Product details

Architecture Fixed Gain/Buffer Number of channels (#) 1 Total supply voltage (Min) (+5V=5, +/-5V=10) 5 Total supply voltage (Max) (+5V=5, +/-5V=10) 12 GBW (Typ) (MHz) 280 BW @ Acl (MHz) 280 Acl, min spec gain (V/V) 1 Slew rate (Typ) (V/us) 2100 Vn at flatband (Typ) (nV/rtHz) 1.7 Vn at 1 kHz (Typ) (nV/rtHz) 2 Iq per channel (Typ) (mA) 5.1 Vos (offset voltage @ 25 C) (Max) (mV) 2.5 Rail-to-rail No Features Shutdown Rating Catalog Operating temperature range (C) -40 to 85 Input bias current (Max) (pA) 45000000 Offset drift (Typ) (uV/C) 12 Output current (Typ) (mA) 190 2nd harmonic (dBc) 79 3rd harmonic (dBc) 94 @ MHz 5
Architecture Fixed Gain/Buffer Number of channels (#) 1 Total supply voltage (Min) (+5V=5, +/-5V=10) 5 Total supply voltage (Max) (+5V=5, +/-5V=10) 12 GBW (Typ) (MHz) 280 BW @ Acl (MHz) 280 Acl, min spec gain (V/V) 1 Slew rate (Typ) (V/us) 2100 Vn at flatband (Typ) (nV/rtHz) 1.7 Vn at 1 kHz (Typ) (nV/rtHz) 2 Iq per channel (Typ) (mA) 5.1 Vos (offset voltage @ 25 C) (Max) (mV) 2.5 Rail-to-rail No Features Shutdown Rating Catalog Operating temperature range (C) -40 to 85 Input bias current (Max) (pA) 45000000 Offset drift (Typ) (uV/C) 12 Output current (Typ) (mA) 190 2nd harmonic (dBc) 79 3rd harmonic (dBc) 94 @ MHz 5
SOIC (D) 8 19 mm² 3.91 x 4.9 SOT-23 (DBV) 6 5 mm² 2.9 x 1.6
  • FLEXIBLE SUPPLY RANGE:
      +5V to +12V Single Supply
      ±2.5V to ±6V Dual Supplies
  • INTERNALLY FIXED GAIN: +2 or ±1
  • HIGH BANDWIDTH (G = +2): 225MHz
  • LOW SUPPLY CURRENT: 5.1mA
  • LOW DISABLED CURRENT: 150 µA
  • HIGH OUTPUT CURRENT: 190mA
  • OUTPUT VOLTAGE SWING: ±4.0V
  • SOT23-6 AVAILABLE
  • APPLICATIONS
    • BROADBAND VIDEO LINE DRIVERS
    • MULTIPLE LINE VIDEO DA
    • PORTABLE INSTRUMENTS
    • ADC BUFFERS
    • ACTIVE FILTERS

All trademarks are the property of their respective owners.

  • FLEXIBLE SUPPLY RANGE:
      +5V to +12V Single Supply
      ±2.5V to ±6V Dual Supplies
  • INTERNALLY FIXED GAIN: +2 or ±1
  • HIGH BANDWIDTH (G = +2): 225MHz
  • LOW SUPPLY CURRENT: 5.1mA
  • LOW DISABLED CURRENT: 150 µA
  • HIGH OUTPUT CURRENT: 190mA
  • OUTPUT VOLTAGE SWING: ±4.0V
  • SOT23-6 AVAILABLE
  • APPLICATIONS
    • BROADBAND VIDEO LINE DRIVERS
    • MULTIPLE LINE VIDEO DA
    • PORTABLE INSTRUMENTS
    • ADC BUFFERS
    • ACTIVE FILTERS

All trademarks are the property of their respective owners.

The OPA692 provides an easy to use, broadband fixed gain video buffer amplifier. Depending on the external connections, the internal resistor network may be used to provide either a fixed gain of +2 video buffer or a gain of +1 or –1 voltage buffer. Operating on a very low 5.1mA supply current, the OPA692 offers a slew rate and output power normally associated with a much higher supply current. A new output stage architecture delivers high output current with a minimal headroom and crossover distortion. This gives exceptional single-supply operation. Using a single +5V supply, the OPA692 can deliver a 1V to 4V output swing with over 120mA drive current and > 200MHz bandwidth. This combination of features makes the OPA692 an ideal RGB line driver or single-supply Analog-to-Digital Converter (ADC) input driver.

The low 5.1mA supply current for the OPA692 is precisely trimmed at +25°C. This trim, along with low drift over temperature, ensures lower maximum supply current than competing products that report only a room temperature nominal supply current. System power may be further reduced by using the optional disable control pin. Leaving this disable pin open, or holding it HIGH, gives normal operation. If pulled LOW, the OPA692 supply current drops to less than 150 µA while the I/O pins go into a high impedance state.

