24 MHz MCU with 16KB FRAM, 1KB SRAM, Comparator, UART/SPI/I2C, Timer
Product details
Parameters
Package | Pins | Size
Features
- Embedded Microcontroller
- 16-Bit RISC Architecture up to 24-MHz Clock
- Wide Supply Voltage Range (2 V to 3.6 V)
- –40°C to 85°C Operation
- Optimized Ultra-Low-Power Modes
- Active Mode: 81.4 µA/MHz (Typical)
- Standby (LPM3 With VLO): 6.3 µA (Typical)
- Real-Time Clock (RTC) (LPM3.5 With Crystal): 1.5 µA (Typical)
- Shutdown (LPM4.5): 0.32 µA (Typical)
- Ultra-Low-Power Ferroelectric RAM (FRAM)
- Up to 16KB of Nonvolatile Memory
- Ultra-Low-Power Writes
- Fast Write at 125 ns per Word (16KB in 1 ms)
- Built-In Error Correction Coding (ECC) and Memory Protection Unit (MPU)
- Universal Memory = Program + Data + Storage
- 1015 Write Cycle Endurance
- Radiation Resistant and Nonmagnetic
- Intelligent Digital Peripherals
- 32-Bit Hardware Multiplier (MPY)
- Three-Channel Internal DMA
- Real-Time Clock (RTC) With Calendar and Alarm Functions
- Five 16-Bit Timers With up to Three Capture/Compare Registers
- 16-Bit Cyclic Redundancy Checker (CRC)
- High-Performance Analog
- 16-Channel Analog Comparator With Voltage Reference and Programmable Hysteresis
- 12-Channel 10-Bit Analog-to-Digital Converter (ADC) With Internal Reference and Sample-and-Hold
- 200 ksps at 100-µA Consumption
- Enhanced Serial Communication
- eUSCI_A0 and eUSCI_A1 Support:
- UART With Automatic Baud-Rate Detection
- IrDA Encode and Decode
- SPI
- eUSCI_B0 Supports:
- I2C With Multiple-Slave Addressing
- SPI
- Hardware UART Bootloader (BSL)
- eUSCI_A0 and eUSCI_A1 Support:
- Power Management System
- Fully Integrated LDO
- Supply Voltage Supervisor for Core and Supply Voltages With Reset Capability
- Always-On Zero-Power Brownout Detection
- Serial Onboard Programming With No External Voltage Needed
- Flexible Clock System
- Fixed-Frequency DCO With Six Selectable Factory-Trimmed Frequencies (Device Dependent)
- Low-Power Low-Frequency Internal Clock Source (VLO)
- 32-kHz Crystals (LFXT)
- High-Frequency Crystals (HFXT)
- Development Tools and Software
- Free Professional Development Environment
(Code Composer Studio™ IDE) - Low-Cost Full-Featured Kit
(MSP-EXP430FR5739) - Full Development Kit (MSP-FET430U40A)
- Target Board (MSP-TS430RHA40A)
- Free Professional Development Environment
- Family Members
- See Family Members for Available Device Variants and Packages
- For Complete Module Descriptions, See the MSP430FR57xx Family User’s Guide
All trademarks are the property of their respective owners.
Description
The TI MSP430FR573x family of ultra-low-power microcontrollers consists of multiple devices that feature embedded FRAM nonvolatile memory, ultra-low-power 16-bit MSP430™ CPU, and different peripherals targeted for various applications. The architecture, FRAM, and peripherals, combined with seven low-power modes, are optimized to achieve extended battery life in portable and wireless sensing applications. FRAM is a new nonvolatile memory that combines the speed, flexibility, and endurance of SRAM with the stability and reliability of flash, all at lower total power consumption. Peripherals include a 10-bit ADC, a 16-channel comparator with voltage reference generation and hysteresis capabilities, three enhanced serial channels capable of I2C, SPI, or UART protocols, an internal DMA, a hardware multiplier, an RTC, five 16-bit timers, and digital I/Os.
