device Comparison Summarizes the Device Variants and Available Packages Types
- For Complete Module Descriptions, See the MSP430FR58xx, MSP430FR59xx, and MSP430FR6xx Family User’s Guide
(1)RTC is clocked by a 3.7-pF crystal.
All trademarks are the property of their respective owners.
Description
The MSP430™ ultra-low-power (ULP) FRAM platform combines uniquely embedded FRAM and a holistic ultra-low-power system architecture, allowing innovators to increase performance at lowered energy budgets. FRAM technology combines the speed, flexibility, and endurance of SRAM with the stability and reliability of flash at much lower power.
The MSP430 ULP FRAM portfolio consists of a diverse set of devices that feature FRAM, the ULP 16-bit MSP430 CPU, and intelligent peripherals targeted for various applications. The ULP architecture showcases seven low-power modes, which are optimized to achieve extended battery life in energy-challenged applications.
Technical documentation
Design & development
For additional terms or required resources, click any title below to view the detail page where available.Hardware development
Description
The MSP-FET430U100D is a bundle featuring the MSP-FET programmer/debugger with the MSP-TS430PZ100D, a standalone 100-pin ZIF socket target board. This bundle can be used to program and debug the MSP430 MCU in-system through the JTAG interface or the Spy Bi-Wire (2-wire JTAG) protocol.
Device Support (...)
Features
- Unified FRAM Memory for lowest power, fastest non-volatile memory
- Ultra-low-leakage 130nm Process technology
- Enhanced MSP430 DNA with Power gating and load adaptive LDO
- Integrated analog and digital peripherals to lower cost and simplify design for applications including flow metering
- Integrated LCD (...)
Description
The MSP-TS430PZ100D is a standalone 100-pin ZIF socket target board used to program and debug the MSP430 MCU in-system through the JTAG interface or the Spy Bi-Wire (2-wire JTAG) protocol.
Device Support: The MSP-TS430PZ100D development board supports MSP430FR69xx FRAM MCUs in a 100-pin LQFP package (...)
Features
- Unified FRAM Memory for lowest power, fastest non-volatile memory
- Ultra-low-leakage 130nm Process technology
- Enhanced MSP430 DNA with Power gating and load adaptive LDO
- Integrated analog and digital peripherals to lower cost and simplify design for applications including flow metering: Integrated LCD (...)
Description
The MSP-FET is a powerful emulation development tool – often called a debug probe – which allows users to quickly begin development on MSP low-power microcontrollers (MCU).
It supports programming and real-time debugging over both JTAG and SBW interfaces. Furthermore, the MSP-FET also provides a (...)
Features
- USB debugging interface to connect any MSP430 MCU to a computer for real-time, in-system programming and debugging
- Enables EnergyTrace™ technology for energy measurement and debugging on all MSP430 and MSP432 devices in the Code Composer Studio and IAR Embedded Workbench development environments
- (...)
Description
The MSP Gang Programmer (MSP-GANG) is a MSP430™/MSP432™ device programmer that can program up to eight identical MSP430/MSP432 Flash or FRAM devices at the same time. It connects to a host PC using a standard RS-232 or USB connection and provides flexible programming options that allow (...)
Features
- Quickly and reliably program Flash or FRAM-based MSP devices via RS-232 or USB interface
- Several programming modes:
- Interactive Mode – Programming while connected to PC using the MSP GANG Programmer GUI
- Program from Image – An image can be stored, which contains configuration options and code (...)
Software development
This complete collection of (...)
Features
- Collection of MSP design resources
- Available within CCS, as a standalone executable, or as part of TI’s new Cloud-based tools
- Auto-updates through the web
- Sleek & intuitive GUI for browsing content
- Features the MSP Driver Library
- Automatic filtering of content using a unique 2-pane view
Features
- Free license and royalty-free use
- Simplify and accelerate development of applications
- Easy-to-maintain code
Features
- Up to 26x higher performance when executing floating point scalar math functions
- Remains in low power modes longer due to the increased performance
- Free and easy to use – now integrated in CCS and IAR
Code Composer Studio is an integrated development environment (IDE) that supports TI's Microcontroller and Embedded Processors portfolio. Code Composer Studio comprises a suite of tools used to develop and debug embedded applications. It includes an optimizing C/C++ compiler, source code editor (...)
As most developers know, it is difficult to (...)
Features
- Current measurement is enabled for all MSP430 MCUs, MSP432 MCUs and connectivity devices
- Tracing of CPU states is available on selected MSP430 MCUs, MSP432 MCUs, CC13x2 wireless MCUs and CC26x2 wireless MCUs
- Tracing of peripheral states is also available on selected MSP430 MCUs, CC13x2 (...)
Features
- Extended Scan Interface configuration via a graphical block diagram tool
- Generates fully functional CCS and IAR projects for up to 3 LC sensor configurations.
- Enables communication between PC and microcontroller via HID/UART communication bridge.
- Option to generate configuration file based on custom (...)
CCS Uniflash is a standalone tool used to (...)
Reference designs
CAD/CAE symbols
Package | Pins | Download |
---|---|---|
LQFP (PM) | 64 | View options |
VQFN (RGC) | 64 | View options |
Ordering & quality
- RoHS
- REACH
- Device marking
- Lead finish/Ball material
- MSL rating/Peak reflow
- MTBF/FIT estimates
- Material content
- Qualification summary
- Ongoing reliability monitoring
Support & training
TI E2E™ forums with technical support from TI engineers
Content is provided "as is" by TI and community contributors and does not constitute TI specifications. See terms of use.
If you have questions about quality, packaging or ordering TI products, see TI support.