首頁 放大器 運算放大器 (op amps) 一般用途運算放大器
首頁
放大器
運算放大器 (op amps)
一般用途運算放大器

OPA310-Q1

現行

車用、單路 5.5V、3MHz 高輸出電流 (150mA) 快速關機運算放大器

立即訂購
產品規格表

OPA310-Q1

現行
產品規格表 立即訂購

產品詳細資料

Number of channels 1 Total supply voltage (+5 V = 5, ±5 V = 10) (max) (V) 5.5 Total supply voltage (+5 V = 5, ±5 V = 10) (min) (V) 1.5 Rail-to-rail In, Out GBW (typ) (MHz) 3 Slew rate (typ) (V/µs) 3 Vos (offset voltage at 25°C) (max) (mV) 1.3 Iq per channel (typ) (mA) 0.165 Vn at 1 kHz (typ) (nV√Hz) 16 Rating Automotive Operating temperature range (°C) -40 to 125 Offset drift (typ) (µV/°C) 0.5 Features Shutdown, Small Size Input bias current (max) (pA) 30 CMRR (typ) (dB) 95 Iout (typ) (A) 0.15 Architecture CMOS Input common mode headroom (to negative supply) (typ) (V) -0.1 Input common mode headroom (to positive supply) (typ) (V) 0.1 Output swing headroom (to negative supply) (typ) (V) 0.001 Output swing headroom (to positive supply) (typ) (V) -0.001
Number of channels 1 Total supply voltage (+5 V = 5, ±5 V = 10) (max) (V) 5.5 Total supply voltage (+5 V = 5, ±5 V = 10) (min) (V) 1.5 Rail-to-rail In, Out GBW (typ) (MHz) 3 Slew rate (typ) (V/µs) 3 Vos (offset voltage at 25°C) (max) (mV) 1.3 Iq per channel (typ) (mA) 0.165 Vn at 1 kHz (typ) (nV√Hz) 16 Rating Automotive Operating temperature range (°C) -40 to 125 Offset drift (typ) (µV/°C) 0.5 Features Shutdown, Small Size Input bias current (max) (pA) 30 CMRR (typ) (dB) 95 Iout (typ) (A) 0.15 Architecture CMOS Input common mode headroom (to negative supply) (typ) (V) -0.1 Input common mode headroom (to positive supply) (typ) (V) 0.1 Output swing headroom (to negative supply) (typ) (V) 0.001 Output swing headroom (to positive supply) (typ) (V) -0.001
SOT-23 (DBV) 6 8.12 mm² (2.9 mm × 2.8 mm) SOT-SC70 (DCK) 5 4.2 mm² (2 mm × 2.1 mm) SOT-23 (DBV) 5 8.12 mm² (2.9 mm × 2.8 mm) SOT-SC70 (DCK) 6 4.2 mm² (2 mm × 2.1 mm)
  • High output current: ±150mA typical ISC at 5.5V
  • Fast enable from shutdown: 0.9µs typical
  • Wide operational supply voltage: 1.5V to 5.5V
  • Low input offset voltage: ±250µV typical
  • Fail-safe inputs: No diode from inputs to V+
  • Optimized quiescent current: 165µA/ch typical
  • Rail-to-rail input and output
  • Gain bandwidth product: 3MHz typical at 5.5V
  • Thermal noise floor: 16nV/√Hz typical
  • Unity-gain stable
  • Drives up to 250pF without sustained oscillations
  • Internal RFI and EMI filtered input pins
  • Operating temperature range: –40°C to 125°C
  • High output current: ±150mA typical ISC at 5.5V
  • Fast enable from shutdown: 0.9µs typical
  • Wide operational supply voltage: 1.5V to 5.5V
  • Low input offset voltage: ±250µV typical
  • Fail-safe inputs: No diode from inputs to V+
  • Optimized quiescent current: 165µA/ch typical
  • Rail-to-rail input and output
  • Gain bandwidth product: 3MHz typical at 5.5V
  • Thermal noise floor: 16nV/√Hz typical
  • Unity-gain stable
  • Drives up to 250pF without sustained oscillations
  • Internal RFI and EMI filtered input pins
  • Operating temperature range: –40°C to 125°C