The OPA692 provides an easy to use, broadband fixed gain video buffer amplifier. Depending on the external connections, the internal resistor network may be used to provide either a fixed gain of +2 video buffer or a gain of +1 or –1 voltage buffer. Operating on a very low 5.1mA supply current, the OPA692 offers a slew rate and output power normally associated with a much higher supply current. A new output stage architecture delivers high output current with a minimal headroom and crossover distortion. This gives exceptional single-supply operation. Using a single +5V supply, the OPA692 can deliver a 1V to 4V output swing with over 120mA drive current and > 200MHz bandwidth. This combination of features makes the OPA692 an ideal RGB line driver or single-supply Analog-to-Digital Converter (ADC) input driver.

The low 5.1mA supply current for the OPA692 is precisely trimmed at +25°C. This trim, along with low drift over temperature, ensures lower maximum supply current than competing products that report only a room temperature nominal supply current. System power may be further reduced by using the optional disable control pin. Leaving this disable pin open, or holding it HIGH, gives normal operation. If pulled LOW, the OPA692 supply current drops to less than 150 µA while the I/O pins go into a high impedance state.

Download

Technical documentation

star = Top documentation for this product selected by TI
No results found. Please clear your search and try again.
View all 4
Type Title Date
* Data sheet Ultra Wideband, Fixed Gain Video Buffer Amplifier with Disable datasheet (Rev. E) 30 Dec 2008
E-book The Signal e-book: A compendium of blog posts on op amp design topics 28 Mar 2017
Application note Noise Analysis for High Speed Op Amps (Rev. A) 17 Jan 2005
Application note Measuring Board Parasitics in High-Speed Analog Design 07 Jul 2003

Design & development

For additional terms or required resources, click any title below to view the detail page where available.

Evaluation board

DEM-OPA-SO-1A — Single op-amp evaluation module for SO-8 package

The DEM-OPA-SO-1A demonstration fixture helps designers evaluate the operation and performance of TI's High Speed, Wide Bandwidth Operational Amplifiers. This unpopulated PC board is compatible with products offered in the 8-lead SOIC (D) package.

Evaluation board

DEM-OPA-SOT-1A — Single op amp evaluation module for SOT23-5/6 package

The DEM-OPA-SOT-1A is a demonstration fixture that helps designers evaluate the operation and performance of TI's High Speed, Wide Bandwidth Operational Amplifiers. This unpopulated PC board is compatible with products offered in the SOT(DBV) package.

Simulation model

OPA692 TINA-TI Reference Design (Rev. B)

SBOC086B.TSC (98 KB) - TINA-TI Reference Design
Simulation model

OPA692 PSpice Model (Rev. A)

SBOM148A.ZIP (36 KB) - PSpice Model
Simulation model

OPA692 TINA-TI Spice Model (Rev. A)

SBOM168A.ZIP (5 KB) - TINA-TI Spice Model
Simulation tool

PSPICE-FOR-TI — PSpice® for TI design and simulation tool

PSpice® for TI is a design and simulation environment that helps evaluate functionality of analog circuits. This full-featured, design and simulation suite uses an analog analysis engine from Cadence®. Available at no cost, PSpice for TI includes one of the largest model libraries in the (...)
Simulation tool

TINA-TI — SPICE-based analog simulation program

TINA-TI provides all the conventional DC, transient and frequency domain analysis of SPICE and much more. TINA has extensive post-processing capability that allows you to format results the way you want them. Virtual instruments allow you to select input waveforms and probe circuit nodes voltages (...)
Calculation tool

ANALOG-ENGINEER-CALC — Analog engineer's calculator

The Analog Engineer’s Calculator is designed to speed up many of the repetitive calculations that analog circuit design engineers use on a regular basis. This PC-based tool provides a graphical interface with a list of various common calculations ranging from setting op-amp gain with feedback (...)
lock = Requires export approval (1 minute)
Calculation tool

VOLT-DIVIDER-CALC — Voltage Divider Determines A Set of Resistors for a Voltage Divider

VOLT-DIVIDER-CALC quickly determines a set of resistors for a voltage divider. This KnowledgeBase Javascript utility can be used to find a set of resistors for a voltage divider to achieve the desired output voltage. This calculator can also be used to design non-inverting attentuation circuits.

(...)

Package Pins Download
SOIC (D) 8 View options
SOT-23 (DBV) 6 View options

Ordering & quality

Information included:
  • RoHS
  • REACH
  • Device marking
  • Lead finish/Ball material
  • MSL rating/Peak reflow
  • MTBF/FIT estimates
  • Material content
  • Qualification summary
  • Ongoing reliability monitoring

Support & training

TI E2E™ forums with technical support from TI engineers

Content is provided "as is" by TI and community contributors and does not constitute TI specifications. See terms of use.

If you have questions about quality, packaging or ordering TI products, see TI support. ​​​​​​​​​​​​​​

Videos