Technical documentation
= Top documentation for this product selected by TI
Design & development
For additional terms or required resources, click any title below to view the detail page where available.Hardware development
Description
The MSP-TS430RHA40A is a standalone 40-pin ZIF socket target board used to program and debug the MSP430 MCU in-system through the JTAG interface or the Spy Bi-Wire (2-wire JTAG) protocol.
Device Support: The MSP-TS430RHA40A development board supports MSP430FR572x and MSP430FR573x FRAM MCUs in a (...)
Features
- Development board (MSP-TS430RHA40A) with a 40-pin ZIF socket fitting MSP430 derivatives in 40-pin QFN (RHA) packages includes an LED indicator, JTAG adapter, and header pin-outs for prototyping
- Supports all debugging interfaces using a standard 14-pin JTAG header such as the MSP-FET430UIF
Software development
MSPWARE — MSP430Ware is a collection of resources that help users to effectively create and build MSP430 code. These resources support ALL MSP430 microcontrollers (MCUs). As one user mentioned, “It’s essentially everything developers need to become MSP430 microcontroller experts!”
This complete collection of (...)
Features
- Collection of MSP design resources
- Available within CCS, as a standalone executable, or as part of TI’s new Cloud-based tools
- Auto-updates through the web
- Sleek & intuitive GUI for browsing content
- Features the MSP Driver Library
- Automatic filtering of content using a unique 2-pane view
MSP430-IEC60730-SW-PACKAGE — The IEC60730 MSP430 software package was developed to be useful in assisting customers in complying with IEC 60730-1:2010 (Automatic Electrical Controls for Household and Similar Use – Part 1: General Requirements) for up to Class B products, which includes home appliances, arc detectors (...)
Features
Supports testing these parts:
- MSP430G23xx
- MSP430G24xx
- MSP430G25xx
- MSP430G2x44
- MSP430G2x55
- MSP430F5xx
- MSP430FR2433
- MSP430FR25xx
- MSP430FR26xx
- MSP430FR57xx
MSP-DSPLIB — The Texas Instruments MSP430™ Digital Signal Processing library is a set of highly optimized functions to perform many common signal processing operations on fixed-point numbers for MSP430 microcontrollers. This function set is typically used in applications where processing-intensive (...)
MSP-FRAM-UTILITIES — The Texas Instruments FRAM Utilities is designed to grow as a collection of embedded software utilities that leverage the ultra-low-power and virtually unlimited write endurance of FRAM. The utilities are available for MSP430FRxx FRAM microcontrollers and provide example code to help start (...)
MSP-GRLIB — The MSP Graphics Library is a royalty-free set of graphics primitives for creating graphical user interfaces on MSP430 and MSP432 microcontroller-based boards that have a graphical display. The graphical library consists of two building layers of functionality: the display driver layer, specific to (...)
Features
- Free license and royalty-free use
- Simplify and accelerate developmen tof applications
- Easy-to-maintain code
MSP-IQMATHLIB — The Texas Instruments® MSP IQmath and Qmath Libraries are a collection of highly optimized and high-precision mathematical functions for C programmers to seamlessly port a floating-point algorithm into fixed-point code on MSP430 and MSP432 devices. These routines are typically used in (...)
Features
- Optimized fixed point functions - reduce development time and enable developers to focus on optimizing application code
- Up to 100x higher performance when executing common fixed point scalar math functions in CCS – this means the MSP microcontroller can remain in low power modes longer than (...)
MSPBSL — Below are the steps needed in order to both understand and use the MSPBSL effectively across the MSP portfolio. For the most up to date information on what features the BSL on your device supports or which interface methods are needed to communicate with the BSL, please see “TABLE 1. Overview (...)
MSPMATHLIB — Continuing to innovate in the low power and low cost microcontroller space, TI brings you MSPMATHLIB. Leveraging the intelligent peripherals of our devices, this floating point math library of scalar functions brings you up to 26x better performance.
Mathlib is easy to integrate into your designs. (...)
