Home Amplifiers Operational amplifiers (op amps) High-speed op amps (GBW ≥ 50 MHz)
Home
Amplifiers
Operational amplifiers (op amps)
High-speed op amps (GBW ≥ 50 MHz)

OPA2836-Q1

ACTIVE

Automotive, Dual, Very Low Power, Rail to Rail output, VFB Op Amp

Order now
Data sheet

OPA2836-Q1

ACTIVE
Data sheet Order now

Product details

Architecture Voltage FB Number of channels 2 Total supply voltage (+5 V = 5, ±5 V = 10) (min) (V) 2.5 Total supply voltage (+5 V = 5, ±5 V = 10) (max) (V) 5.5 GBW (typ) (MHz) 110 BW at Acl (MHz) 205 Acl, min spec gain (V/V) 1 Slew rate (typ) (V/µs) 560 Vn at flatband (typ) (nV√Hz) 4.6 Vn at 1 kHz (typ) (nV√Hz) 5 Iq per channel (typ) (mA) 1 Vos (offset voltage at 25°C) (max) (mV) 0.4 Rail-to-rail In to V-, Out Rating Automotive Operating temperature range (°C) -40 to 125 CMRR (typ) (dB) 116 Input bias current (max) (pA) 1000000 Offset drift (typ) (µV/°C) 1.1 Iout (typ) (mA) 50 2nd harmonic (dBc) 85 3rd harmonic (dBc) 79 Frequency of harmonic distortion measurement (MHz) 1
Architecture Voltage FB Number of channels 2 Total supply voltage (+5 V = 5, ±5 V = 10) (min) (V) 2.5 Total supply voltage (+5 V = 5, ±5 V = 10) (max) (V) 5.5 GBW (typ) (MHz) 110 BW at Acl (MHz) 205 Acl, min spec gain (V/V) 1 Slew rate (typ) (V/µs) 560 Vn at flatband (typ) (nV√Hz) 4.6 Vn at 1 kHz (typ) (nV√Hz) 5 Iq per channel (typ) (mA) 1 Vos (offset voltage at 25°C) (max) (mV) 0.4 Rail-to-rail In to V-, Out Rating Automotive Operating temperature range (°C) -40 to 125 CMRR (typ) (dB) 116 Input bias current (max) (pA) 1000000 Offset drift (typ) (µV/°C) 1.1 Iout (typ) (mA) 50 2nd harmonic (dBc) 85 3rd harmonic (dBc) 79 Frequency of harmonic distortion measurement (MHz) 1
VSSOP (DGK) 8 14.7 mm² 3 x 4.9
  • Qualified for Automotive Applications
  • AEC-Q100 Qualified With the Following Results:
    • Device Temperature Grade 1: –40°C to 125°C Ambient Operating Temperature Range
    • Device HBM Classification Level 2
    • Device CDM Classification Level C6
  • Low Power:
    • Supply Voltage: 2.5 V to 5.5 V
    • Quiescent Current: 1 mA (Typ)
    • Power-Down Mode: 0.5 µA Typ)
  • Bandwidth: 205 MHz
  • Slew Rate: 560 V/µs
  • Rise Time: 3 ns (2 VSTEP)
  • Settling Time (0.1%): 22 ns (2 VSTEP)
  • Overdrive Recovery Time: 60 ns
  • SNR: 0.00013% (–117.6 dBc) at 1 kHz (1 VRMS)
  • THD: 0.00003% (–130 dBc) at 1 kHz (1 VRMS)
  • HD2, HD3: –85 dBc, –105 dBc at 1 MHz (2 VPP)
  • Input Voltage Noise: 4.6 nV/√Hz (f = 100 kHz)
  • Input Offset Voltage: 65 µV (±400-µV Max)
  • CMRR: 116 dB
  • Output Current Drive: 50 mA
  • RRO: Rail-to-Rail Output
  • Input Voltage Range: –0.2 V to +3.9 V
    (5-V Supply)
  • Qualified for Automotive Applications
  • AEC-Q100 Qualified With the Following Results:
    • Device Temperature Grade 1: –40°C to 125°C Ambient Operating Temperature Range
    • Device HBM Classification Level 2
    • Device CDM Classification Level C6
  • Low Power:
    • Supply Voltage: 2.5 V to 5.5 V
    • Quiescent Current: 1 mA (Typ)
    • Power-Down Mode: 0.5 µA Typ)
  • Bandwidth: 205 MHz
  • Slew Rate: 560 V/µs
  • Rise Time: 3 ns (2 VSTEP)
  • Settling Time (0.1%): 22 ns (2 VSTEP)
  • Overdrive Recovery Time: 60 ns
  • SNR: 0.00013% (–117.6 dBc) at 1 kHz (1 VRMS)
  • THD: 0.00003% (–130 dBc) at 1 kHz (1 VRMS)
  • HD2, HD3: –85 dBc, –105 dBc at 1 MHz (2 VPP)
  • Input Voltage Noise: 4.6 nV/√Hz (f = 100 kHz)
  • Input Offset Voltage: 65 µV (±400-µV Max)
  • CMRR: 116 dB
  • Output Current Drive: 50 mA
  • RRO: Rail-to-Rail Output
  • Input Voltage Range: –0.2 V to +3.9 V
    (5-V Supply)

The OPA2836-Q1 device is a dual-channel, ultra-low power, rail-to-rail output, negative-rail input, voltage-feedback operational amplifier designed to operate over a power-supply range of 2.5 V to 5.5 V (single supply), or ±1.25 V to ±2.75 V (dual supply). Consuming only 1 mA per channel with a unity-gain bandwidth of 205 MHz, this amplifier sets an industry-leading, power-to-performance ratio for rail-to-rail amplifiers.

