首頁 放大器 電流感測放大器 數位電源監測器
首頁
放大器
電流感測放大器
數位電源監測器

INA234

現行

採用 WCSP 且具有警報功能的 28-V、12 位元、I²C 輸出電流/電壓/電源監測器

立即訂購
產品規格表

INA234

現行
產品規格表 立即訂購

產品詳細資料

Common-mode voltage (max) (V) 28 Common-mode voltage (min) (V) -0.3 Digital interface I2C Resolution (Bits) 12 Input offset (±) (max) (µV) 100 Input offset drift (±) (max) (µV/°C) 0.5 Voltage gain (V/V) 1 CMRR (min) (dB) 100 Supply voltage (max) (V) 5.5 Supply voltage (min) (V) 1.7 Iq (max) (mA) 0.5 Gain error (%) 0.5 Gain error drift (±) (max) (ppm/°C) 50 Features Alert Function, Bidirectional, Integrated Power Monitor, Low-side Capable Number of channels 1 Power measurement accuracy (%) 1 Rating Catalog Operating temperature range (°C) -40 to 125
Common-mode voltage (max) (V) 28 Common-mode voltage (min) (V) -0.3 Digital interface I2C Resolution (Bits) 12 Input offset (±) (max) (µV) 100 Input offset drift (±) (max) (µV/°C) 0.5 Voltage gain (V/V) 1 CMRR (min) (dB) 100 Supply voltage (max) (V) 5.5 Supply voltage (min) (V) 1.7 Iq (max) (mA) 0.5 Gain error (%) 0.5 Gain error drift (±) (max) (ppm/°C) 50 Features Alert Function, Bidirectional, Integrated Power Monitor, Low-side Capable Number of channels 1 Power measurement accuracy (%) 1 Rating Catalog Operating temperature range (°C) -40 to 125
DSBGA (YBJ) 8 0.2316 mm² 1.2 x 0.193
  • High-side or low-side current sensing
  • Operates from a 1.7V to 5.5V power supply
  • Reports current, voltage and power
  • Programmable full scale range: 20mV / 80mV
  • Input common mode range: –0.3V to 28V
  • Current monitoring accuracy:
    • 12-bit ADC resolution
    • 0.5% gain error (maximum)
    • 100µV offset (maximum)
  • Low input bias current: 10nA (maximum)
  • Configurable averaging options
  • General call addressing allows conversion synchronization among devices
  • Alert limits for over and under current events
  • 1.2V compliant I2C, SMBus interface
  • Two device address options with a 4-pin selectable address
  • DSBGA-8 Package (0.745mm × 1.508mm)
  • Operating temperature: –40°C and +125°C
  • High-side or low-side current sensing
  • Operates from a 1.7V to 5.5V power supply
  • Reports current, voltage and power
  • Programmable full scale range: 20mV / 80mV
  • Input common mode range: –0.3V to 28V
  • Current monitoring accuracy:
    • 12-bit ADC resolution
    • 0.5% gain error (maximum)
    • 100µV offset (maximum)
  • Low input bias current: 10nA (maximum)
  • Configurable averaging options
  • General call addressing allows conversion synchronization among devices
  • Alert limits for over and under current events
  • 1.2V compliant I2C, SMBus interface
  • Two device address options with a 4-pin selectable address
  • DSBGA-8 Package (0.745mm × 1.508mm)
  • Operating temperature: –40°C and +125°C

The INA234 device is a 12-bit digital current monitor with an I2C/SMBus-compatible interface that is compliant with a wide range of digital bus voltages such as 1.2V, 1.8V, 3.3V, and 5V. The device monitors the voltage across an external sense resistor and reports values for current, bus voltage, and power.

The INA234 features programmable ADC conversion times and averaging. The device also has a programmable calibration value with an internal multiplier that enables direct readouts of current in amperes and power in watts. The device monitors the bus voltage present on the IN– pin and can alert on overcurrent and undercurrent conditions as well as overvoltage and undervoltage conditions. High input impedance while in current measurement mode allows use of larger current sense resistors needed to measure small value system currents.

The INA234 senses current on common-mode bus voltages that can vary from –0.3V to 28V, independent of the supply voltage. The device operates from a single 1.7V to 5.5V supply, drawing a typical supply current of 300µA in normal operation. The device can be placed in a low-power standby mode where the typical operating current is 2.2µA.

The INA234 device is a 12-bit digital current monitor with an I2C/SMBus-compatible interface that is compliant with a wide range of digital bus voltages such as 1.2V, 1.8V, 3.3V, and 5V. The device monitors the voltage across an external sense resistor and reports values for current, bus voltage, and power.

The INA234 features programmable ADC conversion times and averaging. The device also has a programmable calibration value with an internal multiplier that enables direct readouts of current in amperes and power in watts. The device monitors the bus voltage present on the IN– pin and can alert on overcurrent and undercurrent conditions as well as overvoltage and undervoltage conditions. High input impedance while in current measurement mode allows use of larger current sense resistors needed to measure small value system currents.