Features
- Up to 26x higher performance when executing floating point scalar math functions
- Remains in low power modes longer due to the increased performance
- Free and easy to use – now integrated in CCS and IAR
CCSTUDIO-MSP —
Code Composer Studio is an integrated development environment (IDE) that supports TI's Microcontroller and Embedded Processors portfolio. Code Composer Studio comprises a suite of tools used to develop and debug embedded applications. It includes an optimizing C/C++ compiler, source code editor (...)
ENERGYTRACE — EnergyTrace™ software for MSP430™ MCUs, MSP432™ MCUs, CC13xx wireless MCUs and CC26xx wireless MCUs is an energy-based code analysis tool that measures and displays the energy profile of an application and helps optimize it for ultra-low-power consumption.
As most developers know, it is difficult to (...)
Features
- Current measurement is enabled for all MSP430 MCUs, MSP432 MCUs and connectivity devices
- Tracing of CPU states is available on selected MSP430 MCUs, MSP432 MCUs, CC13x2 wireless MCUs and CC26x2 wireless MCUs
- Tracing of peripheral states is also available on selected MSP430 MCUs, CC13x2 (...)
Provided by IAR Systems — IAR Embedded Workbench for MSP430 (EW430)
IAR Embedded Workbench for MSP430 is a complete debugger and C/C++ compiler toolchain for building and debugging embedded applications based on MSP430 microcontrollers. The Debugger is a fully integrated debugger for source and disassembly level debugging (...)
IAR Embedded Workbench for MSP430 is a complete debugger and C/C++ compiler toolchain for building and debugging embedded applications based on MSP430 microcontrollers. The Debugger is a fully integrated debugger for source and disassembly level debugging (...)
MSP-FET — To get started developing:
Step 1: Buy the MSP-FET
Step 2: Refer to the debuggers user’s guide and hardware user’s guide.
Step 3: Refer to debugging video
Step 1: Buy the MSP-FET
Step 2: Refer to the debuggers user’s guide and hardware user’s guide.
Step 3: Refer to debugging video
**The second generation of the MSP-FET is supported in the IDEs since Code Composer Studio™ v7.0, IAR EW430 v7.1 and IAR EWAR v8.10. For use (...)
Features
- USB debugging interface to connect any MSP430 MCU to a computer for real-time, in-system programming and debugging
- Enables EnergyTrace™ technology for energy measurement and debugging on all MSP430 and MSP432 devices in the Code Composer Studio and IAR Embedded Workbench development environments
- (...)
MSP-GANG — The MSP Gang Programmer is a MSP430/MSP432 device programmer that can program up to eight identical MSP430/MSP432 Flash or FRAM devices at the same time. The MSP Gang Programmer connects to a host PC using a standard RS-232 or USB connection and provides flexible programming options that allow the (...)
Features
- Quickly and reliably program Flash or FRAM-based MSP devices via RS-232 or USB interface
- Several programming modes:
- Interactive Mode – Programming while connected to PC using the MSP GANG Programmer GUI
- Program from Image – An image can be stored, which contains configuration options and code (...)
UNIFLASH — Supported devices: CC13xx, CC25xx, CC26xx, CC3x20, CC3x30, CC3x35, Tiva, C2000, MSP43x, Hercules, PGA9xx, IWR12xx, IWR14xx, IWR16xx, IWR18xx , IWR68xx, AWR12xx, AWR14xx, AWR16xx, AWR18xx. Command line only: AM335x, AM437x, AM571x, AM572x, AM574x, AM65XX, K2G
CCS Uniflash is a standalone tool used to (...)
SLAC491J.ZIP (336 KB)
Reference designs
TIDM-FRAM-EEPROM — This TI Design reference design describes an implementation of emulating EEPROM using Ferroelectric Random Access Memory (FRAM) technology on MSP430™ ultra-low-power microcontrollers (MCUs) combined with the additional sensing capabilities that can be enabled when using an MCU. The reference (...)
CAD/CAE symbols
| Package | Pins | Download |
|---|---|---|
| VQFN (RHA) | 40 | View options |
Ordering & quality
Support & training
TI E2E™ forums with technical support from TI engineers
Content is provided "as is" by TI and community contributors and does not constitute TI specifications. See terms of use.
If you have questions about quality, packaging or ordering TI products, see TI support.