The OPAx310-Q1 family of op amps includes single (OPA310-Q1), dual (OPA2310-Q1), and quad-channel (OPA4310-Q1), low-voltage (1.5V to 5.5V), high output current operational amplifiers (op amps) with rail-to-rail input and output swing capabilities. The OPA310S-Q1 variant also features a very fast shutdown response and has a typical enable time of 0.9µs that allows for power savings when the application involves duty cycling the amplifier signal chain. OPAx310-Q1 family has a robust ESD performance with fail safe input ESD structure where there are no diodes connected from inputs to the positive power supply rail.

OPAx310-Q1 is offered in power pad, standard, small size package variants and has an internal current limit protection, thermal shutdown protection that enables additional robustness when operating with high output current. OPAx310-Q1 can swing very close to the rails and has a short-circuit current of 75mA minimum across temperature at 5.5V power supply. Additional output current capability can be achieved by carefully connecting multiple op amps in parallel. OPAx310-Q1 devices are an excellent choice for LED driver and other high current applications and can also be used as a reference buffer, guard amplifier, or as a discrete LDO.

The robust design of the OPAx310-Q1 family simplifies circuit design. These op amps feature an integrated RFI and EMI rejection filter with no-phase reversal in input overdrive conditions. These devices also deliver excellent AC performance with a gain bandwidth of 3MHz and can drive up to 250pF of capacitor load with no sustained oscillations, enabling designers to achieve both improved performance and a lower-power consumption.

The OPAx310-Q1 family of op amps includes single (OPA310-Q1), dual (OPA2310-Q1), and quad-channel (OPA4310-Q1), low-voltage (1.5V to 5.5V), high output current operational amplifiers (op amps) with rail-to-rail input and output swing capabilities. The OPA310S-Q1 variant also features a very fast shutdown response and has a typical enable time of 0.9µs that allows for power savings when the application involves duty cycling the amplifier signal chain. OPAx310-Q1 family has a robust ESD performance with fail safe input ESD structure where there are no diodes connected from inputs to the positive power supply rail.

OPAx310-Q1 is offered in power pad, standard, small size package variants and has an internal current limit protection, thermal shutdown protection that enables additional robustness when operating with high output current. OPAx310-Q1 can swing very close to the rails and has a short-circuit current of 75mA minimum across temperature at 5.5V power supply. Additional output current capability can be achieved by carefully connecting multiple op amps in parallel. OPAx310-Q1 devices are an excellent choice for LED driver and other high current applications and can also be used as a reference buffer, guard amplifier, or as a discrete LDO.

The robust design of the OPAx310-Q1 family simplifies circuit design. These op amps feature an integrated RFI and EMI rejection filter with no-phase reversal in input overdrive conditions. These devices also deliver excellent AC performance with a gain bandwidth of 3MHz and can drive up to 250pF of capacitor load with no sustained oscillations, enabling designers to achieve both improved performance and a lower-power consumption.
filter 尋找其它 一般用途運算放大器
下載 觀看有字幕稿的影片 影片

技術文件

找不到結果。請清除您的搜尋條件，然後再試一次。
檢視所有 1
重要文件 類型 標題 格式選項 下載最新的英文版本 日期
* 資料表 OPAx310-Q1 Automotive High Output Current, 5V, RRIO, 3MHz Operational Amplifier with Shutdown datasheet (Rev. B) PDF | HTML 2024/9/20

設計與開發

如需其他條款或必要資源，請按一下下方的任何標題以檢視詳細頁面 (如有)。

開發板

AMP-PDK-EVM — 放大器性能開發套件評估模組

放大器性能開發套件 (PDK) 是一款評估模組 (EVM) 套件，可測試通用運算放大器 (op amp) 參數，並與大多數運算放大器和比較器相容。EVM 套件提供主板和多個插槽式子卡選項，可滿足封裝需求，使工程師能夠快速評估和驗證裝置性能。