The INA234 senses current on common-mode bus voltages that can vary from –0.3V to 28V, independent of the supply voltage. The device operates from a single 1.7V to 5.5V supply, drawing a typical supply current of 300µA in normal operation. The device can be placed in a low-power standby mode where the typical operating current is 2.2µA.
filter 尋找其它 數位電源監測器
下載 觀看有字幕稿的影片 影片

技術文件

star =TI 所選的此產品重要文件
找不到結果。請清除您的搜尋條件，然後再試一次。
檢視所有 10
重要文件 類型 標題 格式選項 日期
* Data sheet INA234 28V , 12-Bit , Current, Voltage, and Power Monitor With an I2 C Interface datasheet (Rev. D) PDF | HTML 2025年 8月 27日
Application note Aliasing and Prevention in Some Capacitively Coupled Current Sense Amplifiers PDF | HTML 2025年 11月 6日
Application note Closed Loop Constant Power Drive to Simplify Heater Element Control and Extend Battery Life PDF | HTML 2025年 1月 29日
Application note Risks and Prevention of ESD, EOS, and Latch Up Events for Current Sense Amplifiers PDF | HTML 2024年 11月 18日
Application note Using a PCB Copper Trace as a Current-Sense Shunt Resistor PDF | HTML 2022年 1月 25日
Application note Digital Interfaces for Current Sensing Devices (Rev. A) PDF | HTML 2021年 9月 30日
Application brief Integrating the Current Sensing Signal Path (Rev. B) PDF | HTML 2021年 9月 29日
Application brief Integrated, Current Sensing Analog-to-Digital Converter (Rev. A) PDF | HTML 2021年 9月 28日
Application note Getting Started with Digital Power Monitors (Rev. A) PDF | HTML 2021年 9月 2日
Application note Understanding the I2C Bus PDF | HTML 2015年 6月 30日

設計與開發

如需其他條款或必要資源，請按一下下方的任何標題以檢視詳細頁面 (如有)。

開發板

INA234_236EVM — 適用電流/電壓/電源監控器的 INA232、INA234 和 INA236 評估模組

此評估模組 (EVM) 是一款易於使用的平台，可評估 INA232、INA234 或 INA236 的主要功能與性能。EVM 隨附 GUI 支援，可讀取及寫入至裝置暫存器。
使用指南: PDF | HTML
View Options
IDE、配置、編譯器或偵錯程式

ASC-STUDIO-INA234 — ASC Studio (SysConfig) for configuring all aspects of the INA234 digital power monitor

SysConfig can be used to help simplify configuration challenges and accelerate software development with the INA234 digital power monitor.
支援產品和硬體

支援產品和硬體
啟動
計算工具

ANALOG-ENGINEER-CALC — PC software analog engineer's calculator

The analog engineer’s calculator is designed to speed up many of the repetitive calculations that analog circuit design engineers use on a regular basis. This PC-based tool provides a graphical interface with a list of various common calculations ranging from setting operational-amplifier (...)

支援產品和硬體

支援產品和硬體
啟動 下載
計算工具

CS-AMPLIFIER-ERROR-TOOL — Current Sense Amplifier Comparison and Error Tool

This Excel calculator provides a comparison between two and five of our standard current sense amplifiers, delivering a chart containing the basic parameters of each device. This calculator also takes system condition inputs from users such as common-mode voltage, supply voltage, shunt resistor (...)
支援產品和硬體

支援產品和硬體
下載
計算工具

SBOR021 — Power Monitor Tool

Power Monitor Tool
支援產品和硬體

支援產品和硬體
下載
模擬工具

PSPICE-FOR-TI — PSpice® for TI 設計與模擬工具

PSpice® for TI 是有助於評估類比電路功能的設計和模擬環境。這款全功能設計和模擬套件使用 Cadence® 的類比分析引擎。PSpice for TI 包括業界最大的模型庫之一，涵蓋我們的類比和電源產品組合，以及特定類比行為模型，且使用無需支付費用。

PSpice for TI 設計和模擬環境可讓您使用其內建函式庫來模擬複雜的混合訊號設計。在進行佈局和製造之前，建立完整的終端設備設計和解決方案原型，進而縮短上市時間並降低開發成本。 

在 PSpice for TI 設計與模擬工具中，您可以搜尋 TI (...)
要求
模擬工具

TINA-TI — 基於 SPICE 的類比模擬程式

TINA-TI provides all the conventional DC, transient and frequency domain analysis of SPICE and much more. TINA has extensive post-processing capability that allows you to format results the way you want them. Virtual instruments allow you to select input waveforms and probe circuit nodes voltages (...)
使用指南: PDF
View Options
封裝 針腳 CAD 符號、佔位空間與 3D 模型
DSBGA (YBJ) 8 Ultra Librarian
適用 TI 的評估品項標準條款與條件。

訂購與品質

內含資訊：
  • RoHS
  • REACH
  • 產品標記
  • 鉛塗層/球物料
  • MSL 等級/回焊峰值
  • MTBF/FIT 估算值
  • 材料內容
  • 認證摘要
  • 進行中的可靠性監測
內含資訊：
  • 晶圓廠位置
  • 組裝地點

支援與培訓

內含 TI 工程師技術支援的 TI E2E™ 論壇

以英文檢視所有論壇主題

內容係由 TI 和社群貢獻者依「現狀」提供，且不構成 TI 規範。檢視使用條款。

若有關於品質、封裝或訂購 TI 產品的問題，請參閱 TI 支援。​​​​​​​​​​​​​​

影片