For battery-powered, portable applications where power is a key importance, the low-power consumption and high-frequency performance of the OPA2836-Q1 offers designers performance-versus-power that is not attainable in other devices.

The OPA2836-Q1 is characterized for operation over the extended industrial temperature range of –40°C to +125°C.

The OPA2836-Q1 device is a dual-channel, ultra-low power, rail-to-rail output, negative-rail input, voltage-feedback operational amplifier designed to operate over a power-supply range of 2.5 V to 5.5 V (single supply), or ±1.25 V to ±2.75 V (dual supply). Consuming only 1 mA per channel with a unity-gain bandwidth of 205 MHz, this amplifier sets an industry-leading, power-to-performance ratio for rail-to-rail amplifiers.

For battery-powered, portable applications where power is a key importance, the low-power consumption and high-frequency performance of the OPA2836-Q1 offers designers performance-versus-power that is not attainable in other devices.

The OPA2836-Q1 is characterized for operation over the extended industrial temperature range of –40°C to +125°C.
open-in-new Find other High-speed op amps (GBW ≥ 50 MHz)
Download View video with transcript Video

Technical documentation

star =Top documentation for this product selected by TI
No results found. Please clear your search and try again.
View all 3
Type Title Date
* Data sheet OPA2836-Q1 Very-Low Power, Rail-to-Rail Out, Negative-Rail In, Voltage-Feedback Operational Amplifier datasheet PDF | HTML 06 Dec 2016
Application note Increase Measurement Accuracy With HS Amps for Low-Side Shunt Current Monitoring (Rev. A) 26 Aug 2019
E-book The Signal e-book: A compendium of blog posts on op amp design topics 28 Mar 2017

Design & development

For additional terms or required resources, click any title below to view the detail page where available.

Evaluation board

ADS7945EVM-PDK — ADS7945 Performance Demonstration Kit

The ADS794xEVM-PDK is designed to evaluate the ADS7945 and ADS7946 analog-to-digital converters. These converters are 14-bit dual-channel differential SAR converters with a maximum throughput rate of 2MSPS. The ADS7945 offers fully-differential input voltages while the ADS7946’s pseudo (...)

User guide: PDF
View options
Evaluation board

OPA2836IDGSEVM — OPA2836 Evaluation Module for VSSOP/MSOP Package

The OPA2836IDGSEVM is an evaluation module for the dual, OPA2836 in the DGS (10-lead VSSOP (MSOP)) package.

The OPA2836IDGSEVM is designed to quickly demonstrate the functionality and versatility of the amplifier(s). The EVM is ready to connect to power, signal source, and test instruments through (...)

User guide: PDF
Not available on TI.com
Simulation model

OPA2836 PSpice Model

SLOM242.ZIP (61 KB) - PSpice Model
Download
Simulation model

OPA2836 TINA-TI Spice Model

SLOM240.ZIP (8 KB) - TINA-TI Spice Model
Download
Calculation tool

ANALOG-ENGINEER-CALC — Analog engineer's calculator

The analog engineer’s calculator is designed to speed up many of the repetitive calculations that analog circuit design engineers use on a regular basis. This PC-based tool provides a graphical interface with a list of various common calculations ranging from setting operational-amplifier (...)
Download
Calculation tool

VOLT-DIVIDER-CALC — Voltage Divider Determines A Set of Resistors for a Voltage Divider

VOLT-DIVIDER-CALC quickly determines a set of resistors for a voltage divider. This KnowledgeBase Javascript utility can be used to find a set of resistors for a voltage divider to achieve the desired output voltage. This calculator can also be used to design non-inverting attentuation circuits.

(...)

Design now
Simulation tool

PSPICE-FOR-TI — PSpice® for TI design and simulation tool

PSpice® for TI is a design and simulation environment that helps evaluate functionality of analog circuits. This full-featured, design and simulation suite uses an analog analysis engine from Cadence®. Available at no cost, PSpice for TI includes one of the largest model libraries in the (...)
Request
Simulation tool

TINA-TI — SPICE-based analog simulation program

TINA-TI provides all the conventional DC, transient and frequency domain analysis of SPICE and much more. TINA has extensive post-processing capability that allows you to format results the way you want them. Virtual instruments allow you to select input waveforms and probe circuit nodes voltages (...)
User guide: PDF
View options
Reference designs

TIDA-060019 — High-speed current shunt monitor reference design

This reference design is a low-side, bidirectional current shunt monitor using high-speed amplifiers. It is intended for applications that could benefit from faster fault detection, single shunt motor control, higher switching frequencies, higher gain, and or reduced general ADC sampling noise. (...)
Design guide: PDF
Schematic: PDF
Package Pins Download
VSSOP (DGK) 8 View options
TI's Standard Terms and Conditions for Evaluation Items apply.

Ordering & quality

Information included:
  • RoHS
  • REACH
  • Device marking
  • Lead finish/Ball material
  • MSL rating/Peak reflow
  • MTBF/FIT estimates
  • Material content
  • Qualification summary
  • Ongoing reliability monitoring

Support & training

TI E2E™ forums with technical support from TI engineers

View all forum topics

Content is provided "as is" by TI and community contributors and does not constitute TI specifications. See terms of use.

If you have questions about quality, packaging or ordering TI products, see TI support. ​​​​​​​​​​​​​​

Videos