AMP-PDK-EVM 套件支援五種最熱門的業界標準封裝，包括：

  • D (SOIC-8 和 SOIC-14)
  • PW (TSSOP-14)
  • DGK (VSSOP-8)
  • DBV (SOT23-5 和 SOT23-6)
  • DCK (SC70-5 和 SC70-6)
使用指南: PDF | HTML
支援產品和硬體
開發板

DIP-ADAPTER-EVM — DIP 轉接器評估模組

Speed up your op amp prototyping and testing with the DIP-Adapter-EVM, which provides a fast, easy and inexpensive way to interface with small, surface-mount ICs. You can connect any supported op amp using the included Samtec terminal strips or wire them directly to existing circuits.

The (...)

支援產品和硬體
有庫存
限制：
??asset.out-of-stock-ti_zh_TW??
無法提供
開發板

DIYAMP-EVM — 通用自製 (DIY) 放大器電路評估模組

DIYAMP-EVM 是一系列評估模組 (EVM)，提供工程師與自組愛好者 (DIYers) 實作型放大器電路，協助快速驗證設計概念並模擬結果。提供三種業界標準封裝（SC70、SOT-23 和 SOIC）與 12 種常見放大器配置，支援單電源與雙電源架構的放大器、濾波器、穩定補償與比較器應用。

DIYAMP-EVM 可快速製作電路原型，並採用常見的 0805 或 0603 表面裝載元件。透過多種組合方式，此 EVM 可建立從簡單放大器電路到複雜訊號鏈的各種評估電路。此 EVM 支援模擬板、超微型 A 版 (SMA)、接頭和有線介面連接方式，並與大多數類比數位轉換器 (ADC) (...)

使用指南: PDF | HTML
支援產品和硬體
開發板

SMALL-AMP-DIP-EVM — 適用於採用小尺寸封裝之運算放大器的評估模組

SMALL-AMP-DIP-EVM 提供快速簡易方式，與許多業界標準小型封裝進行介接，因而加速小型封裝運算放大器原型設計。SMALL-AMP-DIP-EVM 支援八個小型封裝選項，包括 DPW-5 (X2SON)、DSG-8 (WSON)、DCN-8 (SOT)、DDF-8 (SOT)、RUG-10 (X2QFN)、RUC-14 (X2QFN)、RGY-14 (VQFN) 和 RTE-16 (WQFN)。

使用指南: PDF
支援產品和硬體
有庫存
限制：
??asset.out-of-stock-ti_zh_TW??
無法提供
計算工具

ANALOG-ENGINEER-CALC — PC software analog engineer's calculator

類比工程師的計算機旨在加速類比電路設計工程師定期使用的許多重複計算。此基於 PC 的工具提供圖形介面，列出各種常見計算，從使用回饋電阻器設定運算放大器增益到選擇適當的電路設計元件以穩定類比數位轉換器 (ADC) 驅動緩衝電路。

除了作為獨立工具使用外，此計算機還與類比工程師口袋參考中描述的概念相得益彰。

支援產品和硬體
封裝 針腳 CAD 符號、佔位空間與 3D 模型
SOT-23 (DBV) 6 Ultra Librarian
SOT-SC70 (DCK) 5 Ultra Librarian
SOT-23 (DBV) 5 Ultra Librarian
SOT-SC70 (DCK) 6 Ultra Librarian
適用 TI 的評估品項標準條款與條件。

訂購與品質

支援與培訓

內含 TI 工程師技術支援的 TI E2E™ 論壇

以英文檢視所有論壇主題

內容係由 TI 和社群貢獻者依「現狀」提供，且不構成 TI 規範。檢視使用條款。

若有關於品質、封裝或訂購 TI 產品的問題，請參閱 TI 支援。​​​​​​​​​​​​​​

影片